Cisco Switching/Routing :: Sup720-3BXL Stuck On SP
Mar 19, 2013I have a SUP720-3BXL that will not boot. It will get stuck at booting from the SP. It never switches over to the RP. [code]
View 5 Replies
ADVERTISEMENT
Cisco WAN :: SUP720-3BXL / Using Of ECC Or Plain Memory?
Dec 7, 2010i know that Sup720-3BXL has been used the SDRAM.but i don't know that which of memory? using of ECC or plain memory?if use the plain SDRAM, how can prevent to parity error?
View 1 Replies View RelatedCisco WAN :: WS-SUP720-3BXL And WS-X6748-GE-TX Configuration
Feb 20, 2013I have the above config in a 6509-E chassis with X2 Cac-3000 psu's
The problem i'm having is when everything is powered up it runs fine for about 10minutes then reloads the switch,The 6748 has a 6700-CFC installed the only way i have managed to get it run without crashes is to remove the 3BXL card from the sup and replace it with a PFC-3B, whilst this has solved the problem the client wants the 3BXL card to be installed, am I right in thinking that the CFC installed on the 6748 is incompatible with the 3BXL or maybe the 3BXL is faulty
Cisco WAN :: 7613 - Redundancy With WS-SUP720-3BXL Module
Mar 20, 2012We have Router CISCO7613,SSO redundancy configured with two Sup 720-3BXL running 12.2(33)SRC1 image. Even thought I've configured SSO, my standby sup remains in COLD state with the following logs generated.
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:07:32.514 IST: %ISSU-SP-3-PEER_IMAGE_INCOMPATIBLE: Peer image (c7600s72033_sp-ADVENTERPRISEK9-M), version (12.2(33)SRC1) on peer uid (8) is incompatible
Mar 20 22:08:48.263 IST: %PFREDUN-SP-4-INCOMPATIBLE: Defaulting to RPR mode (Runtime incompatible)
[code]...
These logs says that due to some reasons, the configuration is not being synchronized with active and standby sups and hence the redundancy mode remains in RPR mode and SSO not achieved, and hence COLD state. However, I couldn't find a reason why the configuration is not being synchronized, I've issued the command, redundancy config-sync ignore mismatched-commands, and everything worked fine, SSO achieved and standby sup came to HOT state.Now my query is,
1. Why the configuration was not synchronized and standby SUP got in COLD state??
2. Since I issued the suggested command, at least, some of the mismatched lines in configuration will be ignored, Will that create a problem when my Active sup fails and standby become active?
Cisco Switching/Routing :: Is It Better Take 6724 With DFC3BXL Then Only S720-3BXL
Jan 22, 2013We have 7 interfaces with rj45 connections.. all around 100Mbit per connection .. most likely in the future we will need a couple more interfaces.. i was thinking it would be better to take a WS-X6516-GE-TX card then a FE card as for example a WS-X6148-RJ-45 .Now we want to implement a 7606 with a SUP720-3BXL with 1GB dram for the RP(MSFC3)... so enough memory to support the 2x a FULL BGP table to two peers.
Q : Does the SUP720-3BXL work well with two peers sending the FULL BGP table ?
Q : And does that also work with a WS-X6516-GE-TX connected to the two peers sending the FULL BGP table ? .. or is it better to take a 6724 linecard with a DFC3-BXL so that the 6724 will lookup routes locally instead a 6516 will have the S720- perform the routing ? I know that adding the DFC's increases the bandwidth of the chassis significantly (40gbps per slot most 6700 linecards ,and 20gbps for the 6724 which is 1:2 oversubscribed )
Q: Or is it better to connect the two peers to the two SFP interfaces on the SUP720 , and connect the small routers and customer networks to the 6516 linecard?
Cisco Switching/Routing :: How Many Session Can Use In Sup720-3b
Aug 30, 2012I will use function of span in sup70-3b.How many session can use in sup720-3b? For example, 2 or 4 session.
