Cisco Switching/Routing :: Need To Know Serial Number Of Sup720
Dec 10, 2011How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 RepliesHow can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 RepliesI have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies View RelatedIs there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies View RelatedWhere on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies View RelatedI am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
i have LMS 3.2 installed in my campus. i need the serial number of the LMS suite to open a service request with cisco. but unable to find the same. How to find the same.
View 1 Replies View RelatedHow to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies View RelatedI'm based in the UK and am using a DIR-655 router but I have no record of its serial number (there is no sticker on the item, and the original box is now missing) - is there any way I can ascertain which version of the router I have? As I understand matters, I need to know this so that I can apply the correct firmware upgrade, which is what I wish to do.
View 1 Replies View RelatedWhat is the equivalent oid as chassisid - .1.3.6.1.4.1.9.3.6.3.0, which gets the serial number for most cisco switches/routers is for the ASA 55XX series firewalls.
View 2 Replies View RelatedI need to get the serial number of SFP in WLC 5508 ver 7.0 but can't find the command, is this possible and if yes how can I get the S/N of SFF in WLC?
View 4 Replies View RelatedWe are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.
View 10 Replies View RelatedI have a problem with an AP1310 which may need me to open a case for RMA. is there any way I can view the serial number using the GUI since the AP is already installed on a high mast but I didn't enable telnet on that?
View 1 Replies View RelatedHow can I find the serial number at Cisco PIX-515E ?
View 2 Replies View Relatedi need the address of my pro 900 series printer to install the program for my Sony note pad
View 2 Replies View RelatedIm trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?
View 4 Replies View RelatedI am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies View RelatedI have a faulty ASA5520 and I am not sure if I have a SMART net contract for it or not (I manage over 200+ ASAs). The problem is that the Serial Number sticker that is normally on the back of the ASA is missing. The ASA5520 is also faulty and doesn't power on so I cannot boot it up and run 'show ver' or similar. If I open the chassis there appears to be other Serial numbers on the Power Supply, and Motherboard etc but they do not seem to be the correct Chassis serial number i.e not in the right format, and if I put them into the Trade tool I get no results.
There must be another record of the serial numbers besides 1x sticker to the rear of the chassis that can fall off? How I can get the chassis serial when the device isn't booting. or (Cisco) is there a way to find the chassis serial number from the power or motherboard serial?
My Sony Vaio was stolen and I dont have any tracking software on it. I was told it can be traced using the serial number this is not going to work as the serial number is not digital is this correct? If so is there any inbuilt device or software ect: that comes installed when you purchase the laptop? I am desperate to find my laptop as it has personal information stored on it of my partner who recently passed away and non of this is replaceable. I would prefer to find it without using the authorities as i know who this person is i just dont know where this person has stored the laptop. It would be best for the authorities not to be involved for my safety.
View 5 Replies View RelatedMy laptop "hp pavillion dm4-1065dx" hass been stolen and i have not installed any theft or tracking related softwares. Kindly tell me how to work dis out and find my laptop.
View 1 Replies View RelatedThis is the second one of the new ASA 55.5X series appliances where I have seen this issue:When I SHOW VERSION, I can see the serial number displayed. However, this does not match the serial number from the sticker affixed to the outside of the chassis.This makes it confusing on opening TAC cases and for updating licenses.
View 8 Replies View RelatedI will use function of span in sup70-3b.How many session can use in sup720-3b? For example, 2 or 4 session.
View 1 Replies View RelatedI have a SUP720-3BXL that will not boot. It will get stuck at booting from the SP. It never switches over to the RP. [code]
View 5 Replies View RelatedI have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?
View 7 Replies View Relatedwhen using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?
IOS is 12.2(33)SXI5.
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine
[Code]....
I got a new VS-S720-10G it had 122-33.SXH8b on there. I had to downgrade it to 12.2.33.SXI1 to match our other switches. I installed the file I use in all the other switches, s72033-adventerprisek9_wan-mz.122-33.SXI1.bin but the Sup is now is only booting up only to ROMMON mode.
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : #################################################
################################################################################
################################################################ [OK]
%SYSTEM-1-INITFAIL: Network boot is not supported.
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code]....
How do I get the older version of IOS to load up?
I have problem with the standby supervisor in 6500 vss and need to replace the supervisor. I have follow how-to on the cisco web site url...
But when i boot the new standby sup720 it comes active and both supervisors is rebooting. I wonder if i can do the replacement without rebooting both active and standy supervisor.
Trying to find documentation on the proper procedure for installing a second sup720 into our 6509-E chassis for sup redundancy. I have found documents that tout how 'cool' and 'awesome' NSF/SSO, and all that is, but haven't found any docs on installing a second sup720 into a chassis that is currently in production and is only running one sup720. In all the years that this chassis has been out, there must me a documented procedure out here to explain this.I have been through the following pages, and have found nothing to this effect.
View 1 Replies View Relatedproblem to configure MWAM. I have installed MWAM module in 6506-E slot 2 with sup720-3B. After installing MWAM the Status is PwrDown. I tried to turn on the power but its not happening. MWAM is installed in slot 2 and here is the result of show module 2 My Sup720-eB IOS image is s72033-advipservicesk9_wan-mz.122-33.SXJ1.bin
6506-E#show module 2
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 3 MWAM Module WS-SVC-MWAM-1 SAD081203GK
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 0003.feae.bb8c to 0003.feae.bb93 3.0 Unknown Unknown PwrDown
Mod Online Diag Status
---- -------------------
2 Not Applicable
We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies View RelatedCustomer is using SUP720 with SP rommon image version 8.1(3), he is trying to boot the new ios image from disk0, but he gets invalid magic error. he fomat the disk0 but still he gets error when he boots from disk0. He suspect that it can't be flash problem but can be software of hardware as he has two flash with same issue on 2 switches.
Customer wanted to recreate, I tried in the lab, i was able to load from disk0, but sup in lab had 8.5(4).
Customer wanted me try with 8.1(3) version. But i was unable to downgrade the SP Rommon image. SP rommon is running in Gold region and I loaded the 8.1(3) from both disk0 and sup-bootdisk, even preferrence was given to region1 but still sup came up with gold region itself.
* Will i be able to downgrade from 8.5(4) to 8.1(3), if so, what are the steps.
* is there any limitation or bug where 8.1(3) will be unable to read disk0.
Just a very quick one. Is there any physical limitation to how many ARP entries a 6509 and sup720 can have?
View 4 Replies View Relatedif it is possible to recover a Cat 6500 that has no code on bootflash from ROMMON, and is it mandatory to have a compact flash card to do the recovery ? or can one use xmodem or TFTP ?
View 6 Replies View RelatedI'm trying to boot this IOS on a 6506-E, s72033-adventerprisek9_wan-mz.122-33.SXI8.bin.
This is what I see in bootvar.
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Standby not ready to show bootvar, I want to remove SXF8 and leave SXI8 alone. I removed both IOS file names in boot system and added the SXI8 again and saved. So this would be the output after.
But after a switch restart, this would be the output of show bootvar again.
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Is there anything I need to check? This is an old engine and I'm not sure if the variables of the RP modified .