I stuck with a DIR-655 so I don't have to re-program all my custom settings.HOWEVER, I am attempting to load the settings file I saved from my A3 into my new B1 and it doesn't work. It says "The restored configuration file has been uploaded in failure". "Press the button below to continue configuring the router".
View 1 RepliesIs it possible to load the configuration from a saved configuration file from a DIR-625 to a DIR-825? If so, what steps are required?
View 1 Replies View RelatedWe have :DSLT-1 I want to route all VOIP traffic and traffic to one IP address over the T-1, all other traffic I want to route over the DSL. HOWEVER, in the event that the DSL fails, have the DSL traffic failover to the T-1.I have setup the router to do just that (I think) and when I go to a site like "whatismyipaddress.com", it shows my IP as comming from the T-1. With the setup I described that traffic should always route over the DSL.Straight up protocol binding won't work because the traffic I want to route over the T-1 to one specific IP is going to be prot 80 and 443 (web traffic)
View 5 Replies View RelatedI am configuring a load balancer from cisco, a ACE 4710.Load blancing is completely new to me, and i am unexpereinced in this field. It has to be configured for a customer that want to load balance HTTP and RTSP traffic over 4 application servers (Back-end),I searched alot on google for possible solutions, and got RTSP in some way to work, but http wont work says my customer.
[Code] .....
Have two ACE 4710 in HA setup. We would like to setup HTTPS loadbalance(actually just a primary and standby configuration in the serverfarm). Initially this would be for Exchange OWA connections but may expand to more HTTPS connections later. I know there are several ways to do SSL with the ACE( client, server, end-to-end). I am just wanting to know the easiest way to deploy this? Is a certificate always needed on the ACE for each connection? In HA mode would a certificate be needed for both or does it replicate in some way to the other ACE?
View 6 Replies View RelatedI have been experiencing some issue with a portchannel interface.I have two cisco switches 3560 and I have a portchannel between them ( It is composed by two gigabitethernet interfaces generating a portchannel of 2 Gigas ).Unfortunately, I am verifying that one interface traffics about 893MB but the other interface only traffics about 100MB.Is there any cause why is this happening? I thought that maybe both interfaces would traffic about 450MB.Is there some wrong configuration with the load-balance command?. At this moment there is no load-balance, It is only configured the port channel with the default configuration.
View 5 Replies View RelatedCan we terminate 2 WAN link first Lease line and second Broadband internet link on 800 series router . As 800 series router have only 1 wan port and 4 switch port. Also we want to Configure load balancing over the 2 WAN link, is it possible or Basic router for SMB.
View 1 Replies View RelatedI am installing a several new Cisco VM servers. The VM hosts are losing connectivity when we apply the etherchannel config in the core stack. VMware has stated that the etherchannel load balance needs to be src-dst-ip in order for the etherchannel to work.However, my current stack has 2 etherchannels configured to other switches through out the bldg in network closets. The current load balance configuration is src-mac.My question....when I make the change to src-dst-ip, will my network connectivity go down? I saw there was an older article on this that doesnt provide an answer just a work around. Here is the article. [URL].
View 1 Replies View RelatedI have webcams that need port 8081 opened and I did that, everything worked fine until my DIR655 jammed up and power cycling it and the modem 3-4 times DID not make it work: no internet access and it was definitely a DIR655 problem. So, out with the paperclip to do the big reset, causing me to lose my configuration. When "most" of it came back up with my new config (I had screen prints), all was okay EXCEPT the webcams. Addresses and ports were all configured properly, address was fixed too on the client computer rather than use DHCP. I had a DNS relocation service running (DYNDNS) for the WAN side, but that address (My IP) didn't change either. I tried EVERYTHING. Finally, I realized in all my screwing around that I had enabled UPnP in my application, something I hadn't done before, but did this time as a desperation move. UPnP had always been checked off in the router. So.....I REMOVED my port forwarding and virtual server settings (either one worked before), and voila, everything working, Is this a normal occurrence, that if you have UPnP running, that this auto configuration overrides any manual configuration?
View 2 Replies View RelatedI noticed that an specific site cannot load - no response to ping either. I tried that site bypassing the DIR-600 and no problem to connect.
[urls]....
