Cisco WAN :: 3560 Switch Vlan And Router Configuration?
Feb 10, 2012
In our new Head office we have to set up a Network connectivity.Total our office 4 floors.In each floor we kept three cisco 2950 switch.We have L3 switch(cisco 3560) to connect the all the other switch.In our office total 5 departments.we have to create VLan for each departments in the switch.
We want to all user to communicate to each other.We have WAN connectivity in the router(cisco 2900) to connect the other office.First i want know how to physically connect all the swiches and finally with the L3 switch.How to configure the VLAN in both L2 and L3 switch.In our other client office one router to connect the both office.In the router how to configure and which protocol to use to communication.
Ip address:10.10.40.0/22
WAN IP :192.168.214.65/30
View 3 Replies
ADVERTISEMENT
Mar 18, 2013
I have a 3560 switch with 1 VLAN (VLAN 10) where I need to make ports:
1-10 as isolated (can't contact each other)
11-20 as community (need to contact each other like a normal VLAN)
23 as promiscuous (server that ports 1-20 need to get to)
24 as promiscuous (WAN router where ports 1-20 need to get to and the remote servers).
[Code]...
View 26 Replies
View Related
Nov 27, 2011
I have a cisco 3560 switch set up as my edge router. It is working as my external demarc switch and edge router. It is sitting between the ISP's switch and my ASA firewall. It's a very basic configuration with port 1 set up with a fixed ip and switchport turned off which is connected to the ISP switch. VLAN2 is configured with an IP address and 3 ports, two of which go to different firewalls.
I found that I cannot ping a specific address from the inside interface (VLAN2), but I can from the outside interface Gig0/1. I have a few deny commands in an access list, but they don't apply to the network i'm trying to access, and I haven't had any other inaccessible networks otherwise.
Here's my config minus passwords and full IP ranges. There are two ranges, one with xxx and one with xx. The xxx is set as secondary, but is the one we really use.
Current configuration : 4808 bytes!version 12.2no service padservice timestamps debug uptimeservice timestamps log uptimeservice password-encryption!hostname my-rtr-ext!boot-start-markerboot-end-marker!enable secret 5 !
!!no aaa new-modelsystem mtu routing 1500ip routing!
[Code] ............
View 4 Replies
View Related
Sep 15, 2012
I have 2 locations, at a distance of 600KM.These two locations are well connected by Point to Point L2 VLAN with a speed of 2 MBPS and supported by CISCO 3560G switches.Location A has a VLAN to communicate to the other VLAN at Location B. Location B has also got 3 VLANS which are inter connected with Location A.Now the hardware in one of VLANs in Location B has moved to Location A for obvious reasons.
For further refernce am giving the VLAN IP address here....
Location A
VLAN1 for communicatng to Location B
IP Range 172.20.44.210
Subnet Mask 255.255.255.0
Default Gateway 172.20.44.210
VLAN2 for the desktops in Location A
IP Range 192.193.194.1-255
Subnet Mask 255.255.255.0
Default Gateway 192.193.194.1
[code]....
View 3 Replies
View Related
May 8, 2012
I have an environment of 3 X 3560G of which I have 1st switch-CORE(f0/10) connecting to the VPN router(CE) interface-f0/0. Remaining 2 Cisco 3560's(Access) are connected to Gi0/1 and Gi0/2 on the 1st switch-CORE via gi0/1 . On all three switches I have created multiple VLANs and assigned ports to these VLAN. The switch to switch connection is trunk allowing all VLANs created on all these 3 switches. Now the issue is how I am going to have all these VLANs routed through single interface on the routeri-e f0/0, as all these subnets will communicating to remote site over VPN. What should be default gateway on the 2 Access switches and the CORE switch, also what static route should be on router to reach all subnets(VLANs) created on these 3 switches.
I have read inter-VLAN routing i-e creating sub interfaces on router but dont want to proceed with that and looking for any other way to have my VLANs talk on all three switches and then are accessible to remote site ove VPN?
View 9 Replies
View Related
Jul 5, 2012
I've recently purchased a Cisco catalyst 2960S-24TS-L & setup 3 V LANS 10 (no current IP),20 (192.168.2.1) and 30 (192.168.3.1) to reflect the router V LAN configuration & ip information. When connecting my PC to the switch to test connectivity on (2.1 & 3.1) I'm unable to connect to the the net but can successfully ping GW (int FE0.20 & FE0.30) 192.168.2.1 & 3.1.
The router is an Cisco 1801 & it seems this is where the configuration issue is but I'm unable to figure out how to complete the setup. It has been quite awhile since I've configured a Cisco router.