View 1 Replies View RelatedCisco Switching/Routing :: Need To Know Serial Number Of Sup720
Dec 10, 2011How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies View RelatedCisco Switching/Routing :: SUP720-3B Internal Flash
Dec 1, 2011I have received a sup720-3B from Cisco with an internal 512MB flash(sup-bootdisk). I want to verify what IOS image is on the disk and do not have an spare 6509 chasis. Can I remove the 512 MB flash disk and insert it to my disk0: on my production 6509 with the sup32 that the 720 will repplace and view what is on the disk without corrupting?
View 7 Replies View RelatedCisco Switching/Routing :: MLS Statistics On Cat 6500 With Sup720
Sep 11, 2012when using "show mls statistics" I see a lot packets are getting L3 Processed. Does that mean they are getting software-forwarded?
IOS is 12.2(33)SXI5.
Cat6k#show mls statistics
Statistics for Earl in Module 5
L2 Forwarding Engine
[Code]....
Cisco Switching/Routing :: Downgrading IOS On Sup720 VS-S720-10G?
Oct 26, 2011I got a new VS-S720-10G it had 122-33.SXH8b on there. I had to downgrade it to 12.2.33.SXI1 to match our other switches. I installed the file I use in all the other switches, s72033-adventerprisek9_wan-mz.122-33.SXI1.bin but the Sup is now is only booting up only to ROMMON mode.
Initializing ATA monitor library...
Self extracting the image... [OK]
Self decompressing the image : #################################################
################################################################################
################################################################ [OK]
%SYSTEM-1-INITFAIL: Network boot is not supported.
System Bootstrap, Version 8.5(4)
Copyright (c) 1994-2009 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code]....
How do I get the older version of IOS to load up?
Cisco Switching/Routing :: 6500 - Replace Sup720 In VSS
Nov 16, 2011I have problem with the standby supervisor in 6500 vss and need to replace the supervisor. I have follow how-to on the cisco web site url...
But when i boot the new standby sup720 it comes active and both supervisors is rebooting. I wonder if i can do the replacement without rebooting both active and standy supervisor.
Cisco Switching/Routing :: 6509E - Installing And Setting Up Second Sup720
Feb 27, 2013Trying to find documentation on the proper procedure for installing a second sup720 into our 6509-E chassis for sup redundancy. I have found documents that tout how 'cool' and 'awesome' NSF/SSO, and all that is, but haven't found any docs on installing a second sup720 into a chassis that is currently in production and is only running one sup720. In all the years that this chassis has been out, there must me a documented procedure out here to explain this.I have been through the following pages, and have found nothing to this effect.
View 1 Replies View RelatedCisco Switching/Routing :: Configuring MWAM With Sup720-3B In 6506-E?
Nov 29, 2011problem to configure MWAM. I have installed MWAM module in 6506-E slot 2 with sup720-3B. After installing MWAM the Status is PwrDown. I tried to turn on the power but its not happening. MWAM is installed in slot 2 and here is the result of show module 2 My Sup720-eB IOS image is s72033-advipservicesk9_wan-mz.122-33.SXJ1.bin
6506-E#show module 2
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
2 3 MWAM Module WS-SVC-MWAM-1 SAD081203GK
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
2 0003.feae.bb8c to 0003.feae.bb93 3.0 Unknown Unknown PwrDown
Mod Online Diag Status
---- -------------------
2 Not Applicable
Cisco Switching/Routing :: 6513E What Current IOS Version Should Run On Sup720
Jan 23, 2012We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies View RelatedCisco Switching/Routing :: SUP720 - Unable To Boot From Disk0
May 26, 2012Customer is using SUP720 with SP rommon image version 8.1(3), he is trying to boot the new ios image from disk0, but he gets invalid magic error. he fomat the disk0 but still he gets error when he boots from disk0. He suspect that it can't be flash problem but can be software of hardware as he has two flash with same issue on 2 switches.
Customer wanted to recreate, I tried in the lab, i was able to load from disk0, but sup in lab had 8.5(4).
Customer wanted me try with 8.1(3) version. But i was unable to downgrade the SP Rommon image. SP rommon is running in Gold region and I loaded the 8.1(3) from both disk0 and sup-bootdisk, even preferrence was given to region1 but still sup came up with gold region itself.
* Will i be able to downgrade from 8.5(4) to 8.1(3), if so, what are the steps.
* is there any limitation or bug where 8.1(3) will be unable to read disk0.
