D-Link D-ViewCam :: DCS-930L Cameras Missing Or Corrupted Files
Nov 17, 2010
I just purchased two DCS-930L cameras. They are both installed and running fine over wireless. I can view them via a web browser, however, I cannot get D-ViewCam to work. I installed the latest version (3.1.1). As soon as I launch the Main Console it crashes and I get the "Missing or Corrupted Files error code 268435457". I saw the other post in terms of change the display settings on my PC to 1280X768, however, that does not work. I also have User Account Control (UAC) turned off.
I have installed two 930L cameras which work fine via mydlink. When I attempt to connect them to D-View Cam 3.11 they fail to connect or will not stay connected.I first tried connecting to the router with both cameras in the same room as the router. One will connect and stay connected but the other will connect and freeze or not connect at all. If I move th GOOD camera out of the room, it will not connect.Do I have a router issue? I am using Verizon FIOS with their supplied router (Actiontec, I think). My wireless laptop connects but signal strength is never 5 bars.
i have multiple DCS-930 and DCS-932 at my home. I also have other IP cameras. Is there a way to add IP cameras to the mydlink app on Android, iPad, and web?
I am doing a project with 6 DCS3411, 4DCS 7110 and 1DCS 7410. My question is which DNR /NVR will be able to support all the cameras and how. because most of the say they can support up to nine.
i have this problem when using Remote Live Viewer the Web Remote Client of DviewCam 3.2: i can only see one camera at a time, even more i have to stop playing the current one if i want to change the camera. the viewer shows me the grid for playing many cameras but i don't know if they can be played simultaneously. I can select any camera and will play so i don't think it's an access problem.
I have (2) 942-L, and (1) 5222-L on one network. port forwarding set on router; (942) 192.168.1.3:1024, (942) 192.168.1.4:1025, and (5222) 192.168.1.8:80. no matter if all 3 are connected to dViewCam, only two will work at a time. Disconnect any third, and they work fine. reconnect 3rd, and one disconnects intermittently. On a side note, if I run a different program on another computer (iMac); i.e. IP Camera Viewer, they all work fine. I know, I know, but I like DViewCam, because it's the only thing running the PC computer.
Downloaded DVIEWCam 3.0. Are there any plans on supporting older Dlink Cameras like the DCS-2100 etc ...? Even my DCS-3220 is not fully supported, however the 3420 worked in the config menu.
I can access my cameras through the Dlink web site (mydlink), but cannot access all of them through D-View Cam o n my desktop. I do a camera search and it only finds two of them and the third one it doesn't see. I tried to insert it manually and it still doesn't see it. It sees it fine in mydlink.
I've uninstalled the D-View Cam program and re-installed it, with the same results.
Setup my DCS-930L for DDNS (Dynamic Domain Name Server) so I can access the DCS-930L via the Internet (couldn't access the camera half the the time while on vacation using mydlink) and can now access the camera using my laptop, Android Thrive, and Motorola Droid 3 via the URL I've created but can only see the video when using the laptop.
I have the DCS-930L set to Java but when I log into the camera with the Thrive or Droid 3 (both Android devices) I don't get video. I can make changes to the camera settings and everything else you can do when logged into the camera but just can't see the video. If I change the 'View Mode' in the video setup to 'Image', I will get a picture on all three devices (Thrive, Droid 3, and laptop).
What do I need on the Droid 3 & Thrive so I can see the video when I log into the DCS-930L with an Android device?
Just replaced my SMC Gateway with a Cisco Home Networking Modem, router doesn't see DCS 930 cameras. Working perfect before. I start the wizard, I plug in camera power, plug in ethernet cable for setup, light is green as requested, searches for camera, comes up "No Cameras found". Called ISP provider to reset modem, still no go. Tried a wireless setup using the "buttons", no go. Reset cameras..
