Cisco Switching/Routing :: To Find Out The Serial No For Cip Card 7500
Feb 8, 2012How do we find out the serial no. for a CIP card on a cisco 7500 router.
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2811 - New Serial Card Interface Not Detected?
Mar 26, 2012I have existing cisco 2811 (Version 12.4(3c)). I try to add a HWIC serial card into the router but the new HWIC is not detected. There is no new interfece shows up when i do show run. This HWIC is a new card just bought it.
View 7 Replies View RelatedHow To Put A Wireless Card On Dell Inspiron 7500
May 2, 2011How to put a wireless card on dell inspiron 7500
View 2 Replies View RelatedCisco WAN :: 2911 Does Not Support NM-E3/T3 Serial Card?
Jun 14, 2011From all of the documentation I am seeing, the 2911 does not support the NM-E3/T3 serial card.
View 16 Replies View RelatedCisco WAN :: 2600 Remove Serial T1 Card From Router Config
Jul 23, 2012I have recently made a WAN change from T1 to fiber and my Cisco 2600 series router no longer needs to connect over the Serial T1 card. The Serial connection also provided a few voice channels for the old phone system that are no longer needed. I need to keep Main Cisco 2600 router in place because I have many network devices that use it as the gateway instead of my firewall. I will not require the second subnet for Offsite Cisco 2600 anymore either. commands that will be required to remove all instances of the Serial connection and Offsite Cisco 2600. I have included the config of the Main Cisco 2600 below. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Need To Know Serial Number Of Sup720
Dec 10, 2011How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies View RelatedCisco Switching/Routing :: AS 5350 XM - Serial Number
Oct 16, 2011I have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies View RelatedCisco Switching/Routing :: No Serial Connections With 2911
May 8, 2011I have 2 2911 routers that will be connected via fiber with an ethernet Gig handoff to each router. Each router will then be connected to local networks on a second ethernet interface on the router. I have always connected routers via serial connections so this is new to me. Outside of the usual ethernet interface addressing configuration, is there anything else that would need to be configured on the 2 routers?
View 1 Replies View RelatedCisco Wireless :: WCS 4.2 - How To Find Serial Number
Feb 8, 2009We are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.
View 10 Replies View RelatedCisco Switching/Routing :: C2960S Flexstack Serial Number
Mar 21, 2012Is there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies View RelatedCisco Firewall :: Find PIX 515e Serial Number?
Sep 27, 2011How can I find the serial number at Cisco PIX-515E ?
View 2 Replies View RelatedCisco Switching/Routing :: 4900 Failed To Read Transceiver Serial
Jul 30, 2012When I insert the TwinGig Converter in a Catalyst 4900M you get the following error message: Failed to read transceiver serial eeprom on port Te2/1, try reinserting.This error is probably because the device expects 10Gig transceivers to be connected to the device not 1Gig.I used the TwinGig 4 module and 8 SFP ports are connected. But when i type in the the "hw-module module <slot> port-group <group> select gigabitethernet" the command is not available. [code]
View 1 Replies View RelatedCisco Switching/Routing :: Location Of Nexus 1010 Serial Number?
Jun 5, 2013Where on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies View RelatedCisco Switching/Routing :: 1841 - Connecting Routers Via Serial Interface
Oct 22, 2012While I managed to connect to each router individually, I decided it was time to connect the routers together via serial; as I don't have any serial cables and need to buy some, what serial cables I need, as well as to ask whether I have the right cards in my router(s) that will allow me to do so.
I bought 3 1841 routers, and all have a 1 port serial WAN Interface Card (WIC 1-T); one router has 2 of these, and one router has a WIC-1B-S/T .. My question is, can I connect the routers with a serial cable via WIC 1-T, or do I need a 2-T
Cisco Switching/Routing :: 2950 Laptop Doesn't Have Serial Port
Feb 15, 2013I have two 2950 Switches and am trying to connect via my laptop. My laptop doesn't have a serial port so I am trying to connect through the ethernet port, with a straight through cable and on the end as it goes into the console port I have bought a cisco console rollover adapter.When I turn on terra term I get nothing...just a black screen and it disconnects.