Cisco Switching/Routing :: 6509 - Maximum ARP Entries On Sup720?
Jan 13, 2008Just a very quick one. Is there any physical limitation to how many ARP entries a 6509 and sup720 can have?
View 4 Replies View RelatedCisco Switching/Routing :: 6500 With SUP720 Recovery From ROMmon
Jan 24, 2007if it is possible to recover a Cat 6500 that has no code on bootflash from ROMMON, and is it mandatory to have a compact flash card to do the recovery ? or can one use xmodem or TFTP ?
View 6 Replies View RelatedCisco Switching/Routing :: 6506E - Sup720 BootVar Not Shown
Jun 4, 2013I'm trying to boot this IOS on a 6506-E, s72033-adventerprisek9_wan-mz.122-33.SXI8.bin.
This is what I see in bootvar.
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Standby not ready to show bootvar, I want to remove SXF8 and leave SXI8 alone. I removed both IOS file names in boot system and added the SXI8 again and saved. So this would be the output after.
But after a switch restart, this would be the output of show bootvar again.
sh bootvar
BOOT variable = disk0:s72033-adventerprisek9_wan-mz.122-33.SXI8.bin,1;disk0:s72033-ipservicesk9-mz.122-18.SXF8.bin,1;
CONFIG_FILE variable =
BOOTLDR variable =
Configuration register is 0x2102
Is there anything I need to check? This is an old engine and I'm not sure if the variables of the RP modified .
Cisco Switching/Routing :: Safe Harbor Versus Sup720
Mar 11, 2012Cisco Safe harbor, I came nto know this can be a replacement for Sup 720.
View 2 Replies View RelatedCisco Switching/Routing :: IGMP And QoS On CAT6500 Platform With SUP720 Engine
Mar 27, 2013I am having problems with IGMP and QoS on CAT6500 platform with SUP720 engine.The problem is, it seems that all IGMP packets are getting marked with DSCP 48 when sent out of the switch regardless of any input service policy. I found several articles saying that PFC QoS does not apply to IGMP packets. However in IOS 15 that should be possible, but I didn't get it to work there either. [code]
View 0 Replies View RelatedCisco Switching/Routing :: SUP720 / Performance Increase From 30mbps To 400mbps
Jan 21, 2012Supervisor Engine 720 options support centralized forwarding rates up to 30Mbps and distributed forwarding rates up to 400Mpps. I never understood the claim of forwarding rate logic in mbps. How i can load the 6509 box to check this forwarding rate?How can the performance increase from 30mbps to 400mbps? is this just because of DFC on all the line cards if yes does it mean i have to add the DFC on SUP as well .
View 3 Replies View RelatedCisco Switching/Routing :: Is WS-SUP720-BASE Supported In 6509-E Chassis
Nov 29, 2010I have a heck of a time finding this kind of information on the cisco site...Is the WS-SUP720-BASE line card a fully supported module in the 6509-E chassis?
View 4 Replies View RelatedCisco Switching/Routing :: WS-F6K-FE48-AF (WS-X6148-21AF) Support With SUP720-10G
Jun 14, 2012Running WS-F6K-FE48-AF InlinePower daughtercards with SUP720-10G?
The release notes mention that the following daughtercards are supported:
WS-F6K-GE48-AF
WS-F6K-48-AF
[URL]
But, specifically, the WS-F6K-FE48-AF is not mentioned.
We need to upgrade the supervisor in multiple 6500 chassis full of WS-X6148-21AF modules with WS-F6K-FE48-AF daughtercards, and we want to make sure there are no compatibility issues.
Cisco Switching/Routing :: 6500 - Upgrade From SUP720 To SUP2T With New Chassis?
Apr 28, 2013We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
The requirement is we would like to replace these switches with minimum downtime.
Cisco Switching/Routing :: IOS Latest Stable Version 6513 With Sup720
Mar 29, 2012I have Cisco 6513 with sup720 running s72033-adventerprisek9_wan-mz.122-18.SXF8.bin. I would like to upgrade with the latest and stable IOS.
