TP-link TL-SF1016D Switch Network Configuration?
Nov 18, 2011How do I configure my router to run with my TP-link TL-SF1016D switch. If I connect my switch on my router I cannot have to internet?
View 1 Replies
ADVERTISEMENT
Cisco Switches :: SG300 Correct Configuration For Redundant Link Between Two Switch
Mar 9, 2012I have two switch SG300-10 that need to be interconnect togheter with a simple redundant "cable fail safe" configuration.My idea is use the two uplink copper port of the first switch, connected to the two uplink copper port of the second switch.
How to create a working setup configuration? The first setup that i need, is with only one VLAN1 for all ports,
The second setup is with the VLAN1 assigned to the ports 1-2-3-4 of all the two switch, (linked togheter by uplink ports)
and the VLAN2 assigned to the ports 5-6-7-8 always linked togheter with the same uplink ports.
Is possible use the two uplink port at the same time, as cable fail safe? or use a uplink port 1 for the first group and the second uplink port for second group?
I need to use this configuration for audio cobranet transport, and i need to test the correct configuration for the primary and secondary audio stream, if can work togheter on the same VLAN or i need to separate the two stream, from start to the end.
Belkin Routers :: Surf N300 - Configuration With Lan Switch Through Network?
Nov 23, 2012We have 12 PC connected through a Switch(D-Link 10/100 mbps) with Configtured with Manual IP Address. the IP address range is 192.168.1.1 subnet mask 255.255.0.0 default gateway 192.168.1.1.Internet Cable Connected from Modem to Switch Directly & all the computer access internet by filling DNS with 202.56.224.153 other 59.144.127.17, We fill this DNS only where we want Internet access allowed by limiting that pc with Limited User access. How to configure Belkin Surf N300 Router with this network.
View 1 Replies View Related2960S Skills Of Switch Configuration Are Greater Than Network Design
Jan 5, 2012One of our clients is replacing some of their aging network components with 4 Cisco 2960S switches. Unfortunately in this case, my skills of switch configuration are greater than my skills of network design. I have a really crude network diagram of their basic network layout (4 servers, 4 switches, and a number of endpoints).
How would you experts design the physical connections in such a way as to facilitate some redundancy?
D-Link DIR-655 :: CLP-315W Network Configuration For Printer
Feb 16, 2011I have a Samsung CLP-315W printer wireless that i cant communicate with. I get network printer status not available. I contacted Samsung support and they said to talk to my router manufacture and get the network configuration and enter it manually.
View 9 Replies View RelatedCisco Switching/Routing :: Catalyst 4006 / Quickly Copy Configuration From Production Switch To Spare Switch?
Nov 20, 2009I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedTP-Link 300Mbps Wireless :: TL-WR940N - Network Connection Doesn't Have Valid IP Configuration
Mar 18, 2013Region : Poland
Model : TL-WR940N
Hardware Version : V2
Firmware Version :
ISP :
few days ago i changer my work etc . so i tried to connect to worknetwork wireless but it was connected for 10 minutes and then this message just appear "Wireless network connection doesn't have a valid IP configuration" there is also public network the same ,, connected for few minutes then when i connect again always the said limited access but with my home work is working perfectly but with work or public network always get this msg after few days searching in google nothing useful ps all computers in company are working perfectly with this wireless connection but my laptop no i have this message in router setting WAN port is unplugged,, check photo here [URL] router model TL-WR940N im useing win7 64 hp pavilion dv7 anti virus > deleted firewall state > off IP helper > disabled when i was connecting to public network this is result of Xirrus WI-FI inspector [URL]
TP-Link 150Mbps Wireless :: WR702 Connecting To A Hotel Network With Browser Configuration?
Mar 25, 2013Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am trying to work out how I can use the WR702 to connect to a Hotel's wireless connection. As with most modern hotel setups, the hotel requires the user to access a web browser and enter the room number and select a purchase plan.I believe there must be a way that I can connect the WR702 to the hotel's network and then use a browser on a linked (wireless or ethernet) laptop to launch the browser and log in, however, I have tried every default configuration on the WR702 and cannot find a solution.
