One of our Cisco 6500's fitted with a WS-X6704-10GE line card is showing a large number of Rcv-Err's on port 3. The port is disabled and no optic is even plugged in.Upon clearing counters, after every refresh the counters increment by 131070 -- so 131070 > 262140 > 393210 and so on. Seems a little strange that the buffer is full when nothing is connected.
View 3 RepliesClarifying whats the correct # of port asic in WS-X6704-LC?According to the following link (Catalyst 6500 Architectural white paper): [URL]
"In the WS-X6704-10GE line card, there are two port ASICs each supporting 2 x 10 Gigabit Ethernet ports"
While in the document: Understanding Quality of Service on the Catalyst 6500 Switch: [URL]
Table 10.
WS-X6704
Number of 10 GE Ports 4
- QoS on 10-Gigabit Ethernet Line Cards (WS-X6704-10GE)
So whats correct? 4 port asic or 2 port asic?
# Port ASIC’s on the linecard 4
# Physical Ports per Port ASIC 1
We have two 6509 switches with one WS-X6704-10GE module in each of them. There is an optical cable between the two switches plugged in WS-X6704-10GE module on both sides. When you shut down the port on one side the other port still stays as up and you need phisycally to unplug the cable to have it down. The same behaviour is seen no matter on which of the two switches you shut down the port, the opposite one always stays as up and only removal of the cable makes it go down.
The ports are configured quite simply:
interface TenGigabitEthernet1/1
switchport
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1-10
no ip address
udld port
The IOS version is 12.2(18)SXF8
I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies View RelatedWe are having troubles getting a 10Gig interface to come up with a carrier... it shows down down.We are using X2-10GB-LR on a 6500 and SM fiber, distance to carrier hand off is about 90 feet.
According to: [URL]
The receiver power on a X2-10GB-LRis
Max
0.5
Min
-14.4
Our carrier is sending at +5db. Currently the interface is down.
My question is; would the interface even come up if it is receiving a powerful signal?
Here is DOM output for our interface.
show interfaces transceiver detail
Optical High Alarm High Warn Low Warn Low Alarm
Transmit Power Threshold Threshold Threshold Threshold
Port (dBm) (dBm) (dBm) (dBm) (dBm)
[Code]....
I am unable to connect to the internet on my desktop computer. The error message I receive is" Download failed(12007) The sever name or address could not be resolved" I am running windows 7. Hooked up to att uverse. My laptop is working as you can see by sending this message. I have been trying to fix this problem for the last 2 days to no avail. I uninstalled norton hoping it was a firewall problem. On the local area connection it shows IPV4 connedtivety: No Network access.
View 2 Replies View RelatedI recieve 0X800CCC0F error message when trying to download emails with attachments. My ISP is BT. BT say they cant fix it on my computer but many people are having this problem. They say their technicians are trying to fix it presumbably on the servers.
View 1 Replies View RelatedI'm starting to see an error creep up that I havn't seen since 2003/2004 on my brand new 5508 controllers. I'm recieving the following from my WCS: Receive Multicast Queue is full on Controller and then on the controller itself RX Multicast Queue Full. I understand this used to be due to a large influx of ARP requests or CDP packets on older controllers but, this was supposed to be fixed in an update many years ago.
Has seen this on their 5508's. These were advertised as having the horsepower to handle our user loads which arn't really that high at 300 users at any given time max.
I have an old Buffalo router which im trying to connect to a virgin media modemProblem is the router doesn't have a direct Ethernet port for internet, only ADSL.What I thought I could do was connect using one of the LAN ports and make my router think it was receiving internet through a network? Is this possible and how can I do it?
View 6 Replies View Relatedis there an adapter ( wifi reciver ) that plug into RJ45 port so RJ45 can receive wifi signal ?
View 1 Replies View RelatedI have a problem with my WAN ports. I can´t obtain a ip adress from my ISP. I´ve tried factory reset. Upgrade to lateset firmware. Clone MAC adress from my PC. Nothing is working.
But when I plug the WAN port into my Old router it receives an adress directly. When I plug the ISP connection directly into my pc or the old router it´s working as well.
I am using the latest firmware: RV0XX-v4.1.0.02-tm.bin
And My ISP has an interface with an ADSL modem SmartAX with DHCP.
On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp
I would like to know if we can use the following card i.e. WS-X6704-10GE along with SUP-2T which will be configured in VSS.
This line is supported with SUP-2T, however not sure if the sup 2t will be configured in VSS. If any supporting document can be provided for the same , that would be great.
If this is supported than whether i would be getting line rate/non blocking capacity with WS-X6704-10GE. Since SUP-2T provides 80 Gbps bandwidth per slot.
usually when I get a card that throws this error I assume it is dead however I just want to verify that I am not missing something[CODE]
View 2 Replies View RelatedWe have NAM-2 installed in 6500 chasis. Some times in GUI It does not analyse the traffic and shows the error msg"error communicating with RMon daemon". But at the same time we can login to NAM through CLI,
The issue resolves by reseting the module by hw-module switch "" module "" reset but not always and happens not very often,
Device details:
NAM application image version: 4.0(1a)
Maintenance image version: 2.1(5)
NAM Daughter Card Micro code version: 1.34.1.28 (NAM)
[Code].....
I have 6500 VSS Core Switch configured as NTP Server .I have installed ACS 5.2 vmware and sucessfuly integrated with the AD . I have noticed in some case, i lose connectivity between ACS and AD and when i say test connection , it shows clock skew error . Reboot of ACS sometimes solves the issue, else it comes up automatically after some hours . In core switch , i have configured time as PST +4 and in ACS it is configured as PST +4 , which automatically goes to GST.
