Cisco WAN :: Redundancy With Existing Sup Engine WS-x4516
Mar 12, 2013I have supervisor engine ws-x4516 with two line card WS-X4424 - GB - RJ45 - 1No ,WS-X4548 - GB - RJ45 - 1No. Now i want switch and hardware redundancy.
View 3 RepliesI have supervisor engine ws-x4516 with two line card WS-X4424 - GB - RJ45 - 1No ,WS-X4548 - GB - RJ45 - 1No. Now i want switch and hardware redundancy.
View 3 RepliesI've 4500 Core Switch with 4507R chassis, Sup V-10GE(WS-X4516-10GE) along with 2 WS-X4306-GB line Cards, but now I require a line card for 14 more fiber up links and I cannot go with 3 of 4306 as there are only 2 slots left. I've checked and found that E series line cards does not work with Sup V Engine.
As per the link below, I found that "WS-X4448-GB-SFP" is compatible..
[ URL]
How to configure Supervisor Engine Redundancy between two different cisco 4507R and 4506E.
View 5 Replies View RelatedIs it possible that catalyst 4500 Supervisor Engine V-10GE WS-X4516-10GE works with WS-X4612-SFP-E?I know suprtvisor engine V-10GE is not support E-serious linecard, but when I use the configuration tool, I can choose these two products together. Is it a bug?I need novell IPX in this case, I find supervisor 6E & 7E are already not support, so I have no choice to choose V-10GE.
View 1 Replies View RelatedI was trying to upload image to sup x4516 V10G from Rommon using the management port but did not succeed. The steps which I did as mentioned below: [code]I got the tftp request on the tftp server but from the switch was showing access violation
View 0 Replies View RelatedI am able to ping the ACS ENGINE 4.2 from any PC or device. But I am not able to ping any device from the box while logged in via SSH. while I can do so while logged in via console. Is this some kind of bug or is there any patch which after installing will allow me to ping devices from ACS SSH sessions.
View 3 Replies View RelatedIn my existing production router 7609 of my company, sup-engine already fixed in slot 5 with SRC2 12.2(33) IOS and I need to insert another sup engine in slot 6 with SRE7 IOS code image and after this, again sup engine in slot 5 must be with SRE7 IOS image...(also I have extra sup engines with SRE 7 code image ready with me) Query:i am going to offload router before proceed for this activity?i will insert new sup engine in slot 6 with SRE 7 ios image and now i need to re-install spare sup engine with SRE 7 code readily available with me by removing existing sup engine from slot 5 (Active) so what will be the proceedure to insert new sup engine with SRE 7 code in slot 5 and slot 6 with minimum downtime of router?
existing setup sup engine in slot 5 with SRC2 12.3 (old hardware) slot 6 is EMPTY
final result should be like this: sup engine in slot 6 with SRE 7 (new hardware)
sup engine in slot 5 with SRE 7 (new hardware)
In my test lab , I have a CISCO 1841 with a AIM-VPN/BPII-PLUS board , everything was working fine , until I would like to see the difference with and without the accelerator.Sins the moment that the IOS told me that he will change to SW accelerator instead of HW accelerator , I can not make it work anymore.I have a copy of the full working configuration before I did this , I have put it back on my router but still NO VPN. [code]
View 2 Replies View Relatedcan I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View RelatedI have a cisco 7609 with sup engine 720, I want to implement VPLS for that I purchased a 7600-ES+20G3C with the adv license 76-ES+ADVIP-LIC in a separate pak?how to activate the license on the 7609.
View 3 Replies View RelatedI have an inventory added to Ciscoworks and am getting alerts on interfaces that I want to exclude but for the life of me I can't figure out how to exclude interfaces. Any tips on how to exclude interfaces from the fault engine in 4.1.
View 3 Replies View RelatedMy existing 4006 chassis is using Supervisor III (WS-X4014). I have another 4506 chassis using Supervisor IV (WS-X4515) and a Net flow Services Card (WS-F4531) build on top of it.
I need Net flow Services Card in 4006, so can I just replace the Supervisor IV (WS-X4515) used in Cisco 4006? Is it compatible with 4006?
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies View Relatedi have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies View RelatedRemoving and Installing a Supervisor Engine on a cisco router 7690 and more important IOS upgrade of this module.
I need some kind of manual, but I would prefer a short procedure to do this change. A brief of the steps to do that. Also i don't if i have to upgrade the new module after install it.
PD.
IP7VAL02#sh modMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1034Z32J 2 48 CEF720 48 port 10/100
[Code]....
I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View Relatedto the above question. I see the specs for the WS-SUP720-3B and 3BXL but not the WS-SUP720-BASE with the MSFC3 and PFC3A daughter cards.The 3B can handle 256,000 routes using IPv4 and the 3BXL can do 1,000,000.
View 4 Replies View RelatedI have recetly upgraded our core switches (6509E) to SUP 2T from 32. Each core has 2 SUP's (hot/standby). out of 4 SUP engines, one is defective. i had received the new SUP from cisco. Currently my core swicth 2 is running with single SUP. Can i directly insert the new SUP engine in slot 6 (free)? will it automatically load the existing IOS from active SUP? what will happen if the new SUP has a different IOS other than the active SUP? Also is there a way to find out the IOS version without inserting in the chasy?