Ive never had this router connected to a switch so all router switch ports are in the default VLAN1 (192.168.1.2), with FE0 disabled. In trying to get the switch to communicate with the router I made the following router config modifications.
FE0 enabled with subinterfaces configured
FE0.10-currently no ip
FE0.20-192.168.2.1/27
FE0.30-192.168.3.1/27
I have two issues I want to resolve:
1) I do not know what additional steps are required to allow 2.1.& 3.1 V LANs to access the net.
2) I want to disable VLAN1 if possible & use the network IP for VLAN10 (192.168.1.0). I'm unsure how to do this as any change on VLAN1 immediately breaks router access and the router reconfiguration becomes more complicated with changes to the FW ACL etc.
View 2 Replies
View Related
May 18, 2013
I am configuring 802.1X in a 3560 Switch, my Radius server is a Microsoft IAS, when I connect a station of a guest user, the guest-vlan is not assigned in the port, and I have these logs:
May 8 21:23:02: dot1x-ev:Received an EAP Timeout on FastEthernet0/8 for mac 0000.0000.0000
May 8 21:23:02: dot1x-ev:dot1x_guest_vlan_applicable: Guest VLAN not
[Code].....
View 7 Replies
View Related
Apr 17, 2012
We have over 30 Cisco 3560 switches and over 10 VLANs on our network. In our example, VLAN 10 on switch IP 10.0.20.150 works fine and VLAN 10 on switch IP 10.0.20.24 doesn’t work. The below are both switches show vlan. url....I can’t tell what causes the problem and how to fix it. VLAN 10 on Switch 10.0.20 24 doesn’t work. [code]
View 8 Replies
View Related
May 26, 2013
how to recover password and retrive configuration on Cisco switch 2950 and 3560.I know the way to press and hold the mode button and then plug in the power cord can reset the switch to factory default but it will reset everything to nothing. As such, it is not what I want and I want to keep the configuration file and able to use the configuration on the switch.
View 2 Replies
View Related
Mar 6, 2013
I have a 2911 router connected to a 3750 switch. I have configured vlan interfaces on the 2911 router:I am using the vlan 89 (89.2) as the management ip address for me to remotely get to the switch. Is this a proper configuration or could this cause issues in the future.
View 4 Replies
View Related
Dec 12, 2012
We have a 24 port and 48 port 3560 E switches with identical IOS the 48 port switch supports private vlan while 24 port switch doesnt
configure private vlans on 24 ports 3560e and is it best practise to configure private vlan on this platform(3560)?
IOS version : C3560E Software (C3560E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
flash:/c3560e-universalk9-mz.122-55.SE3/c3560e-universalk9-mz.122-55.SE3.bin
View 3 Replies
View Related
Apr 12, 2012
provide a sample Voice Vlan configuration for the Cisco 2960 POE switch to work with the Non-Cisco IP Phones?
Will these commands work? Vlan 2 is the new voice vlan, Vlan 1 is the data vlan.
mls qos
interface fastethernet 0/1mls qos trust cos switchport nonegotiateswitchport mode trunkswitchport trunk encapsulation dot1qswitchport voice vlan 2priority−queue outspanning-tree portfastspanning−tree bpduguard enable
vlan 2name voice
View 2 Replies
View Related
Jan 10, 2012
Between our hosting and a customer we have an extended vlan, traveling on a fiber, between two cisco 3560 switches.The thing is, that we want to create one or more vlans inside that extended vlan, in some way if possible?
View 3 Replies
View Related
Aug 12, 2012
We have 6509 VSS with FWSM Module and we have created two context on it, one is INTERNALL CONTEXT othe is EXTERNALL Context? We have spanned various VLANS in switches and FWSM context level. All VLAN Gateways are configured in context level.
Activity description : We had planned migration of these devices into a new Datacenter, it was a planned activity. During migration of devices from one Dc to a new DC we broke the VSS and kept the primary running and removed the secondary switch and migrated this secondary to new DC and powered this device ON in the new DC and checked all the config was very much fine but this device was OFF network as secondary was brought to new DC just to limit the downtime during the primary switch movement.
During the activity ( Primary switch movement )We powered off the Primary switch and mean time before shifting into new Data center We had brought up secondary switch which was already existing in the DC was put live in the network and it was working fine without any issues.