View 6 Replies View RelatedFind The Serial Number Of Lexmark Pro 900 Series Printer?
Dec 13, 2011i need the address of my pro 900 series printer to install the program for my Sony note pad
View 2 Replies View RelatedCisco Switching/Routing :: PPP Multilink Not Coming Up On Serial Interface / 3620 Router?
Nov 1, 2011I just finished setting up a bundle of (2) T1's in a multilink bundle and I'm having issues with one of the T1's not wanting to join the bundle.
The router I'm using on the remote office location is a 3620 router running code c3620-i-mz.121-1c.bin
The campus router which is a 7206 is setup the same exact way with multilink 240 and like I've said, serial 0/0 is joined to the bundle just fine, so we are running off one T1 connection.
The serial interface that is not working is: serial 0/1
Here is a show-run:
interface Multilink240
ip address 172.18.xxx.xxx 255.255.255.252
ip route-cache flow
ip ospf network point-to-point
service-policy output PhonesFirst
ppp multilink
[code].....
Cisco Switching/Routing :: CatOS 2948G Serial Number - Show Version / Sprom And Sticker Don't
Oct 25, 2012I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
Cisco Switching/Routing :: Using SD Card Slot On ME3600X
Mar 13, 2013we are trying to use the SD Card Slot on an Cisco ME3600X (ME-3600X-24FS-M) IOS Version 15.2(4)S2. If i try to copy a file from the sd card slot to the flash there is no Option like "slot0:" or something alse and no syslog message appers while adding the SD Card.
View 5 Replies View RelatedCisco Switching/Routing :: 2801 - Get IOS On Flash Card?
Mar 15, 2012I have this 2801 in a critical environment. We had a brief power blip, and even though the router is on UPS, something happened. Anyway, after working with TAC, they determined the flash card had gone corrupt. Lucky for me I had a spare 2801 in my office, I grabbed that flash card and plugged it in and we're back up and going.
TAC sent me a new flash card. No matter what I do, I cannot get IOS to load on this thing! I am stuck in rommon. Here's what I've tried:
tftpdnld in rommon, times out. using another 2801 as a tftp-server. doesn't complete. using xmodem. ugh. never seems to get started. booting the router with a known good flash card, so I can get to ena, and "copy tftp flash".
have used tftpd32, Solar Winds TFTP server, What's Up Gold TFTP server, and open source tftp from sourceforge. With the tftp32, it always gets to exactly 73% download and then times out (it says, I have a feeling it's noty really a timeout). I have tried having the router and tftp server the only devices on a switch, i have tried the router plugged directly into the tftp server with a cross connect cable. No happiness. The open source tftp server reported (and I have to paraphrase, I am not near the router) "client does not support block number recount" or something like that. The client being the 2801.
The iOS file is about 45M. Someone asked me if the flash card was formatted...would that matter? would the tftp even start if it wasn't?
OK, I've gone on long enough. TAC is dispatching a new card AND 2801!
Cisco Switching/Routing :: EHWIC4ESG Card Into 1941
Apr 4, 2013Recently my company buy a EHWIC4ESG card and put into the cisco 1941. The reason we buy this card is because the in built two network ports of cisco 1941 are being used up. g0/1 is being connected to the internet and g0/0 is being connected to the office switch (192.168.5.x)
We have two servers (192.168.6.x and 158.55.33.x) that required to be connected to this router 1941 where the router will be configured as VPN for external user to access this server.
The EHWIC4ESG card is put into the router 1941 and after typing the "running-config" command, i could see it create a vlan 1 interface and
interface GigabitEthernet0/1/0
interface GigabitEthernet0/1/1
interface GigabitEthernet0/1/2
interface GigabitEthernet0/1/3
[Code]...
Cisco Switching/Routing :: 3725 - Format CF Card On 1841
Dec 26, 2011I have 3725 router with internal CF and external slot for CF. I tried upgrading and ended up deleting the iOS version on the internal flash, and can not now put the iOS back!! I turned it off.... so there was no active iOS..
