D-Link DIR-655 :: Does Auto Configuration Overrides Manual Configuration
Dec 14, 2012
I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies
ADVERTISEMENT
Sep 27, 2012
I am having a public IP address and it is not configured on any of the router interface on my Cisco router. I am having 3 internal networks. Is there any way to PAT all these 3 internal networks to this public IP?
View 3 Replies
View Related
Feb 29, 2012
I live in a shared house, and I am the only one who has been experiencing issues connecting to the internet. I have to ask a housemate to reset the server, as this is the only thing that works.
When I am unable to connect, and I use command ipconfig, the following appears: Autoconfiguration IPv4 169.254.23.29 On the occasions when I am connected, the following appears in its place: IPv4 IP Address: 192.168.0.2
One tip that I came across was to check the box (Wireless Network properties, Connection tab) for "Connect even if the network is not broadcasting". I had hoped this simple solution would assist, but to no avail.
View 5 Replies
View Related
Mar 27, 2013
I configure safari with auto proxy configuration, insert the proxy server name, and click apply.However, if i go to network-tools.com and do a traceroute, the trace does not show the proxy serverin the series of IP address's. I have tried with several different server names but i makes no
View 1 Replies
View Related
Mar 30, 2012
Last two weeks, I have had a problem connecting to public hotspots. My own WiFi network is fine, but while I am connected to any public hotspot I get the 'no internet access' message on the wifi symbol.While connected to my own network, ipconfig/all shows that I have an Autoconfiguration IPv4 address in the (correct) 192 range - but when connected to a hotspot, the address is in the 169 range, or occasionally (as in the instance below) in the 10 range. Clearly this is the problem, but I cannot figure out what has caused it. Is it hardware? Software? Malware? Or user error?I have run the Wireless Test and the log results are pasted below.
Windows IP Configuration
Host Name . . . . . . . . . . . . : XPS-CLIENT-TIM
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
View 14 Replies
View Related
Mar 6, 2012
Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.
View 1 Replies
View Related
Jun 28, 2012
I configured Auto QoS on some access ports on two 4506-E (Sup 6E-L) and I wanted to apply the same generated config on the port channel/port channel members but it didn't work.
Ex:
int gig1/3
service-policy input AutoQos-VoIP-Input-Cos-Policy
% A service-policy with non-queuing actions should be attached to the port-channel associated with this physical port.
[Code].....
View 1 Replies
View Related
May 8, 2013
Are there issues with the auto upgrade feature for 3750X stacks, either historically or currently?
Some people prefer to upgrade switch stacks manually by disconnectiong the stack cables and uprading code on each switch.
I've done the manual procedure in the past and have not tried the auto upgrade (I have the procedure for the auto upgrade).
View 18 Replies
View Related
Jul 17, 2012
I am position to migrate from CatOS 6509 switch to native IOS 6509 switch. long time ago, there was some site to convert automatically based on copy and paste onto the tool, but i can not find.
Does anybody know how to convert CatOS configuration to Native IOS configuration ? It is not IOS change, but it is configuration convert.
View 1 Replies
View Related
Dec 27, 2012
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies
View Related
Mar 9, 2012
I stuck with a DIR-655 so I don't have to re-program all my custom settings.HOWEVER, I am attempting to load the settings file I saved from my A3 into my new B1 and it doesn't work. It says "The restored configuration file has been uploaded in failure". "Press the button below to continue configuring the router".
View 1 Replies
View Related
Sep 12, 2011
set up a wireless network connection? i have a wireless router but cannot access it using my browser?
View 3 Replies
View Related
Feb 22, 2012
Recently i brought D-Link DIR-524 wifi router. somehow i am able to connect to internet. But i am dont know how to block it for other computers. i am new to networking. How to configure the D-Link DIR-524 wifi router.
View 7 Replies
View Related
Sep 12, 2011
Set up a wireless network connection? i have a wireless router but cannot access it using my browser?
View 1 Replies
View Related
Feb 11, 2012
I've a brand new DIR-825 and I've tried to connect my pendrive into a DIR USB.
I configured my router like this:
I've installed software like this:
And this option don't work !