View 5 Replies View RelatedCisco Switching/Routing :: 6509 - Upgrade Sup720 To Sup2T In VSS Cluster
Jun 21, 2012I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
Cisco Switching/Routing :: Different Netflow Export Profiles On Cat 6513 With Sup720
Aug 28, 2012Is it possible to have one netflow export profile (may not be the right word...) to send all the flow information to one collector and another profile to only send traffic to and from centain IP addresses to another collector? If it is possible on the hardware and software, any quick sample config?
#sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH4,
#sho module 7
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
7 2 Supervisor Engine 720 (Active) WS-SUP720-3B SAL1115LJBR
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
7 0017.9444.9814 to 0017.9444.9817 5.3 8.4(2) 12.2(33)SXH4 Ok
Mod Sub-Module Model Serial Hw Status
---- --------------------------- ------------------ ----------- ------- -------
7 Policy Feature Card 3 WS-F6K-PFC3B SAL1115L2NH 2.3 Ok
7 MSFC3 Daughterboard WS-SUP720 SAL1115LH7W 2.6 Ok
Mod Online Diag Status
---- -------------------
7 Pass
Cisco Switching/Routing :: 7606 Sup720 With MSCF / Upgrade To 122-33.SRE6 Fail?
Mar 25, 2012I faced with problem while i was attemping to upgrade CISCO7606 (R7000) from 12.2(33)SRE1 to 12.2(33)SRE6.
rommon 2 > boot c7600s72033-advipservices-mz.122-33.SRE6.bin
Loading image, please wait ...
Invalid device specified
Booting from default device
Initializing ATA monitor library...
string is bootdisk:c7600s72033-advipservices-mz.122-33.SRE1.bin
[code].....
Cisco Switching/Routing :: 6509 Redundant Sup720 - Slave Boots Into ROMmon
Oct 24, 2012I'm fairly new to networking and need to migrate an old core to a new core. I have a 6509-e Switch that I had an RMA on one of my 720 sup cards. After receiving the sup card I swapped my slave out with the new one, expecting it to boot into ios. It booted into Roman. I tried to boot the image manually and it did the same thing. I also tried to boot from my flash and, again, booted into ROMmon.
Question: If i configure and change the boot to boot from image it tells me i need to reset or power cycle first. Will this reset the entire switch? As this is production I'd rather not.
I am at home now, but I can supply any logs/hardware model/configs tomorrow. I thought I would see if this is an easy fix.
Cisco Switching/Routing :: Web-sense Security Gateways Connected To 2x 6500 SUP720
Dec 8, 2011I have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies View RelatedCisco Switching/Routing :: Sup720 / Command To Force Config-sync If Running In Mode Other Than SSO
Aug 9, 2012I am looking to replace the active supervisor (S720-10G) on our 6509E running in SSO mode. The new module already has the same IOs version as the standby supervisor.Once I have swapped the module how do I know that the config has sync'd correctly other than checking the logs? Is it a case of looking at the "Redundancy Mode (Operational)" state and ensuring is says SSO?Also, is there a command that will force a config-sync if it is running in a mode other than SSO?
View 1 Replies View RelatedCisco Switching/Routing :: 6509 SUP720-3B / Dual Link With Failover And Redundant Configuration?
Feb 24, 2013I have a two fiber connection from our Central Office(6513) to Remote office (6509). I have a requirement that on the remote office if one of the fiber goes down, the second fiber should work as a failover. I am planning to use SUP720-3B SFP to connect to the CO.
Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G5/2? or Can I connet one fiber to Sup720-3b G5/1 & another fiber connection to G6/2? I am running EIGRP between sites. Any sample config.
sup-bootflash:s72033-pk9sv-mz.122-18.SXD7b.bin"
Cisco Switching/Routing :: 6509E / SUP720 (Standby Hot) - Console Port Indicate Software Crash
Oct 28, 2012I have one Catalyst 6509E chassis and two SUP720. The bootup sequence on SUP 720 (standby hot) failed . Messages that appear on SUP 720, on the console port indicate o software crash. I don't have a flash card in SUP720.
This is the bootup process:
System Bootstrap, Version 8.5(3)
Copyright (c) 1994-2008 by cisco Systems, Inc.
Cat6k-Sup720/SP processor with 1048576 Kbytes of main memory
[code].....