Home Network :: AirTies 4450 Static IP Configuration
Feb 25, 2012
I have a router manufactured by AirTies,the model is Air 4450.This has the capability of being an Access Point in a current network, which is how I want to use it. (Introducing it into my current Sky Broadband network with a Sagem F@ST 2504N router).However, I cannot access the configuration page whatsoever.The manual states the default IP address of the router is 192.168.2.254, so I have set my laptop to a static IP of 192.168.2.100 and patched into LAN port #1 on the rear of the Airties 4450, powered on the unit and cannot access the router at all.I have held down the reset button several times to no avail.how I can configure this unit ?
View 2 Replies
ADVERTISEMENT
Jul 2, 2011
I'm connected through a simple non-configurable switch to a 172.20.0.0. 255.255.0.0 network, with a gateway of 172.20.2.2.
When i use DHCP, i am able to connect to the web.
When i change my ip address to a static address (with an available ip address and correct subnet mask and default gateway) i am unable to connect to the web.
View 7 Replies
View Related
Jun 23, 2011
What I'm trying to go for is to make a Static IP so that I can forward my ports in order to play certain games. I have had my ports forwarded at one time with a different ISP (in the same area), however they used cable and the company I'm with now uses DSL. The company "Hawaiian Telcom" has provided me with a Motorola 2210 modem/router. I have had trouble trying to create a static IP with this router so (sorry if this was a stupid move) I decided to buy a linksys router to try to port forward with that. When my ports were forwarded with the previous ISP I was using a linksys router then. The now aged linksys router was replaced due to it getting wet, but that's besides the point
View 11 Replies
View Related
May 28, 2012
For numerous reasons, I want to bind my DHCP clients to static IP addresses, but can't figure out how to do it in DD-WRT.
I've googled, but every link I click times out (for this specific search- my uplink is otherwise fine).
I know I can do it with hardcoded IPs, I'm just curious how static DHCP is done (and yes I am aware that Static is a contradiction in terms of DHCP. I want a given MAC to always get the same IP) and would like to have some info on this.
(call this reserved DHCP if you prefer... )
View 4 Replies
View Related
May 28, 2012
So I have AT&T U-verse and am teaching myself networking and am wanting to mess around in creating my home network and set up static IPs for my devices. I know how to set them up, but I guess AT&T is saying that they have to allocate the static IPs....pretty much they are saying I have to pay them so they can say ok I can use the IP addresses from xxx-xxx-x-10 to and then depnding on how many I want to have depends on how much I pay. This makes no sense to me. Why should I have to pay my ISP for static IP address, from my understanding those are things
View 3 Replies
View Related
Oct 17, 2012
We have a NETGEAR ProSafe™ 802.11g Wireless VPN Firewall FVG318 set up at work with a static IP so we can do a Voice Over IP from our sales office.Everything works fine until I plug in a computer that is connected to our digital printer, then the PC stays on the internet for a while, then crashes the connection.Once I plug in the PC to the network, the rest of the network has issues.
View 4 Replies
View Related
Jun 18, 2012
I am in the process of acquiring a static ip address from my isp time Warner. I only want to pay for a single static, but I have a number of machines I want to put on the internet, a web server and a e-mail-server. Using a cisco router, a Cisco Rv 120w. Can I assign the static ip address my isp gave me to the Rv 120w and then crate a vlan to assign addresses to various computers. Or is this something my ISP does. I get the impression from the tech guy at Time Warner that this is something they do.
View 11 Replies
View Related
Mar 24, 2011
In my router I can set rule that all traffic incoming to router's extAddr:8888, is forwarded to my intAddr:8888. But I also need reverse rule that packets originating from intAddr:8888 are translated to extAddr:8888. Can I do that? What technique can I search on google to find more information, because it is not port forwarding. I would calll it reverse port forwarding or static port address translation, but I do not find anything useful in internet searching these keywords.
View 3 Replies
View Related
Nov 7, 2012
I have 5 Static Ip pool all IPs are working fine. I have deploy a IIS Server on Windows2008 and configure the Static IP on that server. earlier it was working fine . but since last month the IP is not pinging from Out Side but internal IP Pool its working. I have checked the SERver firewall and another Setting is Ok. if i changed the Ip from the server the new IP is also not pinging.