USB led is blinking at blue color and my pendrive is blinking too.
How I configure this ? everything else is working now and my internet too.
View 3 Replies
View Related
Apr 1, 2013
Region : India
Model : TL-MR3220
Hardware Version : V2
Firmware Version : mr3040v2_en_3_14_4_up_boot(121017)
ISP : Railwire
I have an broadband connection which does not need a modem to access, i get the CAT5 inthernet cable from the provider. In case if i use it directly on my PCall i have to do is provide username and password under PPPoE and internet works like a breeze.
Now i try to use this 3040 device to use as an wireless router so that i can access internet on multiple devices. How to configure this. I tried in all the three switch options provided with no result at all..I am now using a traditional router from which i connect to Tplink 3g router and using wireless under Access point option...But i would like to use it directly as i can get battery back up so that even when there is no power i can still browse?
View 2 Replies
View Related
Feb 9, 2012
I just received a DIR-615 in the post that I bought on eBay. I currently have a DI-624 at home .Will I be able to copy the configuration from my old router to this new one?
View 3 Replies
View Related
Aug 17, 2011
I've got the DIR-825 2.02. I had an issue where if you did change the IP adress default 192.168.0.xxx to something like 192.168.yyy.xxx, the configuration page was becoming inaccessible. It was super slow, was displaying the wrong pages with missing images and wrong page formating. I had to reset the router to default and then it was working fine.That seems to have been fixed since 2.05. Now you can change the default ip adress to anything you want and the configuration or setup still work fine.When I am on LAN, the setup page are displayed almost instantly. By remote, it's super slow.
View 1 Replies
View Related
Jun 12, 2009
I have been trying in vain to setup my home network so that I can perform wake on lan (WOL) over the internet. I have been able to do WOL with a magic packet utility within my local network - so I know that the PC NICS are configured correctly - but this does not work when I try it from my office for example, over the internet.
I have a virtual server set up forwarding ports 9 and 7, UDP to 192.168.1.101 initially, but found some threads about using the broadcast address so changed this, but still no luck. I had to downgrade to 1.20 from 1.21 as I found several threads here about firmware versions not allowing broadcasts.
My setup is as follows:
Router: 192.168.1.1
PC1 192.168.1.101 (static assigned by MAC address in the router)
PC2 192.168.1.102 (static assigned by MAC address in the router)
Broadcast address was 192.168.1.255
View 14 Replies
View Related
Apr 4, 2011
Just bought three D-Links from abroad ( Canada) and now am in Mauritius. They are brand new and now going to set them up.
1) DIR-825 H/W : B1 F/W : 2.02NA
2) DNS-323 H/W : C1 F/W : 1.09
3) DWA-140 H/w : B2 F/H : 1.50
I already own a Beetel 220BX2 modem. I will be connecting :
1) my PC through the DWA-140
2) three Samsung Galaxy S
3) One LG phone (b/g)
4) Network Player (Yet to be bought)
5) Laptop
What are the steps to follow (Firmware updates, Configurations). I was planning to do VPN and to have each device have its own IP.
View 14 Replies
View Related
Aug 7, 2012
I am looking after a mixed collection of Cisco and HP switches and use a Perl script to extract configuration data.I use the ifStackStatus table (OID: 1.3.6.1.2.1.31.1.2.1.3) from RFC1573 to sucesfully obtain the EtherChannel data from the Cisco switches but, though I do obtain data from the same table from the Procurve switches it seems to bear no resemblance to Link Agregation. I could look at other tables and may have to - but would like to use this one in order to simplify the code.
View 2 Replies
View Related
Jan 29, 2012
I have been trying to configure some settings on my modem and to do so I must access it from it's ip (192.168.250.1). However, when I load that ip in my browser it does not connect.
My router has a private ip of 192.168.0.1 because of a Double NAT issue which I am trying to fix by going to the modem's configuration page. I am pretty sure that it is 192.168.250.1 because that is what my router ISP Gateway says, along with ipconfig in cmd when I directly connected to the modem from my computer.
By the way, I am currently connected through my D-Link 254 router which is connected to my WiMax modem.