Setup:
WR702 router
HP EliteBook 8440p laptop (ethernet and wifi available)
Hotel wifi (multiple identical SSIDs in the survey but shows as a single wifi name on my iPhone)
D-Link DIR-615 :: Connect 2 Wireless Modem Routers + Switch In Home Network
Nov 14, 2011I have 3 pieces of hardware:
1. Green Packet DX-230 WiMAX modem with router
2. D-Link DIR-615 ver G2 (from my ISP)
3. D-Link 8 port desktop switch
I previously used the DIR-615 with my high speed broadband connection. However I had to move to a new house and here I can only get WiMAX. I want to...Place the WiMAX modem upstairs to serve as modem and wireless access point Have the DIR-615 function as the main router and firewall (downstairs) Use the switch to connect all the rooms in my house FYI my WiMAX modem has no connection configurations. I just plug it in and it'll connect automatically to the WiMAX signal. It has 2 LAN ports but no WAN port. From my understanding of networking, I have to turn off DHCP on my WiMAX modem, put it in the same IP range as my DIR-615 (192.168.0.100-199), and disable UPNP and NATPMP. After this I'm stuck.How do I tell my DIR-615 to use the WiMAX modem as it's WAN connection?Should I reserve an IP for the modem in my DIR-615?
D-Link DIR-655 :: Does Auto Configuration Overrides Manual Configuration
Dec 14, 2012I have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedCisco :: Failover Configuration - Allow Primary Link To Fail And Secondary Link To Automatically Pick Up Traffic?
Dec 27, 2012We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies View RelatedCisco :: Faulty Switch Or Bad Configuration
Apr 15, 2013Have two switches configured and running 2 links to each other that are in a port channel. Now, I cannot get the 1 of the ports (Gi1/0/50) to come up at all, I've had the cable tested and replaced SFPs both ends. Switch A is a WS-C3750G-48TS and I believe the problem could be here, the last for GBIC ports, 2 of them we are using as links to Switch B in a port channel. Here is the config for both and the 'show int status' for both.
View 8 Replies View Related24 Port Networking Switch Configuration?
Aug 8, 2011how to 24 port networking switch configuration
View 1 Replies View RelatedCisco Switches :: LAG Configuration On SG300 52 Switch?
Sep 10, 2011I am having an issue with LAG configuration on a Cisco SG300 52 switch. I have connected four Ge ports on the switch to the four NICs of a Dell R710 Server on which I installed Windows Server 2008 R2. Without LAG configured, these ports would forward traffic to and from the Dell server fine.However, if I configure LAG on the ports with LACP enabled, then they would not forward any network traffic. Debugging shows that the ports are up but their forwarding status show N/A. Am I missing any configuration? Can I configure LAG on edgeports?
View 2 Replies View RelatedCisco :: Netflow Configuration On 4510 Switch?
Sep 6, 2012I have a 4510 with sup7e and I would like to deploy netflow on this switch. The network will contain the 4510 switch where there will be 4 blades installed, each blade contains a separate Zone (vlan) . These 4 zones will then trunk upto a firewall via ten gig link over sub-interfaces. There will be an ip address assigned to each vlan on the 4500 switch but there can not be routing enabled between the vlans on the switch.
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ISE & 3750 Switch MAB Configuration
Jan 16, 2013I am writting in response to MAB issue which I noticed a few days ago and I am still not able to undestand what exactly happend. First of all I would like to say that I configured MAB authentication and according to the MAC the ISE configure a VLAN. All worked well: the test computer can change VLAN based on its MAC. The problem appear when I cut the connection to ISE server. Accourding to configuration the switch authorize the new device to VLAN 11 (critical VLAN) That is fine ! When the ISE server is up again I had a configuration which should reauthorize all ports assign in critical VLAN. But why that is not happend ??? It looks as the switch didn't notice that the RADIUS (ISE) was up and working again. [code]
View 1 Replies View RelatedCisco WAN :: Catalyst 2950 - Switch Configuration
Dec 27, 2010I just started configuring my cisco catalyst 2950 switch. Basically im preparing for my CCENT exams my basic configuration is as follows.
-My Laptop is connected to the console port
-I'm connected to the internet via my wireless
-I'm connected to the switch port via my NIC card
Cisco WAN :: 3750 - Move Configuration From One To Another Switch?
May 20, 2013im trying to move the config from an 3750 to 3750 PoE but without using the PoE options.I have allready download the config with tftp and upload it to the 3750 PoE. Now the new config is stored on the PoE switch but some of the old setting are still there. Not sure why, i think the config only overwrite the settings which are in the conf file and the setting which are not in the conf file but enabled on it will stay on the switch.After the upload of the config file I deleted all the config I do not need by hand.They are some settings i can't delete and I don't know why, this are the sittings:
1. each fastethernet port has this option: "no cdp enabled" this entry was no availble on the old switch, is the any possiblity to remove this entry?
