D-Link DIR-615 :: E3 Configuration For IPv4 Static IP Is Corrupted
Aug 19, 2011
Newly acquired DIR-615 E3 with F/W vers. 5.10. Router configured with IPv4 static address for WAN works fine. As soon as I configure the WAN IPv6 with a static IP address also, the configuration for the IPv4 static IP is corrupted. Other combinations of (WAN config) using static for either IPv4 or IPv6 with DHCP or other seem to work. Just appears to have conflict with two WAN static IP configurations.
View 11 Replies
ADVERTISEMENT
Mar 16, 2012
We set up three new terminals this week at the office; they're all running Win 7 Pro 32-bit. I set them all up simultaneously (literally sat at a desk and entered the same keystrokes at each of them), so I don't see any obvious reason that one is behaving differently from the other two. The essential problem is that the terminal doesn't see the Internet.
Here are all the particulars that I think might be interesting, listed in no particular order:
- The terminal ran fine for several hours. Email access, Internet access, from 9 a.m. to 2 p.m. At that point, the user called me to show me a dialog box. I used System Restore to go back in time to 9 a.m. in case the user had somehow managed to do anything (though she's not an admin).
- IPv6 is disabled.
- The workplace uses Static IPs. The IP address is entered correctly in the IPv4 properties (x.x.x.213), but at cmd / ipconfig, I get this result: "Autoconfiguration IPv4 address: 169.254.95.187"
- In Network and Sharing Center, the network (which is only known as Unidentified Network) is set to type Public. When I reset it to type Work and reboot, it resets to type Public.
View 1 Replies
View Related
Dec 7, 2011
ASA 5520 running 8.2
Is it possible to do static (inside,outside) with the outside address being IPv6 and the inside IPv4?
If yes, is it possible to do this in parallel with an existing static mapping that goes IPv4 to IPv4?
View 3 Replies
View Related
Feb 29, 2012
I live in a shared house, and I am the only one who has been experiencing issues connecting to the internet. I have to ask a housemate to reset the server, as this is the only thing that works.
When I am unable to connect, and I use command ipconfig, the following appears: Autoconfiguration IPv4 169.254.23.29 On the occasions when I am connected, the following appears in its place: IPv4 IP Address: 192.168.0.2
One tip that I came across was to check the box (Wireless Network properties, Connection tab) for "Connect even if the network is not broadcasting". I had hoped this simple solution would assist, but to no avail.
View 5 Replies
View Related
Mar 30, 2012
Last two weeks, I have had a problem connecting to public hotspots. My own WiFi network is fine, but while I am connected to any public hotspot I get the 'no internet access' message on the wifi symbol.While connected to my own network, ipconfig/all shows that I have an Autoconfiguration IPv4 address in the (correct) 192 range - but when connected to a hotspot, the address is in the 169 range, or occasionally (as in the instance below) in the 10 range. Clearly this is the problem, but I cannot figure out what has caused it. Is it hardware? Software? Malware? Or user error?I have run the Wireless Test and the log results are pasted below.
Windows IP Configuration
Host Name . . . . . . . . . . . . : XPS-CLIENT-TIM
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 14 Replies
View Related
Oct 31, 2012
Region : Malaysia
Model : TL-WR841N
Hardware Version : V7
Firmware Version : 3.12.7 Build 110726 Rel.37868n
ISP : unifi
as I tweeted here: [URL] The top download from [URL] is corrupt.
Took my ages to find that I need to post in the 300Mbps Wireless Routers forum to get support with the TL-WR841N. All the little subgroups are a little over-engineered to say the least.
I'm keen to improve the performance of this router. It needs rebooting and Apple based clients need to reconnect all the time.
View 1 Replies
View Related
Nov 17, 2010
I just purchased two DCS-930L cameras. They are both installed and running fine over wireless. I can view them via a web browser, however, I cannot get D-ViewCam to work. I installed the latest version (3.1.1). As soon as I launch the Main Console it crashes and I get the "Missing or Corrupted Files error code 268435457". I saw the other post in terms of change the display settings on my PC to 1280X768, however, that does not work. I also have User Account Control (UAC) turned off.
View 7 Replies
View Related
May 8, 2013
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I can view numerous other PDF files from other websites, and even PDF files from TP-LINK, but, the User Guide for the TL-WDR3600 or the 3500 error out when opening in a web browser. If I right click and download them, they will download but then error out on opening.