I am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
I have a Gaming Computer, with a 2x2TB RAID-1 setup, which I use to store .iso files ripped off my game's / movie's disks..Most of the time I'm on my laptop, I have set up a Network Drive to this RAID-1 setup, but when I try to transfer files from the Gaming Computer to my laptop via a network connection, either by wireless G, Ethernet 100mbps, or Ethernet 1gbps, my files get corrupted, this usually happens to larger files e.g over 1GB..But when I transfer the same files to my external hard-drive the files work properly....My computers is networked by a TP-Link 340G....
I'm using a Verizon DSL router, Mac D-Link Camera Setup Utility (BETA), and Mac OS X 10.6.7. Configuration of camera is as recommended in manual with CAT-5 cable. Green light blinks irregularly in a communicating-with-router manner. The setup utility won't recognize the camera
I have been using FrontPage 2003 successfully and recently as of 2 days ago...I wanted to edit the website and the files are ALL missing. UGH!!!! Its very frustrating that I cannot edit the website now and we are missing valuable information. I did see the files when I created a new Network Place with the prefix but I cannot edit and save to our website. Now I did ask MyHosting administrator but they are seriously taking longer to get back to me then needed. I can open Front Page, but of course, cannot publish anything to the website. More so, even just opening the files in server.com is the actual issue because I cannot change the website page. That's the files I need to change in Front Page. I did go to my account settings within myhosting server to the File Manager and YES! I could see all the files....but again I cannot save anything to the website or publish..I DID NOT DOWNLOAD anything over the past few days and have not gone to unauthorized websites that would have provided a virus. Everything else works fine.
Newly acquired DIR-615 E3 with F/W vers. 5.10. Router configured with IPv4 static address for WAN works fine. As soon as I configure the WAN IPv6 with a static IP address also, the configuration for the IPv4 static IP is corrupted. Other combinations of (WAN config) using static for either IPv4 or IPv6 with DHCP or other seem to work. Just appears to have conflict with two WAN static IP configurations.
Region : Malaysia Model : TL-WR841N Hardware Version : V7 Firmware Version : 3.12.7 Build 110726 Rel.37868n ISP : unifi
as I tweeted here: [URL] The top download from [URL] is corrupt.
Took my ages to find that I need to post in the 300Mbps Wireless Routers forum to get support with the TL-WR841N. All the little subgroups are a little over-engineered to say the least.
I'm keen to improve the performance of this router. It needs rebooting and Apple based clients need to reconnect all the time.
Region : UnitedStates Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
I can view numerous other PDF files from other websites, and even PDF files from TP-LINK, but, the User Guide for the TL-WDR3600 or the 3500 error out when opening in a web browser. If I right click and download them, they will download but then error out on opening.
I would like to start a new thread on possible enhancements/improvements on the new D-ViewCam v3.0.Allow Events (General Motion detection) to be visible in Playback timeline/period selection, similar to the way of Backup (and Remote Playback) timeline/period selection. Fixed in 3.01.Allow 30-second steps increments forward/ backward in playback. Current minimum is 1 minute.Allow jump to event during playback, from either log-viewer or inside playback (via extra button), similar to version 2.0xMention 64-bit compatibility in User- documentation/ datasheet (it is not there yet)Allow/implement multi-channel simulcast [remote] Playback (it is pre-wired) Allow/ implement multi-channel remote viewerBug: Fix Signal Lost event visibility in time/period selection (it does not show these events)Bug: Fix 64-bit hi-res (>1280x1024) "Resource" error. Fixed in 3.11.Bug: Fix Playback.exe crash when saving image/snapshot, while supplying wrong extension (reproducible by: Save as jpg, then supply name.asf, and it will die)Road_runner: Option to move app-window/screen to other monitor and/or resizeToppy: Support older model cameras (DCS-900/950)Toppy: Support multi-screen display (multiple windows)disaster: Option for a playback list similar to V2.03, select motion separately, instead of single stream.disaster: Allow for GUI to select cross-mignight period (can be done manually by setting start-date and -time)disaster: Elaborate more on Smart Guard in Docsdisaster: Allow for higher free space percentage threshold for overwriting old recordings disaster: Allow to program autopatrol to start and end on a scheduled timeBug: Use of < character in password causes deletion of ALL defined remote serversZippyDan: Remote Live Playback: playing video from more than one camera at the same remote site at the same time.
