Cisco WAN :: WS-X6704-10GE Along With SUP-2T Which Will Be Configured In VSS
Feb 9, 2013
I would like to know if we can use the following card i.e. WS-X6704-10GE along with SUP-2T which will be configured in VSS.
This line is supported with SUP-2T, however not sure if the sup 2t will be configured in VSS. If any supporting document can be provided for the same , that would be great.
If this is supported than whether i would be getting line rate/non blocking capacity with WS-X6704-10GE. Since SUP-2T provides 80 Gbps bandwidth per slot.
View 5 Replies
ADVERTISEMENT
Dec 7, 2011
We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
View 2 Replies
View Related
Jul 21, 2011
I am testing rogue on wire using 5508 WLC and , I have a dedicated AP configured as rogue detector and configured the switch port where the Rogue detector is connected as trunk. I have plugged in an autonomous AP with open authentication to the same switch so that it can act as a rogue. On the WLC, I can see that Autonomous AP as rogue on Wire. But along with that I am seeing another AP as rogue on wire, even though i have plugged in only one Autonomous AP to the switch.
View 3 Replies
View Related
Sep 19, 2012
One of our Cisco 6500's fitted with a WS-X6704-10GE line card is showing a large number of Rcv-Err's on port 3. The port is disabled and no optic is even plugged in.Upon clearing counters, after every refresh the counters increment by 131070 -- so 131070 > 262140 > 393210 and so on. Seems a little strange that the buffer is full when nothing is connected.
View 3 Replies
View Related
Jan 1, 2012
Clarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
View 1 Replies
View Related
Mar 7, 2012
I just added a X6704 card to our 6513 switch, and it is not working correctly. We are running 12.2(33)SXI5. [code]
View 5 Replies
View Related
Jan 6, 2013
The difference between the link terms 10G & 10GE?
View 1 Replies
View Related
Oct 9, 2012
My customer has upgrade his 4506 from 6L-E to 7L-E 10GE.Ever since then if he run the command show dot1x interface gigabitEthernet x/x details some information are not been displayed (below are missing information)Is this intensional or do I need to kick this to TAC?
View 1 Replies
View Related
Nov 17, 2011
How to confirm if a 10Ge interface can be set down to 1Ge if required ?
View 4 Replies
View Related
Dec 3, 2011
I was looking at the data sheet for the VS-S2T-10G and there was no compatibility mentioned with the WS-X6708-10GE module.Is this module compatible with this new supervisor?
View 2 Replies
View Related
Jun 5, 2013
We had to transport one of our 4948 10 GE to another Data Centre and when we got it there and tried to power up its System Status LED was red and we cannot even get console to the device.
We can try to see if the switch is completely dead and needs replacing or is there something we can do to get it back up and running again?
View 1 Replies
View Related
Nov 18, 2012
I am in front of a choice what to select to deploy 10Ge in my datacenter to get four 6504e and two 3750x units connected to each other.All devices are located in 3-7 meters away from each other.The choice is whether to go for a multimode fiber and 10GBASE-SR X2 Modules OR cat7 UTP and 10GBASE-T X2 pluggable transceiver.Money wise it doesn't matter.Fiber looks less attractive since it's fragile and a bit harder to put in underfloor area.Cat7 is more attractive but there are 2 points:
1) I couldn't find ANY single photo of a 10GBASE-T (a module with a single RJ45 port). How does it look? Does it come with a cable or...??
2) How stable is it to run 10Ge over UTP?
View 1 Replies
View Related
Oct 24, 2011
I have a pair of 5585X-SSP20's which is working in active/standby multi context mode. The code is 8.2(5) and i have the ASA5585-SSP-20 VPN Premium license.
I am planning to utilize the 10G interfaces. Is it possible to have a single license for 10GE I/O and share it between the two chassis in ver8.2(5)
View 2 Replies
View Related
Jan 28, 2013
I have a two Cisco 4510R each with two sup V-10GE redundant. The code on these sup modules are 12.2(31r)SG3. I need some assistance in getting this setup worked out. I have all four of the 10GE populated with appropriate optics. I setup a link from one 4510R to the other using these interfaces. From the documentation I found I had to use Tengi1/1 and Tengi2/2 as the redundant pair. I plugged the up link into these ports. The Tengi1/1 (active supervisor) links up and works fine. But when I look at the ports port Tengi2/2 it isn't showing link or active. Now port 2/1 (nothing plugged into it) is showing as active.
Now is the redundancy supposed to be 1/1 and 2/1? If so, the switch is in production, when I move the connection over from 2/2 to 2/1 will it cause a outage? The reason for this is I now have a system with a 10G port and would like to utilize one of the other 10G ports. Is that possible? Or does it have to be a lag/redundant up link to work (say to another switch)?
View 2 Replies
View Related
May 6, 2013
We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
View 6 Replies
View Related
Apr 25, 2013
i was checking the datasheet of 500X series and got confused regarding the 10GE uplinks. how many 10GE ports can be used for uplink and which transceiver should be used for 10GE copper uplink? for example, SG500x-24 switch has 24GE ports and 4x10GE uplinks. can i use the 4x10GE ports for uplinks or only 2 ports are for uplink and the rest for stacking?
View 6 Replies
View Related
Jun 17, 2012
What does RP drops entail? We are experiencing 0.23 % drops on an vlan int on one of our 6500. This interface is an L3 to a server-subnet. Doing a sh int vlan 238 switching shows 30935411 RP (Route Processing) drops.It was a bit unclear to me in the thread "Input queue drops on 6500 vlan interface" if RP drops was through the router, or to the router(mgmnt)?I can do a netdr to see what traffic goes to it. It should not generate CPU load, but I think I will wait until after hours before I try that command.