2. the same for "no mls qos rewrite ip dscp"
3 and for this one "vlan internal allocation policy ascending"
Cisco Wireless :: 3750 - QoS Configuration In Switch For AP And WLC
May 6, 2013The access swtich is a Cisco 3750 and the Core switch is a Nexus 5000 series. I am configuring the switchport were the AP (3502) and WLC (5508) is connected below:
For AP: interface GigabitEthernetX/XX
switchport access vlan 244
switchport mode access
[Code]....
The WLC is connected to the Nexus switch and it is not accepting the 'mls qos trust cos' command.
Cisco WAN :: QoS Configuration For 3750 Switch WAN Port?
Jul 27, 2011We are using 3750 switches as WAN router facing the WAN cloud. To configure QoS for its WAN port, should I use 'auto qos voip trust" or treat it like a router port and configure class-maps, policy-maps, and attact service-policy input or output?
Because switches have different queuing and dropping methods than routers, auto qos can generate QoS configs that are considered most appropriate for 3750 switches. However the switch functions as WAN router. Maybe it should be configured using router type of QoS with policy-maps and service-policy?
Routers / Switches :: Netgear Switch Configuration JFS516?
Jan 5, 2012how to configure a server with net gear switch . I want to restrict access for a few users and use the netgear switch for file sharing between the small network. its got auto configuration .
View 3 Replies View RelatedRouters :: Older 24 Port Cabletron Switch Configuration
Feb 17, 2011I have an old Cabletron switch i have used for about 8-10 years, it has some vlans set up and i was wondering how i can "talk" to the switch and set it up. I am using this switch in my home on my vast network. is it possible to "reset to factory" or anything without a serial cable? I would like to use snmp of telnet to configure but i dont think it has an ip set up and it is such an old switch I cannot find any info from entrasys.
View 1 Replies View RelatedCisco Switching/Routing :: Switch 3750G-12S-S Configuration?
Jan 2, 2013I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies View RelatedCisco WAN :: VPC Configuration Template With Two Core 6509 Switch
Jan 3, 2013What is the VPC configuration template with two core 6509 switch.Pls find the attachment for Network topology.
View 3 Replies View RelatedCisco Security :: NAC 4.8.1 Invalid Switch Configuration-OOB Error
May 18, 2011i just deployed Cisco NAC version 4.8.1 Virtual Gateway OOB on a LAN envieronment and on a WLAN envieronment, it works fine for some users , they can authenticate via the agent or web page, and then they are redirected to the access vlan, But for some other users in LAN and WLAN , when they try to authenticate via agent or web page the following error appears:
Invalid switch configuration-OOB Error:OOB client "mac/ip" not found.
I tried to find some pattern for the users but it dont match any pattern.
Cisco WAN :: 2948 Switch Configuration To WS C2960 48TC-S
Feb 26, 2013I have a 3com 2948 switch and is needing to put the configuration on a Cisco WS C2960 48 port switch. I am attaching the config to heck if that is correct. I know my IP will need to change to .123
View 7 Replies View RelatedCisco WAN :: 3560 Switch Vlan And Router Configuration?
Feb 10, 2012In our new Head office we have to set up a Network connectivity.Total our office 4 floors.In each floor we kept three cisco 2950 switch.We have L3 switch(cisco 3560) to connect the all the other switch.In our office total 5 departments.we have to create VLan for each departments in the switch.
We want to all user to communicate to each other.We have WAN connectivity in the router(cisco 2900) to connect the other office.First i want know how to physically connect all the swiches and finally with the L3 switch.How to configure the VLAN in both L2 and L3 switch.In our other client office one router to connect the both office.In the router how to configure and which protocol to use to communication.
Ip address:10.10.40.0/22
WAN IP :192.168.214.65/30
Cisco :: WLC 5508 - Configure 802.1 Configuration Commands On Switch
Dec 14, 2011How to, for the most part, setup 802.1x via wireless. I'm using two 5508 WLCs, and Cisco ACS. I will setup the user account/password information via Cisco ACS and User Identity and Hosts. I know from the WLC 5508 web admin tool that I can choose 802.1x in the security parameters. I only have a few question. We have two wireless networks, one is wide open and provides internet access, the other will provide internal access for select users. I am setting up 802.1x on the internal wireless lan. Do I need to configure any 802.1 configuration commands on the switch in order for this to work, if so where would be the locations to do this at? Also, if there is a MAC isolation configuration option I can configure to not allow other hosts on this specific wireless network to communicate with each other?
