what is the best configuration betwen vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200
View 10 Replieswhen replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies View Relateddirect me to a document detailing the order that line cards are supposed to boot in a 6500? I'm noticing random boot sequences in some of my chassis,?Note: We currently run Sup720 3CXL for the most part.
View 6 Replies View RelatedOn a number of 6500 chassis it appears that linecard 3 did exist at somepoint, but was removed.Problem is that when issuing the 'show int desc' or 'show ip int brie' the ports for the still appear, and indeed same with 'show run' and 'show conf'.
View 1 Replies View Relatedi have server with two uplink to pair of 6500 non-VSS, this server member of vlan 100 sw-1 is active HSRP while sw2 is a standby HSRP , how can i make this server forward traffic on both Link . the server admin told me only one link is active (green) on the server while the other link is orange
View 5 Replies View Relatedwhat is the best configuration between vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200.
View 6 Replies View RelatedI have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.
I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP
my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?
I have 2 servers, one active, the other standby, both will be using the same IP. If the active fails then a re-patch for the standby to make this the active. I understand that i will need to clear the arp & maybe mac address table on the 6500 for the new active server to work, as the failed server will have its mac address on the 6500,.
is there a way around this so i dont have to clear the arp cache & clear the mac table? [code]
cisco WS-C6509-E Core switch with IOS "s72033-ipservicesk9_wan-mz.122-18.SXF11"
i have 2 question
Q.1 i want to upgrade this switch what is the latest IOS ver. supported by this module ?
Q.2 i need to enable http server on this switch when i run this comman it's accsebt but i cant get http work
I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies View RelatedI have a question regarding fabric storage and cisco catalyst switch 3650.My plan is connecta a esxi server to a nexus switch and then to a san storage. I want add a new switch to have a redundant link between esxi and the storage.Can I use a cisco catalyst 3650 with a fiber conecction to connect the HBA esxi server card to 3650 sw and the SAN storage to the 3650 sw ?
View 2 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedI have a pair of router Cisco 2800 running in HSRP, now I want to configure one sub interface with another sub net, Will my current IP on physical interface work or do I need to create two Sub interfaces for each network. Do i must need encapsulation on sub interface
Current Config:-
Router 1:-
interface FastEthernet0/1description Connect to LAN_SW1 Gi1/0/1ip address 192.168.1.13 255.255.255.0no ip redirectsduplex autospeed autostandby 1 ip 192.168.1.1standby 1 priority 90standby 1 preempt
Router 2:-
interface FastEthernet0/1description Connect to LAN_SW2 Gi1/0/1ip address 192.168.1.3 255.255.255.0no ip redirectsduplex autospeed autostandby 1 ip 192.168.1.1standby 1 priority 110standby 1 preempt
For second network I do not require HSRP
Router 1:-
interface FastEthernet0/0description Connect to LAN_SW1 Gi1/0/1no ip addressduplex fullspeed 100
[ code]...
Router 2:-
interface FastEthernet0/0description Connect to LAN_SW2 Gi1/0/1no ip addressduplex fullspeed 100
[Code]...
Firewall: ASA 5510
Switch: Linksys SRW2048
Physical topology: PC - > VLAN99 - > SRW2048 - trunk - > ASA5510
Switch Setup:
I've been tasked with breaking up a network that has run out of IP's, and have decided to use VLANs to accomplish this. I have to use an ASA5510 to accomplish all the routing between hosts in different VLANs.Port 48 is trunked to the ASA eth0/0 interface, with VLAN 99 and VLAN 20 tagging packets, VLAN 1 Untagged. Hosts hooked up to appropriate ports on Switch.
Are there any physical characteristic differences between the 6509 and 6509-E chassis?
View 4 Replies View RelatedI have 2 ASA5510's acting as routers/firewalls, setup on a LAN, each one pointing to a different gateway (different ISPs), and the exact same VLANs set up as sub-interfaces on each of these. Both act as DHCP relays to a Windows Server 2008 DHCP server. All the Trunking has been setup and works. When I Untag a switch port, and point it to whichever gateway?