View 10 Replies
View Related
Feb 17, 2011
I have a Gaming Computer, with a 2x2TB RAID-1 setup, which I use to store .iso files ripped off my game's / movie's disks..Most of the time I'm on my laptop, I have set up a Network Drive to this RAID-1 setup, but when I try to transfer files from the Gaming Computer to my laptop via a network connection, either by wireless G, Ethernet 100mbps, or Ethernet 1gbps, my files get corrupted, this usually happens to larger files e.g over 1GB..But when I transfer the same files to my external hard-drive the files work properly....My computers is networked by a TP-Link 340G....
View 4 Replies
View Related
Mar 24, 2013
Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..
Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...
View 3 Replies
View Related
May 16, 2013
I currently have ipV4 as the setting on my DIR-825. Other posts seem to want ipV6 which is more secure but is not possible with a DIR-825 Rev A1. I have two routers, a primary router (DIR-825 Rev B1) capable of ipV6 and a secondary router (DIR-825 Rev A1). If I implement ipV6 on the Rev B1 router but keep ipV4 on the secondary router, will this improve the security, or will it just mess things up so nothing works?Certain devices (cell phones and most Tablets) don't deal with ipV6 very well at all. The ones I have tested flat don't connect to the wireless network if the router is set at ipV6. Is ipV4 adequate for a Home/Small Business Network when trying to implement Remote Access and VPN?
View 2 Replies
View Related
Jun 9, 2011
I have a Dlink DIR-825 B1 with firmware 2.05NA. I recently reset it to factory defaults to make sure I didn't misconfigure something.
I have been struggling to get a IPv6 in IPv4 tunnel working with tunnelbroker.net. I think the issue is a problem with the router itself and i'm not sure how to get it fixed.
All of my machines were getting IPv6 addresses (both windows, mac, linux) but none of them seemed to work. All I was able to do was ping the gateway itself using the local lan address. In each case they were missing a default IPv6 route. If I added a default route then it would work.
I started looking at the packets using a network sniffer and the Router Advertisements all had a Router lifetime value of "0" which is RFC4816 speak for "don't use this router as the default router". So Windows/Linux is exactly right by not setting a default route.
The strange thing was that when I reboot the router I would briefly get a router advertisement with a lifetime of 1800s, the corrert prefix and dns server but then another router advertisement would come along 5 seconds later with a router advertisement of 0.
I have TCP' Other observations
... using 6to4 I would get working IPv6 address. The difference again seemed to be the Router Lifetime. But I want to use a permanent tunnel. I have found 6to4 unreliable.
... the router never responds to router solicitations. It only sends a router advertisement when it wants to.
... the router never responds to DHCPv6 when that is configured.
View 1 Replies
View Related
Jul 2, 2011
I'm connected through a simple non-configurable switch to a 172.20.0.0. 255.255.0.0 network, with a gateway of 172.20.2.2.
When i use DHCP, i am able to connect to the web.
When i change my ip address to a static address (with an available ip address and correct subnet mask and default gateway) i am unable to connect to the web.
View 7 Replies
View Related
Sep 3, 2012
I ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , the traffic dynamic crypto can not be used since traffic may be initiated from Dc on other link which may get dropped incase not encrypted.
View 5 Replies
View Related
Feb 25, 2012
I have a router manufactured by AirTies,the model is Air 4450.This has the capability of being an Access Point in a current network, which is how I want to use it. (Introducing it into my current Sky Broadband network with a Sagem F@ST 2504N router).However, I cannot access the configuration page whatsoever.The manual states the default IP address of the router is 192.168.2.254, so I have set my laptop to a static IP of 192.168.2.100 and patched into LAN port #1 on the rear of the Airties 4450, powered on the unit and cannot access the router at all.I have held down the reset button several times to no avail.how I can configure this unit ?
View 2 Replies
View Related
May 11, 2012
I have the cisco 1841, where I am trying to put the static routes on it, it does execute the route commnad but does not show the static route
Below is the out come
lab_router1(config)#ip route 192.168.1.24 255.255.255.248 fas 0/0
lab_router1(config)#ip route 192.168.1.32 255.255.255.248 fas 0/1
lab_router1(config)#exit
[Code].....
View 18 Replies
View Related
Feb 8, 2012
I have configure 887 ADSL router with attached configuration. But users cant access internet properly. (Ex: yahoo and gmail mail cant access)
View 8 Replies
View Related
May 21, 2012
We are replacing our EOL Watchguard X1000 Firewall(s) with Cisco ASA 5510 unit - ASA Version 8.4(3). Following is the static NAT I have build and the corresponding access list.
nat (FW2Inside,FW2Outside) source static BW_XSP1_Private BW_XSP1_Public destinat
ion static BW_XSP1_Private BW_XSP1_Public
access-list FW2Outside_access_in extended permit tcp any object BW_XSP1_Public object-group DM_INLINE_TCP_1
Unable to access the server on the inside interface via the public NAT address. Can you point me in the right direction as to what I might be missing to make this work?