View 15 Replies View Relatedi have this message "DHCP Timeout"on few cisco IP Phones . try to assign IP manually and it's working fine.. seems DHCP not giving IP's to those.. 6500 have configured as DHCP pool.
View 3 Replies View Relatedmy MSFC2 sent this strange log message. %DATACORRUPTION-SP-1-DATAINCONSISTENCY: copy error, The error message decoder tool says: "NOT FOUND". The level is "alert".
View 8 Replies View RelatedCisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer inspection of the Switch Sys log, I observed the following Sys log error messages: [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.
View 2 Replies View RelatedSince yesterday, i see
Nov 16 13:23:21.355: %SYSTEM_CONTROLLER-3-MORE_COR_ERR: 255 correctable DRAM memory errors in previous hour
Nov 16 13:23:21.355: %SYSTEM_CONTROLLER-3-COR_MEM_ERR: Correctable DRAM memory error. Count 623, log 8053C830
Nov 16 14:23:21.340: %SYSTEM_CONTROLLER-3-MORE_COR_ERR: 255 correctable DRAM memory errors in previous hour
Nov 16 14:23:21.340: %SYSTEM_CONTROLLER-3-COR_MEM_ERR: Correctable DRAM memory error. Count 879, log 8053C810
error on switch console every hour.
ios version : Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2)
I was trying to configure copp on one of 6500 sup-2T. Is it ok to add customized policies to the default copp "policy-default-autocopp".When I created my own customized policy using policy-map, I get following error
control-plane service-policy input policy-custom
error: failed to install policy map policy-custom
Our client has MPLS connected all sites. Each site has a router connected to MPLS via serial interface, and connected to the switch (6500) via ethernet interface. There is QoS applied on the serial interface for outbound.
It appears there are lots of inbound traffic coming to the site, and the client applied QoS on outbound.What I learned that after the packet are marked by the CPE, the ingree Provider Edge Router (PER)uses these marking to map flows to various Label Switched Paths (LSPs) providing differentiated treatment accross the network. Then at egree, the PER applies queuing policying based on the CPEs orginal DSCP markings to properly allocate bandwidth on the egrees link during congestion. My guess we really don't need to have inbound policy applied in the serial interface on the router, am I correct?
The serial interface has 1.5 MB, and the goal is we want to have 1 MB for cirtical apps, and 0.5 MB for download/upload internet access. If we apply this policy on the switch, A) should I apply it on the VLAN interface or the port connected to the router?
I just added a X6704 card to our 6513 switch, and it is not working correctly. We are running 12.2(33)SXI5. [code]
View 5 Replies View RelatedI've been using a WRT120N on a local area connection.The WRT120N acts as a gateway and also to connect to the PPOE connection, via a bridged adsl modem.I've noticed that the LAN port 1 was flashing although the network cable was disconnected from the physical port. I've restarted a few times but to no avail as well. Ever since that, I've noticed that connection through cable are unstable and hard.Now, I'm not able to reset or upgrade the router's firmware.Is there any other way to be done so that I can get this router working as normal again.
View 6 Replies View RelatedI have 2x v10000 Websense Security Gateways that are connected to 2x 6500 SUP720. When I turn on cluster management function between Websense appliance, they speak to each other only if they are connected in the same 6500. When they are connected one in every 6500 cluster management does not work. They are connected on the same physical vlan. Do I need multicast to be configured in the 6500 switches?
View 5 Replies View RelatedI have configured remote access VPN with radius authentication in my firewall ( ASA 5510). When tried to connect the VPN with Cisco vpn client, the following error is showing,
"Error: Secure VPN connection terminated by Peer. Reason 433 (Reason not specified by peer)".
I have a HP CP2025N laser printer that has been happily working on my Apple network. Now all of a sudden I keep getting a "printer not connected" error. I reset the network to no avail. I am running Lion, the printer is connected via an ethernet cable on a Apple Express routter that extends an apple extreme. Again this configuration has been running for two years now.
View 2 Replies View RelatedAfter making some physical changes to my home network (which had been running for sometime without incident) my desktop machine stopped (home built MSI X58 Platinum MB) talking to the network. I get "media not connected" even though I am connected, and the connection works for any other computer I attach. I get indication of proper physical connection at both ends (router and computer ethernet port), however I get no connection and the default 169 .... IP address. It does not matter if I create a fixed IP address in the router and set the ip address of the port to correspond. I have tried all the ip resets, stack resets, remove and reinstall the network ports, etc., to no avail. Connecting directly to the cable modem did not work. I even installed a new buss ethernet card with its own drivers and I get the same 'media not connected'.
View 3 Replies View RelatedI have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies View RelatedSo basically my laptop shows its connected to my wireless but when i try to browse it wont let me?
View 3 Replies View RelatedI have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..
View 1 Replies View RelatedWe have one cisco core switch 6500 series which was configured portchannel on several gig interfaces. This port is used as a trunk to enable communication between VLANs. The VLANs is where several high-end servers/hosts reside.After we disable / unbind the portchannel, the port turns amber. The following is what we did on the interface
1-no switchport command
2- make the port as access mode #switchport mode access
3- shut and no shut
4- clear arp
5- clear mac
what else can we do on that particular interface. It is just on that particular interface, the rest are ok.
i have several cisco 6500 switches, and user switched connected to them.in my example i have a global service vlan, where some access ports are directly connected on the 6500, and this vlan is also allowed on the trunks to the access switch.
now i am connected with ma laptop on a access switch, where my port is in the same vlan. when i do a show mac address-table on my access port, i can see my own mac-address, nothing else.when i start wireshark to see the traffic, all i should see is traffic from or to my MAC, or broadcasts/multicasts.
But i can see other unicast traffic with different source/destination mac than mine.It seem slike these packets get broadcasted over the whole VLAN, but its no broadcast MAC nor IP.