View 1 Replies
View Related
Jan 15, 2013
I've got a server that is connected to the network through one physical ethernet adapter. From my ISP, I got 4 static, public IP adresses, one of which is in use on the Host-Server itself, the remaining three each on a virtualized server. All 4 Servers are running on the same machine.Everything is running smoothly, however, I need to do some Bandwidth Management and Port Mapping, this is why I bought a ZyWall USG20, thinking it would be perfectly capable of doing what I need. is it possible, with a ZyWall USG20, to have all my four IP adresses being forwarded to the one physical machine, and apply some bandwith shaping and port mapping to it?
View 9 Replies
View Related
Nov 21, 2011
I have a problem with my home network/internet - I have a working wireless network that I have used for some time now and it works just fine. the problem is that internet restrictions where I live require me to register each unit to the building network before I can gain access to the internet. My caretaker told me today that normally, I only should register my primary computer and the wireless router to be able to use the internet freely. However when a new laptop appears( I have a guest), I can easily connect it to my own wireless, but it can't use the internet, as if it needed to be registered again. I ran out of registration codes and I really would like to have freedom i connection opportunities. The caretaker said that the system gives every registered unit a "fake" IP, so after giving it to mu router, all other units connected through that router should have unlimited access. Is my network configured in a wrong way? I don't know how to ask this in a more simple way... I just want to be able to connect a friends laptop to the net with just my local password, which isn't happening.
View 3 Replies
View Related
Feb 11, 2011
in my past days i am using bsnl broadband. and also using adsl router for net-connection. i am connecting internet through wifi adsl router. now i am not using bsnl broadband. now i am using beem broadband in hyderabad. that internet connection is directly to my laptop through rj45 cable. but i want to configure adsl router to my beem broadband because i want to connect internet through wifi.it is possible or not? if possible tell me the procedure.
View 2 Replies
View Related
Jan 5, 2012
Here's my situation:I live in a house that has AT&T U-verse. My pc is a couple of rooms away from the U-verse router so I pick up my Internet signal via a Netgear WG111v2 USB wireless adapter. Works great. But I have a couple of "new" Palm Pre handhelds with sync software that requires a wireless connection (won't do USB). Fortunately, I had a Netgear WGR614 v4 54 Mbps Wireless Router in storage. (I used it years ago so it had already been configured but back then it was wired directly to an AT&T router with a patch cable to my roommate's pc and to my pc wirelessly.)
So I just powered it up, plugged a patch cable into my pc's NIC and plugged the other end into the WAN port. Voila! I had connectivity to my Palm Pre's. All was well for about 15 minutes when all of a sudden my pc lost connection (wirelessly) to the U-verse router. And though the Netgear Smart Wizard showed a strong signal from the Netgear WGR614 Wireless Router and the Palm's were picking up a strong signal from it, they couldn't "surf" the Net.
I guess WinXP (being PnP) decided to adjust things causing everything to stop working. (Just a guess.I moved the patch cable from the WAN port to a LAN port. This enabled me to access the Netgear router wizard for the first time since I used it years agohttp://192.168.0.1) I couldn't access it earlier in this "endeavor" when the patch cable was connected to the WAN port. So this seemed encouraging. But no, it didn't work. Nothing was connecting to the Net. And the only way to restore my pc's connection via the Netgear USB wireless adapter to U-verse was to unplug the Netgear wireless router.
View 1 Replies
View Related
Sep 4, 2012
I've been trying to configure a cisco ASA 5505 for my home network but I'm not having much joy with it. I've looked at countless guides, tutorials and followed the ASA setup wizard in ASDM. The Cisco 1841 is running sub-interfaces for my VLAN's.
View 4 Replies
View Related
Mar 12, 2010
configuration of 2 WRT160N's a RT31P2 and a EZXS55W to a home network. The reason behind this is a two story house and running more cat 5 lines for future use.
View 3 Replies
View Related
Feb 24, 2013
I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:
- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface
Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.
- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.
- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.
Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.
Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)
Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).