View 1 Replies
View Related
Apr 17, 2011
I'm having some issues configuring NAT statements on my ASA5505 which has recently been upgraded to 8.41.
I have a single dynamic IP on the outside interface of the ASA and would like all internal hosts to NAT/PAT to it. In addition, I would like to have several ports 'forwarded' to internal hosts, one of which is TCP/4343. With the current configuration all hosts are NATing to the external interface properly but the service running on TCP/4343 is not accessible from the outside. See command output below:
"sh run object" output:
object network DrJones host 10.81.220.90object network LAN-10.81.220.0 subnet 10.81.220.0 255.255.255.0
"sh run nat" output:
object network DrJones nat (inside,outside) static interface service tcp 4343 4343object network LAN-10.81.220.0 nat (inside,outside) dynamic interface
"sh run access-list" output:
access-list inside_access_in extended permit ip 10.81.220.0 255.255.255.0 anyaccess-list outside_access_in extended permit icmp any any echo-replyaccess-list outside_access_in extended permit tcp any interface outside eq 4343
View 6 Replies
View Related
Feb 20, 2012
We have 2 sites with 2 internet connections at each site. All are SRP527w routers. 1 is for internet and 1 is for a site to site VPN as,Currently we are using Static Routes on the PC's so they can access each server no matter what site they are at. I have looked at using the Static Routes section on the SRP's but cannot get it to work.
View 2 Replies
View Related
Jul 27, 2012
Purchased the RVS4000 in 11/2012 to work behind a NVG512 in (pass thru mode). I'm running firmware version V2.0.2.7. For whatever reason once or twice a month I lose access to the internet. Sometimes it's AT&T fault but other times my RVS4000 dosen't behave well. I finally took screen shots of every screen I configured in the RVS4000 to make it work in my environment. Last night we lost internet access again. Before unplugging everything I looked in the RVS4000 and found that my WAN setup had reverted back to a default Automatic Configuration - DHCP instead of the Static IP that I had previously saved.
It seems that my RVS4000 is losing just that WAN setting (port forwarding and Static IP Mapping data and VPN client data is still intact.
View 6 Replies
View Related
Jul 30, 2012
I'm experimenting a strage issue with some AP1142 that prefer getting new IP from DHCP server rather than using the static ip already configured.
I've got more than a hundred of 1142 APs already conected to a 5508, all with static IP, all working fine for about a year.
As i installed 30 more AP, i enabled a dhcp scope on the controller to give IP to the new APs and when the new aps got registered i changed the configuration to static IP.
The problem comes when some of the older AP than have already static ip are gettig ip from dhcp scope.
If i look at my WCS, it reports that this APS are getting DHCP IP because they cannot reach the controller with their static ip. As this is impossible, because the static ip and the dhcp enable scope are in the same subnet in a layer 2 configuration and with the same gateway. (e.g: old AP 10.10.2.10/16; new AP(dhcp 10.10.3.10-50) 10.10.3.15/16; gw 10.10.254.1)
The problem comes when i disable the dhcp scope, all the older aps that got dchp ip from the wlc scope instead of using their staic configured ip are deregistered. If i reset every ap manually, from the swithc disabling PoE, they start to use the static ip and everything comes fine.
This is happening with about ten of fifteen APs from the 100 installed, that is the strange thing because this seem to be very random as the failing APs are installed in different building and connected to different switches.
As now i have disabled dhcp scope and all APs (old and new) have static ip everything is ok, but i will have to add some more APs shortly and every time i enable the dhcp scope on the wlc
View 8 Replies
View Related
Mar 25, 2012
Very recently whenever I download a file which is in a package e.g. a rar file or an iso it always seems to be corrupt. For example I downloaded the windows 8 consumer preview multiple times and each time was corrupt. Now I know it isn't anything to do with my computer as I have this problem on all devices connected to my internet including my ps3, every game I download is corrupt and I cannot install it. I've tried all the obvious things like turning the router on and off and plugging the device directly into the router via ethernet
View 1 Replies
View Related
Dec 4, 2011
How do I create static smartport macro on Catalyst 2960 & 3750 equivalent to below static smartport macro:
macro name NOT_USED
description UNUSED_PORT
switchport
switchport mode access
switchport access vlan 100
shut
@
I am able to create above smartport macro on Catalyst 3760 & 6500, but not on 2960 & 3750 (see below):switch(config)#macro ? auto Macro autoexecution settings global Enter global macro configuration
View 12 Replies
View Related
Apr 1, 2011
half of my laptop driver are corrupted (network, USB, and sound). I had installed a program called 'motion joy' and play with the software... right after i reboot my laptop, the sound icon and the network icon on the system tray are crossed out. I can see yellow exclamation mark on the drivers icons on device manager.
