D-Link DIR-655 :: Missing Serial Number?
Jun 10, 2012
I'm based in the UK and am using a DIR-655 router but I have no record of its serial number (there is no sticker on the item, and the original box is now missing) - is there any way I can ascertain which version of the router I have? As I understand matters, I need to know this so that I can apply the correct firmware upgrade, which is what I wish to do.
View 1 Replies
ADVERTISEMENT
Sep 29, 2011
i have LMS 3.2 installed in my campus. i need the serial number of the LMS suite to open a service request with cisco. but unable to find the same. How to find the same.
View 1 Replies
View Related
Dec 11, 2011
How to get Ciscoworks LMS 4.0.1 serial number ? I need that to put the product under mainrtenance, and I can't manage to get it.
View 2 Replies
View Related
Mar 1, 2012
What is the equivalent oid as chassisid - .1.3.6.1.4.1.9.3.6.3.0, which gets the serial number for most cisco switches/routers is for the ASA 55XX series firewalls.
View 2 Replies
View Related
Apr 17, 2013
I need to get the serial number of SFP in WLC 5508 ver 7.0 but can't find the command, is this possible and if yes how can I get the S/N of SFF in WLC?
View 4 Replies
View Related
Feb 8, 2009
We are running WCS 4.2 on linux. I need to find the serial number of the software so I can raise a TAC case. how to find the serial number? I cant see it via the GUI.
View 10 Replies
View Related
Feb 25, 2013
just ran a discovery on a large network and found 49 wireless controllers (5500, 4400 and 2000 series) and none of them are showing the controller serial number. They are all running 7.0.235.0 and I found no bugs that match this issue.
View 1 Replies
View Related
Dec 13, 2011
i need the address of my pro 900 series printer to install the program for my Sony note pad
View 2 Replies
View Related
Dec 10, 2011
How can i find the serial number of sup-720 which is totally dead and not boot?By which sticker on SUP and where ? How many digits ?
View 4 Replies
View Related
Nov 24, 2011
I have a problem with an AP1310 which may need me to open a case for RMA. is there any way I can view the serial number using the GUI since the AP is already installed on a high mast but I didn't enable telnet on that?
View 1 Replies
View Related
Oct 16, 2011
I have about (12x) AS 5350 XM installed in a remote site. I would like to know their serial numbers (the one on the sticker outside the AS) I know that this SN begins with JMX and contains 11 characters. When tel netting those AS, and type the following commands : show inventory, show hardware, show version, show diag.. i can't find those serial numbers. I can find others which begins with JAE !
View 3 Replies
View Related
Sep 27, 2011
How can I find the serial number at Cisco PIX-515E ?
View 2 Replies
View Related
Jan 4, 2012
My Sony Vaio was stolen and I dont have any tracking software on it. I was told it can be traced using the serial number this is not going to work as the serial number is not digital is this correct? If so is there any inbuilt device or software ect: that comes installed when you purchase the laptop? I am desperate to find my laptop as it has personal information stored on it of my partner who recently passed away and non of this is replaceable. I would prefer to find it without using the authorities as i know who this person is i just dont know where this person has stored the laptop. It would be best for the authorities not to be involved for my safety.
View 5 Replies
View Related
Jul 9, 2011
My laptop "hp pavillion dm4-1065dx" hass been stolen and i have not installed any theft or tracking related softwares. Kindly tell me how to work dis out and find my laptop.
View 1 Replies
View Related
Mar 21, 2012
Is there a CLI-command to see the serial number of the flexstack module installed in a C2960S.
View 13 Replies
View Related
Jun 27, 2004
Im trying to determine the serial number of Gbics already installed and running on a Catalyst 2950 switch. Is there a specific command to do so? There is a command on Catalyst 4506 that gives all info regarding the Gbic ("show idprom interface gi 1/1") Is there something equivalent for 2950?
View 4 Replies
View Related
Oct 17, 2011
I am trying to come up with an inventory report of all our 3750v2 stack switches, but for some reason I could not get the serial number of the member switch under each stack. Can Ciscowork LMS 3.2 see the serial number for each switch under a stack?
View 2 Replies
View Related
Oct 24, 2011
I have a faulty ASA5520 and I am not sure if I have a SMART net contract for it or not (I manage over 200+ ASAs). The problem is that the Serial Number sticker that is normally on the back of the ASA is missing. The ASA5520 is also faulty and doesn't power on so I cannot boot it up and run 'show ver' or similar. If I open the chassis there appears to be other Serial numbers on the Power Supply, and Motherboard etc but they do not seem to be the correct Chassis serial number i.e not in the right format, and if I put them into the Trade tool I get no results.
There must be another record of the serial numbers besides 1x sticker to the rear of the chassis that can fall off? How I can get the chassis serial when the device isn't booting. or (Cisco) is there a way to find the chassis serial number from the power or motherboard serial?
View 4 Replies
View Related
Jan 22, 2013
This is the second one of the new ASA 55.5X series appliances where I have seen this issue:When I SHOW VERSION, I can see the serial number displayed. However, this does not match the serial number from the sticker affixed to the outside of the chassis.This makes it confusing on opening TAC cases and for updating licenses.
View 8 Replies
View Related
Jun 5, 2013
Where on the case is the serial number located? I have a dead one that needs RMA.
View 1 Replies
View Related
Feb 10, 2013
I recently moved to another room as I was removing my router I removed some tape unbeknown to me it also removed my MAC Number. Is there anyway I can recover that Mac Number?