My OS is Windows 7 SP1 32 bit, I also have Vista on the same Laptop (Duel Boot) with D-Link DWA-140 installed.Was installed on the same day and worked with no problem.Installed D-link DWA-140 on my laptop running Windows7 SP1, no problem with the installation.Clicked on the D-Link icon, up came D-link Wireless Connection Manager this was empty, clicked on new and entered my wireless network, clicked on activate, nothing happened.Went to Network and Sharing Center, On the left clicked on change adapter settings, my D-link Connection is showing Disabled, right click, then on Enable, changed to enabling, then enabled, D-link still Disabled.I have the message, Wireless adapter not found, Please insert the adapter now.I went to Device Manager then Network adapters the D-Link adapter is showing and there is No yellow triangle showing, right clicked, This device is working properly.
View 6 Replies View Relatedi can't access to the router interface page at 192.168.0.1 and not from ddns account. but the internet connection working good, and i'm downloading a lot of torrents in background. i just want to check something on the router and can't access to it, until i disconnect from the power adapter and restart it. maybe he's overloaded or something? how to solve this issue?
View 3 Replies View RelatedOne thing I noticed about this router compared to others is the operating temp.It's very "cool" compared to others I've had, especially Linksys. I have a Linksys E2000 that gets very warm, almost worrisomely so.
View 5 Replies View RelatedI have 4 computers using the DIR-615. One of them works just fine (windows 7) the other ones (XP sp3) are very slow, one of which is on the wireless the others are plugged in.
View 3 Replies View RelatedI've been having wireless range issues lately with my dir-615: a lot of holes seemed to have popped up in my house despite nothing changed (house or router location). This is after at least 2-3 years of good coverage and no issues. Went to look at the firmware & found 2.0 installed. Found out online that (I think) firmware is now at 4.11. Tried to download and install but both finding the update and unzipping it proved challenging. Specifically for the latter, unzipping kept yielding more zipped packages, like a russian doll
View 1 Replies View RelatedI'm using DIR 600 for home use. Recently, I noticed that I have trouble connecting to some websites (Twitpic.com, 4shared.com) which I never had any problems before I used the wireless router. It doesn't exactly block the websites but rather it won't load completely (i.e., with Twitpic, I can load the site but not the images; for 4shared I really can't load the page itself).Initially, I had problems updating JDownloader after installation. I tried using our old Edimax wired router, and the JDownloader update worked flawlessly. I also tried loading Twitpic while connected via LAN, and it also worked properly.I'm assuming the problem lies with the wireless router but when I set it up for use I only tinkered with the WPA/WPA2 security for a password-secured wifi connection at home, and nothing more since I can't understand the other features.
View 5 Replies View RelatedI have a D-Link DSL 2640B on the way which I plan on using to replace my 2Wire modem. The 2640B is a combination of a modem/wireless device. Does it dynamically load balances the internet connection? Sometimes while I'm playing online games on my PC and a few others are using the internet for browsing or Youtube, I lag A LOT. Latency shoots up from 10 to 200. QoS goes to ****. And I only need 0.50-1Mbps to keep a steady online play. This was the problem with my 2Wire. So does the 2640B load balance the bandwidth?our max speed is 3.5Mbps according to the ATT Rep.
View 10 Replies View RelatedI have a router Cisco 1901 with 4 links ADSL load balancing, when I activate the links 4, DNS resolution become very slow.
View 3 Replies View RelatedIs GLBP(GATEWAY LOAD BALANCING PROTOCOL) Work as a LINK LOAD BALANCER?
View 5 Replies View RelatedHardware Version: C1
Firmware Version: 3.00
Wired works normally, and wireless is otherwise stable, except when under heavy load. E.g. if I initiate a large TimeMachine backup over wifi to my NAS, it will fail and the wifi will drop requiring a power cycle.I have tried a similar transfer over ethernet (~1.7Tb) and although the transfer speed wasn't great (~10MBs, likely due to NAS drive bottleneck), it completed without a problem.
If I try copying ~150Gb over wifi, however, it barely lasts 30 minutes without dropping out.Once the wifi drops, it still connects, but nothing works (I am unable to even connect to the web interface using the local IP). Other devices connected already via ethernet or 2.5Ghz still function normally, but the 5Ghz just fails, and if I try initiating a new connection to the 2.5Ghz it doesn't work until I power-cycle the router.As far as overheating goes, I'm not sure it is an environmental issue... I have the router standing upright in an open space so there is good airflow around it.
My Dir-615 E1 5.01 works fine, daughters Iphone, laptop connect fine. My Droid Max android phone connects with no problem but does not load web pages or sites. Phone does work great at other wifi spots just not at home with this DLink. My last android phone acted the same way, cannot use wifi at home! Not a password issue cause it does connect and has strong signal.