Later we had moved Primary into new data center and tried to put into VSS with the secondary , during this period the secondary device into went into RECOVERY MODE and primary device was not responding and devices went off network and immediatly we removed the VSL link and brought up primary into production network without secondary online in the network ( Without VSS just stand alone switch ) network started working, but bringing up the primary we found that some of the VLANS in the FWSM was deleted and some VLAN had misconfiguration ( example : say original VLAN ip 10.200.112.1 has become 10.300.13.1 ) also some of the access list as well as SVI was deleted making configuration mismatch.
Wanted to know while syncronization b/n primary and secondary switch in VSS if we pull out VSL link would create this type of issues.
View 1 Replies
View Related
Nov 18, 2011
I have a Cisco network on a ship where I work, I have an Ericsson GSM Access point which picks up local GSM 3G signal and broadcasts it onboard. I have two of these units and they are connected to a D-Link Load balancing router which is in turn connected to a Cisco 3560 Series 8 poe switch. Each unit is on a different subnet. The Cisco is on the DHCP server from my AD server (Windows 2003 Server) The Load balancing router has no DHCP and the Ericsson units have their own DHCP servers.On the Cisco switch if I plug in with a laptop I get an IP address for the DHCP on my server. I cannot ping the load balancing router from it. If I connect to the Load balancing router and set a static address for that subnet I can access the internet via the Ericsson units. And if I connect to the Ericsson I can access the Internet.
View 22 Replies
View Related
Jul 23, 2012
I have a cisco 3560 24PS and its connected to two ADSL broard band routers.one is a personal broadband line using a Billion ADSL broadband router, and the other is a business broardband line using BT's 2wire broadband line.on the Billion routers i have various things attached like a NAS and a printers, both wired connections. then i have laptops and phones that connect over wifi, so its configured to act as a DHCP server
the only thing conncted to my 2wire router is my company's laptop (wired or wifi depending on where i'm working from), so again i have it working as a dhcp server.The switch is configured with multiple vlans, with dhcp scopes assigned for each vlan.I have a static route pointing all traffic to my Billion ADSL for internet connectivity.
The problem i'm having is that when i turn on the cisco switch, all wifi conected devices loose their conection. only 2 things get it working again, a reboot of the router, or disabling then enabling the DHCP service on the router.upon further analysis i was able to find out that the devices were not able to pick up an address from the router. again i looked deeper into this and i can see the following on logs of my router: [code]
so it seems that the router tuns off its DHCP capabilities because it detects that my Cisco switch is running DHCP services. I need to figure out how to keep the billion routers DHCP running when ever the switch is turned on.is there a way of filtering out any DHCP chat from the switch to the router?
View 7 Replies
View Related
Jun 28, 2012
I have a problem, i would like todo MACSEC betwwen two switches cisco catalyst 3560-x but I know that for this operation i needed ACS server 5.1 is it possible to encryp dataflow without ACS server and if you have the configuration
View 7 Replies
View Related
Feb 26, 2012
what's the meaning of the output:
Interface Speed Local pair Pair length Remote pair Pair status
--------- ----- ---------- ------------------ ----------- --------------------
Gi0/40 100M Pair A 2 +/- 4 meters Pair A Normal
Pair B 2 +/- 4 meters Pair B Normal
Pair C 2 +/- 4 meters Pair C Short
Pair D 2 +/- 4 meters Pair D Short
From the command
test cable-diagnostics tdr int gi 0/40
It's normal?If not, then. the problem is on the cable or on one of the interfaces?The interface is connected between a fastethenert on a 2811 router and a 3560-48 switch.The cable is a straight through cat 5e cable. (I have changed several cables with same result).
View 4 Replies
View Related
Apr 15, 2013
I have a 2 cisco switches that are at different sites one is a Cisco CAT4500 and other 3560. The connection between the switches is a layer 2 fibre link. CAT4500 and 3560 both have VLAN interface ip addresses in order for me to connect to the switches.
I have PC A connected to CAT4500 and PC B connecting to 3560. All these devices are the same VLAN and in the same subnet. I do have trunk links all the way though allowing this vlan as we run vlans. From PC A, I can ping CAT4500, 3560 and even PC B. This tells me everything is fine regarding Layer 2 & 3.
As soon as I move PC B and connect it to the other switch CAT4500 or move the other PC vice versa (this happens in both directions). Both switches learn that the mac address has moved locations and updates its mac address table accordingly. So when I do a show mac address table and show arp, everything has learned and moved fine. However when I try to ping any other device from PC B I cannot. So the 3560 switch PC B was originally connected to, I can no longer ping, the switch cannot see the pc also. It is as if PC B has not learned anything from the switch and cannot respond or reply to any icmp. I have tried this with different end devices, same thing. I am now thinking it has something to do with the switch.