View 1 Replies
View Related
Oct 25, 2012
I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
View 5 Replies
View Related
Feb 21, 2012
I have a switch WS-C3560G-48TS.The version of IOS is:
WS-C3560G-48TS 12.2(58)SE2 C3560-IPSERVICESK9-M
The command "track number rtr" is missing. There are just three options there:
#track 10 ?
interface Select an interface to track
ip IP protocol
list Group objects in a list
Why is that so and where is rtr?I have the same switch with the following ios version:
WS-C3560G-24TS 12.2(50)SE1 C3560-IPSERVICESK9-M
rtr is present in there.
View 2 Replies
View Related
Apr 23, 2013
Any good way to force a serial link to delay packets to simulate a hi latency WAN link? Found this command so far:
Router(config-if)# transmitter-delay hdlc-flags
I can dial the speed up/down via clock rate all good but I need to also simulate latency. This is for simulating a WAN bonding scenario so I was going to aggregate a 10M ethernet port with a 2M serial and a 512k serial. But I need to also ensure varying latency.
View 2 Replies
View Related
Mar 3, 2013
Region : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
View 1 Replies
View Related
Jan 15, 2013
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : AT&T
Everything seems to work fine except that there is no Wireless option in the menu. I updated the firmware and reset to factory defaults, but the wireless option still does not appear in the menu.
View 1 Replies
View Related
Apr 9, 2013
I've been trying to connect two DCS-942L to some netgear WNHD3004 (wireless access points a/n WPA2 personal) that I use as access point but I can't find them in the site survey (advanced settings then wireless setup in the camera page).I think I could set manually the network name, security mode and key but since I'm working remotly on these camera, I'm pretty sure it won't work and I'll loose connection (actually they are connected to other access points and work ok).An ipad and macbook pro is able to see and connect to these access points so I don't think they are the problem.I've updated the camera to the latest firmware (1.12 build 1608 agent version : 2.0.15-b11)
View 2 Replies
View Related
Feb 4, 2013
I have had a DIR-655 for years, and this is a treat - channeling everything from IPTV, to a fast fiber connection, transfers - no sweats.
Then I had to setup a router for a friend, and recommended the DIR-615.
Setup the router, and max it would connect with was 150mb - I changed the settings accordingly: auto channel scan channel width: auto 20/40mhz
So this "opened" up the 300mb speed - however only for 5 mins, then it falls down to 150mb.
My laptop (lenovo) connects to the dir-655 just fine at full speed, and this is also the machine I used for testing the dir-615.
It's ax Hx firmware, FW: 8.04
What I can conclude by using inssider, and xirrus wifi inspector is that it generates 2 channels - and then after 5mins of connectivity looses a channel, and then the speed drops.
I got a new router from the dealer, same issue. Then a friend of mine lent me an ancient dir-615, and interestingly enough this had the same configuration option of "Transmission rate" in the wireless settings page! Just like the dir-655. and also connects at 300mb...
View 5 Replies
View Related
Nov 28, 2012
Region : Others
Model : TD-W8901G
Hardware Version : V6
Firmware Version : 6.0.0 Build 120213 Rel.30335
ISP : ETAPA
I am writing in from Cuenca, Ecuador. I have a TD-W8901G Wireless ADSL2+ Modem Router. I have accessed the interface using the default ip address:192.168.1.1.When I select Interface Setup from the menu, it only shows Internet and LAN as the only 2 options. Wireless is no longer there. It just disappeared! The LED indicator light for WLAN is also "OFF." When you try the Quick Start wizard guide, it cannot complete the setup because there is an IP address error.
I have changed the firmware 2x since, trying to remedy this, I have also tried factory resets at least 3x. Nothing has worked up to this point.
View 1 Replies
View Related
Apr 9, 2013
I keep getting disconnected from the game "Vindictus". I'm not sure what protocols it uses, but it shouldn't require any configuration on the Router, since it was working fine before. I upgraded the firmware to 4.13 in an attempt to fix the issue, but it didn't work. Some people have suggested "Endpoint filtering" to be set to independent, but I cannot find such an option. Where is the option? I was told it was on the Firewall page, but it is not there (Advanced->Firewall/DMZ). The router is supplied by Virgin Media (ISP) but I'm not sure if that matters.
View 6 Replies
View Related
Nov 17, 2010
I just purchased two DCS-930L cameras. They are both installed and running fine over wireless. I can view them via a web browser, however, I cannot get D-ViewCam to work. I installed the latest version (3.1.1). As soon as I launch the Main Console it crashes and I get the "Missing or Corrupted Files error code 268435457". I saw the other post in terms of change the display settings on my PC to 1280X768, however, that does not work. I also have User Account Control (UAC) turned off.
View 7 Replies
View Related
Jan 12, 2011
How do I configure a data T1 serial link on a router using IOS 15 and a VWIC3-1MFT-T1/E1 module. The "interface serialx/x/x" are not there anymore?
View 1 Replies
View Related
Mar 4, 2011
For our children, we use the parental control feature of the DIR-615 (RevD, FW4.11b15), which works excellently. I use the whitelist feature, so only trusted web sites can be accessed. Unfortunately the DIR-615 only has 10 entries in that list and I will soon need more. So I wonder if there is another D-Link router that offers a bigger list with maybe 50 or even 100 entries?
View 4 Replies
View Related