View 3 Replies View RelatedCisco WAN :: DHCP Configuration On Core Switch 4507R
Jul 9, 2011DHCP configuration on CISCO core switch 4507R switch.With one vlan and multipul vlan both configuration using any ip address range.
View 3 Replies View RelatedCisco Switching/Routing :: 827 - Switch L3 And DSL Router Configuration
May 21, 2013i have floor with 10 users with DATA vlan and VOICE vlan , WIRELESS vlan , my questions :
Basement floor Core switch fiber -----> my floor switch <--------my internet DSL router827
- In this scenraio the switch in my floor will be as L2 or L3 ?
- What is the configuration it will be in the switch if it is L3 ?
- What is the configuration it will be in DSL router with Subinterfaces for each vlan ?
Any sample for configuration that can work for switch nad DSL router ?
Cisco 3750X L3 Switch Configuration - Not Getting Any Data Coming Through
Jul 2, 2013I have RFID Reader (10.10.63.2 - 255.255.255.240) connected Cat-6 POE to ws-c3750x-24p-s - standard TCP/IP web service app pulling data from the reader every 250msec: I have my app server connect via vlan by ws-c3750x-24p-s IP address (128.1.70.1 - 255.255.0.0) as you can see its on a different sub net;
I can ping the device from the server - although I'm not getting any data coming through: my config are as:
0 [switch 1 provision ws-c3750x-24p-s]
1 [system mtu routing 1500]
2 [ip routing]
3 [no ip domain-lookup]
[code]...
I can ping the device from the server - although I'm not getting any data coming through.
Cisco Switching/Routing :: Set Up Configuration On 4928-10G Switch
Feb 6, 2012I am trying to set up a simple configuration on a Cisco 4928-10G switch running
cat4500-entservicesk9-mz.122-37.SG.bin
All I want to do is to mark all trafic on vlan 3 let's say for this example with dscp af31.
All outgoing trafic to be marked with DSCP AF31.
In pratice If I have 2 laptops connected to access ports on vlan 3. When one laptop pings the other I want to see on the receiving end when I run wireshark the traffic to come marked with DSCP AF31.
Cisco WAN :: 2950 Switch Receive Configuration File From ISP?
Aug 28, 2012At home I have a perfectly working test setup for more than 1 year now , but yesterday we had a power down for about 10 minutes in the whole area , after this power down nothing was working in my network any longer.
My Network is has follow :
ISP(Cable Modem) on FA23 from the CISCO 2950 SWITCH (24 Ports)
ROUTER (ON A STICK) on FA24 from the CISCO 2950 SWITCH
And the rest of the switch is FA1=VLAN 1; FA2=VLAN 2;FA10=VLAN 10
Our home network is connected to VLAN 10 with a IP Range of 192.168.10.x /24 After this power down , I was not able to look into the SWITCH via FA1 , the FIX IP in this switch was 192.168.1.251/24, the ONLY way to get access was via the consol port !!!What a suprice when I connected my consol to the PC , I can see ROUTER_F342 , my router config is called ROUTER1841 and my switch config name is /was called SW24.So it seems that after this Power Down , the router took or received a config from my provider ?!?
I have recovered the the file in the switch + the vlan.dat and now everithing works again.
How can I avoid that this switch receive again a wrong file , I have all the needed files on the products itself and I do not use a TFTP server.
I have atached some screen shot when my switch is starting up , and it seems that the switch receive a IP address from my ISP , I do not know why, in the config file I have given it a FIX IP 192.168.1.251/24 ?!?So it seems that my ISP erase the config file and when the switch is empty ,the swich look for :
tftp://255.255.255.255/router-confg
tftp://255.255.255.255/ciscortr.cfg
Etc ....
Until it find something.
I have tried after a complete recovery to switch off the power again for 10 minutes (ISP MODEM + SWITCH + ROUTER) and I was not able to reproduce the fault.Can it be that due to this power failure in our area that some routers or switches send or broadcast this kind of things ?