View 5 Replies
View Related
Aug 19, 2011
Newly acquired DIR-615 E3 with F/W vers. 5.10. Router configured with IPv4 static address for WAN works fine. As soon as I configure the WAN IPv6 with a static IP address also, the configuration for the IPv4 static IP is corrupted. Other combinations of (WAN config) using static for either IPv4 or IPv6 with DHCP or other seem to work. Just appears to have conflict with two WAN static IP configurations.
View 11 Replies
View Related
Sep 3, 2012
I ahve a requirement to configure static crypto for 1800 site and I need to configure on two sepaarte interfacs at spoke site which means I need to configure 1800*2 = 3600 peers at central site. The challenge I have is due to load balancing , the traffic dynamic crypto can not be used since traffic may be initiated from Dc on other link which may get dropped incase not encrypted.
View 5 Replies
View Related
May 11, 2012
I have the cisco 1841, where I am trying to put the static routes on it, it does execute the route commnad but does not show the static route
Below is the out come
lab_router1(config)#ip route 192.168.1.24 255.255.255.248 fas 0/0
lab_router1(config)#ip route 192.168.1.32 255.255.255.248 fas 0/1
lab_router1(config)#exit
[Code].....
View 18 Replies
View Related
Feb 8, 2012
I have configure 887 ADSL router with attached configuration. But users cant access internet properly. (Ex: yahoo and gmail mail cant access)
View 8 Replies
View Related
May 21, 2012
We are replacing our EOL Watchguard X1000 Firewall(s) with Cisco ASA 5510 unit - ASA Version 8.4(3). Following is the static NAT I have build and the corresponding access list.
nat (FW2Inside,FW2Outside) source static BW_XSP1_Private BW_XSP1_Public destinat
ion static BW_XSP1_Private BW_XSP1_Public
access-list FW2Outside_access_in extended permit tcp any object BW_XSP1_Public object-group DM_INLINE_TCP_1
Unable to access the server on the inside interface via the public NAT address. Can you point me in the right direction as to what I might be missing to make this work?
View 1 Replies
View Related
Apr 17, 2011
I'm having some issues configuring NAT statements on my ASA5505 which has recently been upgraded to 8.41.
I have a single dynamic IP on the outside interface of the ASA and would like all internal hosts to NAT/PAT to it. In addition, I would like to have several ports 'forwarded' to internal hosts, one of which is TCP/4343. With the current configuration all hosts are NATing to the external interface properly but the service running on TCP/4343 is not accessible from the outside. See command output below:
"sh run object" output:
object network DrJones host 10.81.220.90object network LAN-10.81.220.0 subnet 10.81.220.0 255.255.255.0
"sh run nat" output:
object network DrJones nat (inside,outside) static interface service tcp 4343 4343object network LAN-10.81.220.0 nat (inside,outside) dynamic interface
"sh run access-list" output:
access-list inside_access_in extended permit ip 10.81.220.0 255.255.255.0 anyaccess-list outside_access_in extended permit icmp any any echo-replyaccess-list outside_access_in extended permit tcp any interface outside eq 4343
View 6 Replies
View Related
Feb 20, 2012
We have 2 sites with 2 internet connections at each site. All are SRP527w routers. 1 is for internet and 1 is for a site to site VPN as,Currently we are using Static Routes on the PC's so they can access each server no matter what site they are at. I have looked at using the Static Routes section on the SRP's but cannot get it to work.
View 2 Replies
View Related
Jul 27, 2012
Purchased the RVS4000 in 11/2012 to work behind a NVG512 in (pass thru mode). I'm running firmware version V2.0.2.7. For whatever reason once or twice a month I lose access to the internet. Sometimes it's AT&T fault but other times my RVS4000 dosen't behave well. I finally took screen shots of every screen I configured in the RVS4000 to make it work in my environment. Last night we lost internet access again. Before unplugging everything I looked in the RVS4000 and found that my WAN setup had reverted back to a default Automatic Configuration - DHCP instead of the Static IP that I had previously saved.
It seems that my RVS4000 is losing just that WAN setting (port forwarding and Static IP Mapping data and VPN client data is still intact.
View 6 Replies
View Related
Oct 20, 2011
Here's the layout: Cable modem in the basement. Several devices in which I'd prefer a wired connection in the basement. Upstairs on the 1st and 2nd floor of the house are many devices in which wifi is fine or preferred.Here's the problem: As you might guess, wifi is weak upstairs and certainly on the patio and 2nd floor. I have an access point upstairs that I've experimented with but it is flaky.