I have tried formatting the CF card on an 1841 but the 3725 won't read it. It is obviously stuck at ROMMON
What is the correct way to format a CF card so my 3725 will read it and I can get an iOS back on it!!
Cisco Switching / Routing :: 16 / 24 Port Ethernet Card For 2800?
Jan 11, 2012I am looking a 16 or 24 Port Ethernet (NON POE) card for my 2800 Cisco Router NM-16ESW is EOL/EOS and the replacement is shown as SM-ES2-24 However SM-ES2-24 is not supported on Cisco 2800 Series.
View 2 Replies View RelatedCisco Switching/Routing :: Reading 4/port Card Of 1811
Aug 30, 2012I have a Cisco 1811 with a 4/port Serial Async/Sync (HWIC 4 A/S) and another 2 port A/S serial wic. My router seems to have a problem reading the 4/port card. I did some research and it looks like there shouldn't be a compatibility issue.
View 7 Replies View RelatedCisco Switching/Routing :: Nexus 5k With L3 Card Showed Offline?
Aug 30, 2011i have a nexus 5k with a l3 card i'm not able to bring online
NX-OS is:5.0(3)N2 (1)
L3 card is:L55D160L3
i inserted L3 module several time with the same resul...if i perform a show module i see the card offline. At the boot switch show an error message:
L3 module is down due to a BTCM down..
Cisco Switching/Routing :: To Replace A Line Card WS-X6748-SFP
Oct 18, 2012I urgently want to replace a faulty line card WS-X6748-SFP with a new one. The switch concern is a 5609-V-E operating in Virtual Switching System mode.How long do you suggest the down time will be?
View 1 Replies View RelatedCisco Switching/Routing :: High Density Card For 6500E And 2T SUP
Jun 5, 2012I have a customer that in the past has been using 6506E chassis with Sup32 and the WS-X6196-21AF cards for their closet.With the End of Sale of this combination and the announced End of Sale of the Sup720-3B announced, this kind of pushes the configuration to a Sup 2T.BUT the SUP 2T does not support these low speed high density cards.
Is there a card coming that will address need? Customer generally has had dual sup32's and 3 to 4 cards of the 96port AF.They stock spares besides haveing smartnet on the boxes or moving to a different platform like the 4510R+ or stacks of switches will mess them up.
Cisco Switching/Routing :: ESX Server With 10 Physical NIC Card And 6500?
Jul 14, 2008what is the best configuration betwen vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200
View 10 Replies View RelatedCisco Switching/Routing :: 2620 NM-2FE2W Card Not Being Detected
Dec 28, 2011I am attempting to add an additional ethernet port on a Cisco 2620 router using a NM-2FE2W card, however the card is not being detected. I read that this card is compatible with this model router, but I have also notice that there is a version 2 of this card. Have I ordered the wrong card or do I possibly have a defective card? My ISO version is 12.2(26) on the router.If this card is not compatible, what is the recommended card for adding an additional ethernet port on this router?
View 2 Replies View RelatedCisco Switching/Routing :: Nexus 5548UP VPC Domain With 1x L3 Card
Apr 9, 2013I can't find anywhere whether it is possible to create a vPC domain with 2 Nexus 5548UP switches, where only 1 Nexus 5548UP has a L3 daughter card.
View 3 Replies View RelatedCisco Switching/Routing :: Add WS-X6716-10GE Card In CAT6509
Sep 8, 2011I will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
Cisco Switching/Routing :: 6509 Line Card Not Showing
Jun 30, 2008Cisco Catalyst 6509 Chassis.We have moved a line card from slot 8 to slot 6, but config remains for the line card in slot 8 and nothing is seen in slot 6.
We are running on IOS Verison 12.2 (33SXH2A) i.e. VSS.Blade model number is WS-X6748.
Cisco Switching/Routing :: Configuring VWIC3-4MFT-T1/E1 Card?
Jul 24, 2012Is there any in depth documentation on how to configure a VWIC3-4MFT-T1/E1 card? It will sit in a CISCO2911/K9. The network is point to point T1s - a quantity of four coming into this router.
View 1 Replies View Related