View 3 Replies View RelatedI am using a DIR 655 router with a DSL 526B modem/router combo. I always get a message saying "Oops! The page you requested is not available.". The page doesnt load (It sometimes does if I keep refreshing again and again). I read somewhere that it might be because I have to bridge my modem/router with my router
View 1 Replies View RelatedI buy this model is QOS, I just read a lot of DIR-655 streamengine article, it's hardware-base QOS router, can operate under heavy p2p application, it's why I am here.The wireless Client is ACER AS1810TZ laptop, the wireless card is Intel wifi link 1000, I have already disable power saving option. AS1810TZ worked fine with my old 802.11G router linksys WRT54GS and Buffalo WRH-HP-54G.The dir 655 seems fine when I just surfing web and download some files with IE, but when I check the statistics, I see a lot of wireless error and tx packet/ rx packet dropped, the percent I calculate is about 0.5%, I am wondering if it's normal phenomenal?When I download several bit torrent files With XUNLEI simultaneously, total 6 files, after 3 minutes, lot of session be created, the router slow down the download and finally crashed, wan be reset and wireless connection lost. router can recover after 1 minutes and try to continue the BT download again, but failed again. [code]
View 14 Replies View RelatedI`m new here I recently purchased the dir-615. I started configuring with cd but i couldn`t get past the step where it should verify if cables are plugged in , so I did it manually. Some pages won`t load , internet speed is slow ( Both wireless and lan speed ) . I am using a PPPOE connection , I even got my ISP to check my settings, and he said it was alright but it reduces my speed by a lot. Usually I download with 1 MB/s with the router on wi-fi I hardly get 50 kb/s and on lan max is 100 kb/s.
View 1 Replies View Relatedwebpage A will take 1 second to load, and webpage B will take 6 seconds to load. After a browser refresh, webpage A might take 5-8 seconds to load, and webpage B will take 1 second to load.
Hardware rev A1 Firmware 1.13NA
Router is about 2 years old.
I tried resetting the router prior to the firmware update, no different. This is happening on both PC's. I tried a direct connect to the modem, and it seemed to work fine, but this doesn't always happen.
i have 2 x T1 terminating on border router cisco 3640 route. (configured using multilink interface). Our IP block is routed on this bundled T1 circuits by At&T. I want more internet bandwidth.
1. Can i connect my DSL (on ethernet interface and using static DSL IP) on the same router and confgure two static routes to internet - one to multilink interface and other to ethernet interface (connected to DSL) ?
2. I have many servers using static NAT to external IPs which are routed on T1 circuits. Will it get into issues when communicating to outside? [for example my exchange server, websites etc?
Whenever I use my router web pages often fail to load. Then after about 30 or seconds or so it will start working again. Even worse,if I go to game online I will have lag like crazy. Even if I am the only one on the router.I'm using a D-Link n300 gigabit router.
View 5 Replies View RelatedWe use Cisco ASA 5520 (in HA configuration) connected to Cisco Switch 3750, ISP connection (25 Mbps) is straight to cisco 3750 switch. Since, Internet traffic is now high, a seecond ISP will be added.Our plan is to do Internet Link Load Balancing. My understanding that AS5520 can not do balancing.What appliance do you think I can use to accomplish the link balance?Also, take in consideration that our current ASA is also our VPN server and there are two DMZ zones.
View 1 Replies View RelatedI have a router Cisco 1901 with 4 links ADSL load balancing, when I activate the links 4, DNS resolution become very slow.
below the router configuration:
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[Code].....
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies View RelatedRegion : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631v1_0.6.0_1.0_up(121214)
ISP : TPG
I've noticed the modem becomes unresponsive under use with torrents and only thing that works is to turn it off & on from power button then works for a few more minutes then crashes again on the latest firmware.
Region : Australia
Model : TD-VG3631
Hardware Version : V1
Firmware Version : TD-VG3631v1_0.6.0_1.0_up(121214)
ISP : TPG
I've noticed the modem becomes unresponsive under use with torrents and only thing that works is to turn it off & on from power button then works for a few more minutes then crashes again on the latest firmware.
We have deploy a Cisco ISR 2921 to connect two ISP for internet access, Link 1 is fix public IP, link 2 is xDSL.And we configure dual link load-balance, the configure just like the famous DOC "[URL]" name:"dual internet links NATing with PBR and IP SLA". Inside network to internet is ok, and traffic was load-balance, Dual link can be redundancy. But there has some issue we don't realize.Most people interesting how the inside traffic load-balance outside, but ignore the traffic from outside issue.
View 2 Replies View Related