View 2 Replies
View Related
Nov 18, 2011
How do I configure my router to run with my TP-link TL-SF1016D switch. If I connect my switch on my router I cannot have to internet?
View 1 Replies
View Related
Dec 29, 2011
I've noticed that many people have routers with NAT as part of their security configuration. What NAT is/does? Also, I entered the router's settings and went to Advanced > Firewall > NAT ENDPOINT FILTERING .There are 3 options specified for UDP/TCP Endpont Filtering; they are:
Endpoint Independent
Address Restricted
Port and Address Restricted
What are these options? I downloaded the manual for the router but it doesn't mention what NAT, Endpoint Independent, Address Restricted, and Port and Address Restricted are.
Side Note: I thought about setting up a secure connection using WPA2. Right not I'm using an unsecured wireless network. If I setup a new secure wireless connection using WPA2 will my current unsecured connection still be available?
View 11 Replies
View Related
Aug 11, 2012
I've been lagging really bad when my sister uses the laptop upstairs with wireless connection. Just 1 computer makes me have up to 100 ping, imagine 3. How can configure my settings so that i will stop lagging or configure so that i have priority.I have a Dlink 655 Version A4 with the latest firmware 1.35
View 9 Replies
View Related
Mar 15, 2011
What is the name or path for the file stored on your hard drive for the configuration settings?
View 7 Replies
View Related
Oct 11, 2011
I have a D-Link dsl 2640u, it's a modem but since it has 4 ports im assuming it's also a router. My problem is that when i enter my ip address into the address bar it doesn't recognize it. I can't use Utorrent or anything that requires ports to be opened..and it's a pain in the butt. when I type ipconfig on my command prompt it brings up..172.16.X.X and when i enter it into the address bar nothing is found. I'd like to port forward by accessing the modem's config page.I read on another thread that i could set my own ip address by going to: Control Panel>Network and Sharing center> Local Area Network>Properties of Ipv6 and typing my own ip address but when i do this i lose my internet connection.
View 14 Replies
View Related
Feb 16, 2011
I have a Samsung CLP-315W printer wireless that i cant communicate with. I get network printer status not available. I contacted Samsung support and they said to talk to my router manufacture and get the network configuration and enter it manually.
View 9 Replies
View Related
Nov 9, 2011
The day before yesterday, I bought the dir-615.
I had set an admin password and user's password. It was not same password. In this setting, there was no problem. Sure, no problem at connect from private IP, internet IP or just reboot and anywhere. The problem is the next.
If you got an electronic timer-switch and apply the DIR-615 then you cannot obtain an admin privilege from a remote. It just general user's permission even if I put the admin password.
I have been DIr-615 E4 hardware and 5.10 firmware. It does not happens at local IP address(i.e. 192.168.0.1) but it happen as trying connect from a remote IP address after AC plug re-powered.
I am doing use the AC timer for the remote internet managing at every day. It useful things for the router and IP camera. I need a admin privilege from a internet for the router managing.
View 16 Replies
View Related
Feb 23, 2012
I have Broadband 100 from Shaw Cablesystems (100mbps speed).I can only pull 30mbps with the DIR-615. I have tried exchanging it for another one, same issue.Is there some kind of configuration option I'm missing?
View 14 Replies
View Related
Aug 19, 2011
Newly acquired DIR-615 E3 with F/W vers. 5.10. Router configured with IPv4 static address for WAN works fine. As soon as I configure the WAN IPv6 with a static IP address also, the configuration for the IPv4 static IP is corrupted. Other combinations of (WAN config) using static for either IPv4 or IPv6 with DHCP or other seem to work. Just appears to have conflict with two WAN static IP configurations.
View 11 Replies
View Related
Nov 10, 2011
Is it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825? If so, what steps are required?
View 1 Replies
View Related
Feb 6, 2013
I have configured my two vdsl link with ppp multilink but i am not getting the desired bandwidth. Here is my configuration is this okay or i need something more in the configuration. My router is 2921 what is the maximum WAN throughput of 2921? [code]
View 3 Replies
View Related