View 14 Replies
View Related
Jan 10, 2013
I have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
View 4 Replies
View Related
Jan 24, 2013
configuring a switch or a router to limit the bandwidth for a specific user/IP when need it. Most of my remote offices are configured like this:
Users ------ 3560 switch ------- 2801 router -------- T1 to NOC -------- 7204 router with channelized DS3
I use Netflow Analyzer for high bandwidth usage alerts and can see the user's IP right away when someone is clogging our T1s. My goal is to be able to temporarily limit the bandwidth of the user taking over the T1. Whatever is best switch config or on the router.
View 2 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
Jan 10, 2012
Is it possible with a 3560 to block all traffic to a certain vlan except for one or two IP addresses? Create an ACL or something? We have a vlan for voice calls (SIP) and we are getting a lot of scnas that are making the phones ring and such, and I think we can stop this if we only allow traffic onto the vlan from the IP's the SIP traffic is SUPPOSED to be coming from.
View 1 Replies
View Related
Apr 10, 2011
We had a new building thats gone up and complete now and we're trying to get a ip phone working down that end of the school on a vlan. We seem to be having trouble with the VLAN going through on the 2960 switch but it works fine on our core 3560 switch.
There looks like a slight variation in the config of the switches, the 3560 switch supports the "switchport trunk encapsulation dot1q" command on the interface where as the 2960 doesn't support the "switchport trunk encapsulation dot1q". Is this why the vlan is working on the 3560 and not the 2960, or is it something else?
Both switches are using the 12.2 IOS
Heres the trunk port configured on the 3560 going down to the new building and connecting into the 2960 with a 1gbit fiber link
interface GigabitEthernet1/2 description 3560X Port UpLink as Trunk Mode switchport trunk encapsulation dot1q switchport mode trunk udld port storm-control broadcast level 60.00 spanning-tree guard root
Heres the trunk port configured on the 3560 going to a Linksys switch which then connects to the DHCP server (The other end of the 3560 is also configued as trunk)
interface GigabitEthernet0/6 description Edge Switch port for clients switchport trunk encapsulation dot1q switchport mode trunk spanning-tree portfast
Heres the working vlan port on the 3560, the ip phone is able to get an ip and ring all other phones etc
interface GigabitEthernet0/7 description Edge Switch port for clients switchport access vlan 2 switchport mode access spanning-tree portfast
Ok now heres the config for the 2960
Heres the trunk port configured on the 2960 going back upto the 3560 switch
interface GigabitEthernet1/0/25 description Port UpLink as Trunk Mode switchport mode trunk udld port storm-control broadcast level 60.00
Heres the access port configured on the 2960 which isn't passing on vlan information. Is there another command i need to use to enable encapsulation as dot1q?
interface GigabitEthernet1/0/19 description Edge Switch port for clients
switchport access vlan 2 switchport mode access spanning-tree portfast
View 11 Replies
View Related
Dec 5, 2011
Is there any way to check if this VLAN is used by somedevice?
Cisco3560#sh ip int b
Vlan55 unassigned YES NVRAM administratively down down
Cisco3560#sh vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active
55 Print active Fa0/5, Fa0/6, Fa0/7, Fa0/8
View 18 Replies
View Related
Dec 7, 2011
I want to give a breif overview of the current setup and what I had planned to do in the future. This is also where a few questions come into play. Currently we have 3 10.x.x.x subnets between three buildings with a wan connection. This connection is invisible to us so it can be seen as just a lan. The speed is 100mb. We have a 2811 router sitting at each building translating their traffic back to 10.3.1.1. We then have a router in the main building which ships the 10.3.x.x traffic to a ASA and then out the door to a ISP.
My plan was to upgrade this 100mb WAN connection to 10g fiber between our buildings as they are in extremely close range of each other. I would need a equipment upgrade as a 2811 won't support 10g traffic. Rather than replacing 3 routers in each of the buildings it seemed logical that I could get something like a catalyst 4500 or 6500 and do int vlan routing making it all one huge campus lan. Creating a vlan for each building to segment the traffic between them. My understanding was that a cat 3500/4500/6500 did not need a router with sub interfaces in a one arm setup to bridge this traffic. This is where the problem comes in.I tested with a cat 3560 and was unable to get the vlans to route correctly. Do I have to have a router to get int vlan routing to work? If so then I might as well get a Router which can handle multiple 10g fiber for the core instead of a cat 4500/6500 since I'd need the router to do the int vlan routing anyway?