View 2 Replies View RelatedI am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies View Relatedvlan interface and physical interface (that is serving for this vlan ) have different input/output counters, there is only one physical interface in this vlan .
sh int vlan 64
30 second input rate 9000 bits/sec, 9 packets/sec
30 second output rate 0 bits/sec, 0 packets/sec
[Code]....
WE got our ESXi servers recently moved from a 6513 to nexus 2000 FEXs uplinked to a nexus 5000s basically we have enhanced vPC and nics goin to 2 different FEXs and they uplink to 2 nexus 5000.
the Vswitch for VMs is setup in a VPC. Question is do the traffic from each vm going in/out of these nics in a vpc actually use both physical links? How can i tell from the switch?
We have recently upgraded oor LAN and we are using couple of Nexus5548UP switches in the core with 2960 stacks as access switches. Each access switches stack is connnected to both core switches with link being port-chanels and VPCs. All is working fine, but our SolarWinds management platform (NPM) is being flooded with "Physical Address changed" events. Here is an example of messages:
NSW_Core_2 - Ethernet1/7 Physical Address changed from 000000003811 to 73616D653811
NSW_Core_2 - Ethernet1/7 Physical Address changed from 200B82B43811 to 000000003811
For each interface I have messages like these repeating.I am not sure what those messages means or if there is actually anything wrong. Performance of the network is good, there are no errors on any interfaces and I do not see anything related in the switch loggs.
how to configure this. I did it in the past but kind of forgot how I did it.I have a stacked 3750 (two physical switches) connecting to a 2960.
I am creating trunk ports with limited access to VLAN 300, 600, and 700.
There is two interfaces connected from the 3750's(one on each physical stack member) to the 2960.I have the physical interfaces configured exactly the same.
3750 Config:
interface Port-channel2
!
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1, 300,600,700
switchport mode trunk
speed 100
[code]....
Should I keep the configuration on the physical ports and not configure the Port-Channel Interfaces? Do I need to configure port-channel load balancing? Is the channel-group mode sufficient? Goal is to basically create 2 links to the 2960 to double the bandwidth and provide redundancy.
What the different between using hsrp on vlan interface and on physical port (routed port) on Cisco 3750 Switch? Wha the benefits?
View 3 Replies View RelatedI've Nexus 7010 switch installed in my DC. I've conncected Cisco router to one of the Ports. On the same port I'm getting following error message and hence, unable to form EIGRP neighborship.
DR-CORE-SW-S01-NEXUS7K %MODULE-2-MOD_SOMEPORTS_FAILED:
Module 1 (serial: JAF*******NGK) reported failure on ports 1/2-1/2 (Ethernet) due
to R2D2 : Speed patch failed - no frames transmitted in device 143 (error 0xc8f0
1273)
We'll be implementing Cisco NAC guest server for Guest Wireless users, ( Model #3310), the question is do we need to configure separate physical interface for User authentication requests( from Wireless ) and a separate Interface for Guest server to talk to AD for SSO?
View 2 Replies View RelatedI have Internet connection in Ethernet Medium connected to a L2 Switch (Cisco 2960). I have 2 Routers (Cisco 2900). I have a webserver to be accessed from Internet. The physical IP address of the server is Private range.
I have configured Stateful NAT as below
157.220.100.61 is Static NAT to 10.1.1.3 using redundancy
Though HSRP is working good, when RTR-1 is down, I am not able to reach Webserver (10.1.1.3) using RTR-2
We found in the that ISP Switch, that even when RTR-1 is down, the MAC address for 157.220.100.61 is still present one pointing to RTR-1 and other pointing to RTR-2. There are 2 MAC address entries for 157.220.100.61
As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies View RelatedWhere is the "ip routing" command in Cisco switch 6500 series?
is the ip routing enable by default accoridng to the: [URL]
Im looking for MIB for monitoring 6500 line card from availability prespective;
View 1 Replies View Related