I made an attempt to roll back those corrupted drivers but nothing happen. Even when i try to update it, it says i had the latest driver. ;( I tried to uninstall the driver but the those driver files at 'system32/driver' are still there. I even tried to run driver CD that comes along with my laptop, and when I run the installer, it states that all the drivers are install.
so bascially now my laptop boot, run program BUT can't access internet , all USB ports are unavailable,and no sound at all.
View 5 Replies
View Related
Sep 25, 2012
I have an Averatec 1550H laptop. The wireless card driver was corrupted so I replaced with a driver from Trigem. The name of the device is an Intel(R) PRO/Wireless LAN 2100 3B Mini PCI Adapter. I can get as far as a message saying a cable is unplugged.
View 9 Replies
View Related
Jun 5, 2011
IOS of my LAP 1131AG is corrupted. It is giving error messages while booting and asks for boot image.
View 2 Replies
View Related
Dec 14, 2012
I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies
View Related
Dec 29, 2011
I noticed my tumblr dashboard was loading corrupted thumbnails. I first thought that tumblr was having problems, until it started happening on my deviantArt, and YouTube. I was worried that it was my computer, but then the same thing started happening on my moms' Macbook, and then her Wi-Fi streaming television started corrupting the video. And then, sometimes a website won't load fully, but will instead load part of it's code, or instead my browser (I've tried on Google Chrome, Firefox and IE) tells me the webpage is unavailable, or doesn't exist. It'll load up semi-properly (with the corrupted images still) after a refresh or two, but it's tiring and worrisome.
View 1 Replies
View Related
Oct 1, 2012
I am getting following error on a Cisco 3845 router intermittently.
000312: Sep 26 15:38:19: %CALL_CONTROL-3-STAT_MEMORY_CORRUPTED: Memory corruption detected in memory=69028FA8 allocated for RTCP statistic
000315: Oct 1 08:26:01: %CALL_CONTROL-3-STAT_MEMORY_CORRUPTED: Memory corruption detected in memory=6902E160 allocated for RTCP statistic
Platform: Cisco 3845
IOS: c3845-spservicesk9-mz.124-24.T2.bin
View 6 Replies
View Related
Dec 7, 2011
I want to upgrade IOS on 1811 from 12.4(11)T3 to 12.4(15)T16.
As a standard CF size in the 1811 is 32 M, so I have to free some space.
Here the strange things starts.
dir issued on the router shows thet ther is no image on the flash!
dir
Directory of flash:/
No files in directory
31940608 bytes total (12771328 bytes free)
sh ver shows that
uptime is 19 weeks, 2 days, 9 hours, 22 minutes
System returned to ROM by power-on
System restarted at 15:21:30 EEST Tue Jul 26 2011
System image file is "flash:c181x-advipservicesk9-mz.124-11.T3.bin"
The other strange thing is that some space is allocated for something!
(flash size) 3194060 - 12771328 (free) = 19169280 (space allocated to ???)
Just now router is running IOS c181x-advipservicesk9-mz.124-11.T3.bin The size of this IOS is 19 155 816, that is approximately equal to the size that allocated to something invisible.
fsck flash and format flash doesn't work. Bug Toolkit doesn't show any bugs similar to my issue.
View 4 Replies
View Related
Jul 6, 2012
I'm finished with formatting my computer to install a clean Windows 7 Ultimate. Then, I connect my PC to the modem I have, to browse the Internet of course. Well, everything runs fine on the first start, let's say I have installed Google Chrome, Microsoft Office, and some other software I still not installed it. And when I restart it and tried to run Google Chrome for example, it said "Google Chrome has stopped working", it's happened to almost every software in my PC, let's say I tried to install VirtualDJ, then the Installer is corrupted, so was the Google Chrome installer and Microsoft Office Installer. Before they are all corrupted, there was a suspicious thing named 'winblmguf.exe' trying to access the Internet through my firewall.
View 6 Replies
View Related
Jan 29, 2011
I corrupted my BEFSR41 firmware v4.2; is there a way to recover?
View 1 Replies
View Related