My Brother-in-law, who lives in Singapore, uses his DCS-2121s (2x) for monitoring his newborn and it works great!
Me and my wife, who lives here in the US, always views those IPcams through my web browser from my PC (firefox 7.1).
I was just wondering if there is a different way to watch those cameras using my computer. I was looking for a dedicated D-link APP or Program so I don't have to use the browser anymore.
I have a setting where we are using some DCS930l cameras connected to a 2003 server. We are using the remote viewer and can see one camera but not the others. We have 5 cameras. We try to drag and drop the other cameras, but nothing shows up. Only the 1.
Is it possible to configure a 3rd party product with D-Link D-Cam View program? We want to combine three D-Link IP cameras DCS-2210 with a epiphan VGADVI Broadcaster (url...). The epiphan product can provide a http mjpeg video stream that can be displayed with a normal Webbrowser, VLC or other programs like that.I can connect to the broadcaster with this URL...
I have just purchased 3 DCS-932L'S and installed 3.11 D-ViewCam software. I have done my best to configure the mainconsole correctly so that my cam's will record on motion based occurances on a weekly schedule of 24 hours a day everyday. I have a lot of evidence that the system is recording as when I have the console open that there is motion detected and there are 3 folders in my nas unit that has tons of .dat files in them. My problem comes in when using the playback system. When I select the search by date/time button and locate the folder that is for a the camera I am interested in playing video for the results never show up!
I have a DCS-932L camera setup in my living room with motion detection activated in DView. During the day it works great, but after nightfall the camera shows random lines in the [poor] video. These lines are being picked up as motion and as such the camera records all night long taking up massive amounts of disk space. Even when I put the camera motion detection on 'lowest' value, it still picks it up.
I have 3 DCS-932L connected to DviewCAM 3.3 Device pack 1.4.2. When I open the DviewCAM main console I have picture. When I activate network service (live streaming) options under port: 8080 and webserver port: 801, it allows a visual of the DviewCAM GUI but no live streaming over the internet. [code]
I having issues with DView 3.11 on a WinXP Professional with SP3.There are 4 DCS 5300G cameras wired to the router.I can see the cameras using IE, but when I try to configure the DView in the camera section with the autodetect button it will show an error that the camera cannot be identified.I had checked the IP address, port, user & pass everything is ok. I even hard reseted one of the cameras and it won't work.
When I view my DCS-932L camera in the Main Console of DViewCam, I can here the sounds in the room being viewed. But if I record the video and play it back, there is no audio on the playback. I have the microphone on the camera enableI now have sound recording, however, the audio is about 3 seconds behind the video. Is there a setting somewhere to keep them synchronized? I have checked all the video sync checkboxes I can find.
Just got this & set it up today. Wanted to buy a couple more in the next few days; but wanted to test out the D-Viewcam service. The application (D-Viewcam) is not able to find my camera.I have 'ticked' the uPNP & the forward; tried to disable it as well. No luck.
Camera 942l is on ver 1.1 D-Viewcam = v 3.2 Both reside on the same LAN
I'm able to view the camera on the browser. And on my phone.
Taking another look at Dview cam today after not touching it for 3 months after initial install.The dcs-2132L can't connect.I can to the 2132L directly... I changed the port as a test.. Port 80 wasn't working originally.
This causes massive 3G data to be used. If you don't close the app first it just keeps streaming and eating data + battery.This data screen cap is for 10 minutes after locking the phone with the app open.When the phone locks, the app should kill the video streaming.
I originally began using my D-Link cameras, two DCS-5300s and a single DCS-6620, with the IP Surveillance software. I see that the software is no longer recommended and may no longer be available. Any explanation for the move to the DView Cam software ? If I were to convert over to DView Cam from IP Surveillance will I lose any functionality or features. Will there be any functionality or features gained ?