View 1 Replies
View Related
Nov 10, 2011
How to install a wireless network in home environment?
View 6 Replies
View Related
Jan 14, 2012
I am a new student in networking, taking the CCNA courses, and now want to rewire my home. I currently have a cable modem and E2500 setup running my network. I want to get the modem and router out of my computer room and in the basement where the cable enters the house. I want to do this to clean up the computer room wiring a bit and to run line drops to different rooms in the house where the internet will be utilized.Currently there are two PC's, a laptop, a tablet, sometimes a phone, and an XBOX using the internet. I want to get my printer back up and running on the network but thats another story. Only one PC is currently hardwired. I would like to run two cables into the room with the PC and XBOX that are currently using wireless, at least two into the computer room for the PC and network printer, and one or two into the living room for the blue ray player and possibly an internet tv.
View 1 Replies
View Related
Sep 10, 2011
I have a D-Link DGL-4500 router and my landlord recently ungraded our internet connection. However, now I get this error message when I try to hook it up to the ethernet hub,"The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
View 3 Replies
View Related
Jul 30, 2012
I'm experimenting a strage issue with some AP1142 that prefer getting new IP from DHCP server rather than using the static ip already configured.
I've got more than a hundred of 1142 APs already conected to a 5508, all with static IP, all working fine for about a year.
As i installed 30 more AP, i enabled a dhcp scope on the controller to give IP to the new APs and when the new aps got registered i changed the configuration to static IP.
The problem comes when some of the older AP than have already static ip are gettig ip from dhcp scope.
If i look at my WCS, it reports that this APS are getting DHCP IP because they cannot reach the controller with their static ip. As this is impossible, because the static ip and the dhcp enable scope are in the same subnet in a layer 2 configuration and with the same gateway. (e.g: old AP 10.10.2.10/16; new AP(dhcp 10.10.3.10-50) 10.10.3.15/16; gw 10.10.254.1)
The problem comes when i disable the dhcp scope, all the older aps that got dchp ip from the wlc scope instead of using their staic configured ip are deregistered. If i reset every ap manually, from the swithc disabling PoE, they start to use the static ip and everything comes fine.
This is happening with about ten of fifteen APs from the 100 installed, that is the strange thing because this seem to be very random as the failing APs are installed in different building and connected to different switches.
As now i have disabled dhcp scope and all APs (old and new) have static ip everything is ok, but i will have to add some more APs shortly and every time i enable the dhcp scope on the wlc
View 8 Replies
View Related
Dec 4, 2011
How do I create static smartport macro on Catalyst 2960 & 3750 equivalent to below static smartport macro:
macro name NOT_USED
description UNUSED_PORT
switchport
switchport mode access
switchport access vlan 100
shut
@
I am able to create above smartport macro on Catalyst 3760 & 6500, but not on 2960 & 3750 (see below):switch(config)#macro ? auto Macro autoexecution settings global Enter global macro configuration
View 12 Replies
View Related
Dec 20, 2012
I have setup a webserver on my home PC and I have forwarded port 80 on my router to the IP adress of the PC that is running the web server. The web server is working great; I can get to my web pages from outside of my home by going to http://MyIpAddress/Anyway, the problem is with the Windows Media Player plugin I'm using. I want to embed 6GB MPEG-2 videos into my web pages. I have some videos on my PC and I want to be able to watch them remotely by connecting into my web page. It works fine when I'm at home; other PCs can connect and play the videos no problem. The problem is when I'm at work. When I'm at work, I go to my web page (via my IP address in a web browser) and the Media Player plugin says "Connecting" for a minute, then it says Ready, but the video will not play. I tried using a smaller, AVI file (680 MB) instead to see if the problem was streaming such a large file, but the video still would not play.Do I need to foward more ports on my router so that Windows Media Player can connect back and get the information it needs?
View 4 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Sep 20, 2011
I'm currently in the process of buying the new property, which is in the build process and would like to put some cables across 3 floors, which would be connected to the router downstairs.
View 3 Replies
View Related