View 2 Replies View RelatedIs the ISE going to support the 2500 series Wireless LAN Controller WLC? If yes in what release and appriximately when is that due to be released?
View 1 Replies View Relatedwe have installed the MSE 3350 with the lates Context Aware Sup Service from AeroscoutBut the Service still terminated because of unexpected null node message (see below)
View 7 Replies View Relatedi cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedI have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies View RelatedI would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before
View 5 Replies View RelatedI've connected my c3560G which I use as Core-switch in my company to Prime Infrastructure 1.3.And sometimes I see a CPU overload over 50% only by SNMP ENGINE process. Total CPU load at this time - up to 100% Possibly, It's happened after IOS update from 12.2(25r)SEE4 to 15.0(2)SE2 C3560-IPSERVICESK9-M.
I've exclude some OIDs from snmp view, but problem is still exists:
PRIMEview internet - excluded nonvolatile active
PRIMEview mib-2 - excluded nonvolatile active
PRIMEview system - included nonvolatile active
PRIMEview interfaces - included nonvolatile active
PRIMEview at - excluded nonvolatile active
[code]....
Based on the stace trace, how do I determine what object is being polled??? (what is causing the high cpu for SNMP ENGINE)
From the “show stack 295” output (SNMP ENGINE)
router>show stack 295
Process 295: SNMP ENGINE
Stack segment 0x68226DC0 - 0x68229CA0
FP: 0x68229BD0, RA: 0x62A0D95C
FP: 0x68229BF8, RA: 0x628276A8
FP: 0x68229C68, RA: 0x629FBE08
FP: 0x68229C80, RA: 0x629FBDEC
We have a scenario with 2 chassis, both with 2 supervisor Engine 2T, we try to make a configuration of VSS with the chassis and would link to know if is possible have 2 supervisor on chassis one and 2 supervisors on chassis 2 with VSS?
Router#sho switch virtual redundancy
My Switch Id = 1
Peer Switch Id = 2
Last switchover reason = active unit removed
Configured Redundancy Mode = sso
Operating Redundancy Mode = sso
[code]....
would like to use the second supervisors for obteind the local redundancy en chassis 1 and 2, this is possible?
the actually version on four supervisors is: s2t54-ipservicesk9-mz.SPA.150-1.SY3.bin
I have a 510a Cache engine and the IDE hard drive failed. I installed a new blank hard drive, but I can't get it to boot off of the new hard drive. Currently, I moved the original to Disk 1. I switched the boot up disk to disk 1. I was then able to setup the new hard drive (in disk 0). Everything is functioning, but I don't want to keep the dead hard drive in there. How do I setup a boot sector on the new hard drive?
View 3 Replies View RelatedOur ACS appliance (Cisco 1113) has died and it is not cost effective to get it replaced as it will only be used until the end of this year.Is it possible to get the tacacs software to install on a Windows server? How do I go about sourcing the software as the original documentation is no longer available? Will the fact that I have a defunct appliance be sufficient proof to get a copy of the software? We are currently running v4.1
View 1 Replies View RelatedWe recently perchaced 4503 switch with Sub Engine 7L. It has universal IOS. We are unable to run EIGRP and HSRP protocol and the switch came with temporal license.how to proceed further to get EIGRP and HSRP enabled on the 4503 switch.
View 8 Replies View RelatedI was looking to 6500 series switches. I saw DFC4 module (WS-F6K-DFC4-A, WS-F6K-DFC4-AXL) and (WS-F6K-DFC4-E, WS-F6K-DFC4-EXL). Data sheet for supervisor engine 2T wrote that for maximum performance you should DFC4. I'm a bit confused. I didn't any useful information about it:
1. DFC4 is a separate module(consumes 1 slot)? Does it have any ports on it?
2. Is it a daughter card? If yes, should it be installed on supervisor or it should be installed on line cards?
I have configured the VSS in two cisco 6509-E series with only one supervisor engine, but if i configured with two supervisor engine. it is going to common mode. One supervisor engine is 3c and 3cxl.
View 2 Replies View RelatedI have an older 4006 with a Supervisor II+. We now need OSPF support, which the Sup II+ does not provide. I have access to a Supervisor III (WS-X4014), which will provide OSPF support. Question is, are there any gotchas to shutting down the switch, replacing Supervisor Engines and then powering up? What about the flash card? On my current system, it appears that I am only using bootflash: , which is where the IOS resides (see below). Since my startup config is in nvram and my IOS is in bootflash, what's the purpose of the flash card in slot0: ? and where does NVRAM and bootflash actually live on a 4006 ( on the Supervisor Engine?)
sh bootvar
BOOT variable = bootflash:cat4500-ipbase-mz.122-31.SGA11.bin,1;,1;
CONFIG_FILE variable does not exist
BOOTLDR variable does not exist
[Code].....
we got a problem with our cat4006 coreswitch. The led on the supervisorengine is red, and several errors are appearing in the message log. [code]
View 1 Replies View Related