View 17 Replies
View Related
Jul 22, 2012
I have 4 vlan and all has conectivity/access with all (VLAN10,VLAN20,VLAN30 and VLAN40, I use a 3560 Switch for this propose, I need to modificate one vlan (VLAN40) that has access to the rest of the VLAN's BUT the rest of the VLAN's dont have access to VLAN40. I know that it is a problem of access-list BUT I can't undertand how to obtain the result that I like
View 1 Replies
View Related
Jan 15, 2013
My first question is I have an access layer switch which is a single VLAN and I am trunking that VLAN to a distribution layer switch, I can ping the gateway on the distribution layer switch for THAT VLAN, But cannot ping the gateway address for the second VLAN I have on the distribution layer switch. I know it is simple, But I have forgotten and just need a push
Also I have a third VLAN set to route traffic not bound for those 2 VLANs out to a router is the statement "ip route 0.0.0.0 0.0.0.0 172.16.252.2" good enough and do I actually need to create a VLAN for that traffic? and if so, is an access switchport the best option?
View 2 Replies
View Related
Sep 29, 2011
I have no router inplace that can do trunking (5505 basic license )I have 2 VLANS 10 Data 20 voice I have given both VALNs IPs lets say
-VLAN10 192.168.1.1
-VLAN20 192.168.2.1
Enabled IP routing and set the router as the gateway of last resort.Now becuase the L3 switchis doing the routing I have had to set the default gateway as the VLAN IPs. So PCs on VLAN10 get a gateway of 192.168.1.1 and phones on VLAN20 get a gateway of 192.168.2.1
Any real downside to having the 3560 doing the VLAN routing, is this the "correct "way to do things in the event I don't have a trunkable router?
View 8 Replies
View Related
Jan 16, 2013
Topology: 3560 <-access-mode-link-> ASA5510 - Internet,3560 has 3 VLANs and 3 corresponding SVIs (default-gateways for VLANs),Just configured RAS VPN on ASA5510 and successfully made connection,Now, from RAS VPN (IPSEC) client workstation CLI, can ping all 3560 SVIs,CANNOT PING host devices plugged into switchports.
View 1 Replies
View Related
Dec 27, 2011
In my lab setup i configured Cisco 3560 switch.
-VLAN 20 and VLAN 30 i configured.
-VLAN 20 interface IP : 192.168.20.1/24
-VLAN 30 interface IP : 192.168.30.1/24.
Inter-vlan communication is happening fine. For testing for purpose i configured extended ACLs.i want stop communication from VLAN 30 to VLAN 20 but not vice-versa. If i ping from one of the IP VLAN 20 to one of the ip of VLAN 30, i was gettng Requested time out. And if i ping from one of the IP VLAN 20 to VLAN 30 interface IP, i was able get pinging.From VLAN 30 to VLAN 20, i was getting destination host unreachable from VLAN 30 ip( Its fine as its my requirement)So, solution needed to communicate from VLAN 20 to VLAN 30.
View 1 Replies
View Related
Apr 18, 2012
I have a 3560 switch with the following ports config [code] I would like to use theses ports on a different vlan to connect 4 pc's to them. Can I just remove them from the vlan, remove the trunk switchport and set up on the vlan i want them on with no trunking?
View 5 Replies
View Related
Apr 19, 2012
Probably an easy fix but something's weird in my config. I am setting up a new network, so this is not production, Routed environment, down to the access layer using 3560-x l3 switches.
vlan 10: data
vlan 20: wifi
vlan 30: wifi guests
vlan 40: voip
My objective is to allow all traffic OUTBOUND to certain subnets (10.10.0.0/24, 10.10.100.0/24, 10.10.110.0/24 10.10.120.0/24) and block any other 10.0.0.0/8 networks. By doing it this way, after blocking all other internal traffic, I allow everything else to ensure internet traffic can go out.
Extended IP access list VLAN10_TRAFFIC_FLOW 10 permit ip any 10.10.0.0 0.0.0.255 20 permit ip any 10.10.100.0 0.0.0.255 30 permit ip any 10.10.110.0 0.0.0.255 40 permit ip any 10.10.120.0 0.0.0.255 50 deny ip any 10.0.0.0 0.255.255.255 (5 matches) 60 deny ip any 172.16.0.0 0.0.255.255 70 permit ip any any!interface Vlan10description DATAip address 10.104.10.1 255.255.255.0ip access-group VLAN10_TRAFFIC_FLOW outendThe problem is, from the above info, when I ping 10.10.0.5 from a workstation in VLAN 10, it should match rule 10, but instead if matches rule 50 (as shown by the 5 matches)
View 13 Replies
View Related