- do NETDR:
-- debug netdr cap rx vlan 238
-- show netdr cap
View 5 Replies
View Related
Jan 22, 2013
We have two 3750 stackable switches in core layer.
1. We are planning to stack two 3750 for greater bandwidth to use
2. We could configure 10GE link (by Network module) between these two switches
which solution provides increased bandwidth and redundancy?
View 5 Replies
View Related
Feb 7, 2013
I am trying to configure a 6509 as the passive receiver from a Dell Force10 10Ge switch with 2 sfp to 2 gig ports on our 6509 switch, I see LACP is up on both sides but cannot pass traffic, I have only 2 vlans that will carry across the aggregate link from our vmware boxes, this is just a temp until I get a 10ge in our 6509 chassis.
View 2 Replies
View Related
Apr 18, 2013
i have a Cisco 7609 with ws-6704-10ge, trying to test a cable that is connected to the 10Gig interface , i connected the other end to a 1Gig GBIC interface on WS-X6516-GBIC, now the speed does not match but how to force the 10Gig interface speed to 1Gig, will that ever work? both has LX optics and the cable is SM
View 2 Replies
View Related
Jun 4, 2012
I am getting conflicting info about this, and need to get confirmations.Is the older 6513 (non E) model compatible with WS-X6407-10GE blade?The switch we're getting this for have WS-SUP720-3B, 6000W power supply, and WS-C6K-13SLT-FAN2.From what I read they are compatible if entered in slot 9-13, but I also heard that 10GE modules are not compatible with the non E chassis.
View 1 Replies
View Related
Feb 27, 2013
I am looking for 10 GE copper 24 ports switch. After any time I come N2K-C2232TM-10GE. However, this switch is fabric extender and it is used with Nexus 5K series switches.
My question is Can I use this Nexus 2K standalone as other L2 switches?
View 4 Replies
View Related
Sep 23, 2012
We have CORE switch model : Cisco WS-C4510R-E with dual SUP 5 - 2 10GE. [code] Now We want to upgrade this IOS to the upgraded version.
View 3 Replies
View Related
Sep 8, 2011
I will be adding two WS-X6716-10GE cards in a CAT6509 soon, and will create 4 port channels with 3 ports each in the new cards, but I do have a few questions:
1 - I will be adding cards in slots 3 and 8, can I mix and bundle ports from both modules into a single etherchannel, I mean, like two ports in slot 3 and 1 port in slot 8 to create a PortChannel ?! Or can I only bundle ports in the same card/port-group in a Etherchannel using this WS-X6716-10GE card?
2 - Do I need to issue the hw-module slot x oversubscription port-group y command in order to be able to bundle ports in the Etherchannel I need to create ?! I will be using 4 Etherchannels (LACP) with 3 ports each, running in trunk mode. So I guess, I will be using something like:
int tengig 3/1
switchport mode trunk
switchport trunk encapsulation dot1q
logging event link-status
[Code] ....
View 4 Replies
View Related
Dec 4, 2011
Is it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies
View Related
Jul 29, 2012
I have been trying to reset my Cisco 4507 R-E with sup 10GE engines, and I am not having any luck. I have followed the following document:
[URL]
I have tried "wr erase" and "erase startup-config." I cannot delete the vlan.dat file either. I am using the command "erase cat4000_flash:vlan.dat" and its not working either. I have done these commands several times with no success. When asked if I want to save the config changes, I am answering with a "no" I have not tried to depress the small "reset" button on the front of the sup engines as I read that this just restarts the switch.
View 2 Replies
View Related
Jun 5, 2012
I tried to configure netflow without success.
Setup is the following.
Cisco Catalyst 6509 with Sup720-10GE IOS 12.2(33)SHX7. There are around 30 L3 vlans configured on the switch. I'm only interested for the traffic on one L3 vlan which is the connection to wan cloud.
I wanna see only the traffic that goes to and come from the wan. On other Catalyst where I have routed interfaces i successfully configured netflow. I read a lot in the forums and documentations but i didn't find the right one.
View 1 Replies
View Related
Aug 3, 2011
I am trying to setup the management vrf on the 4948 10GE so that my TACACS requests will use that vrf for out-of-band purposes. The vrf is working properly because I can ping the TACACS server using the vrf but the logins do not work. I see this error in the tacacs debug:
TPLUS(00000016)/0: Connect Error No route to host
Looking at the release notes, it states that my version (12.2.54 SG1) does support vrf aware tacacs but the documentation seems to be a bit off because i do not get a server private command option as stated in the configuration doc after configuring a tacacs server group:
[URL]
Here is my config:
ip vrf mgmtVrf
rd X:X
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address x.x.x.x
[code]....
View 7 Replies
View Related
Aug 12, 2011
After inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies
View Related
Jan 17, 2012
When i swapped a Sup v 10 ge for a Sup6 E Tonight in order to take advantage of the netflow capabilites of the Sup V - It came up with module unsupported for the following cards - WS-X4648-RJ45V-E Will these only work with the Sup6 E or what
View 2 Replies
View Related
Oct 25, 2011
ive updated my catalyst 4948-10GE to version 15.0(2)SG1.Now it is not possible to login by ssh or telnet on this switch. the access is established over the mgmt-Interface and vrf.i get a ping reply but login is no more possible now.is there an new feature in this version for vrf or remotelogin that has to be configured? if neccessary i can paste the running-config here.
View 3 Replies
View Related
Sep 11, 2011
just want to confirm if I could use the 2x 10GE uplink ports of a cisco 2960 to connect to my Server directly?
View 17 Replies
View Related
Dec 25, 2012
Is Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies
View Related
