we have installed the MSE 3350 with the lates Context Aware Sup Service from AeroscoutBut the Service still terminated because of unexpected null node message (see below)
View 7 RepliesI had upgraded the MSE to 7.0.202. Release code. The Upgrade along with the 4 database zips went smooth.But the MSE status shows following
View 2 Replies View RelatedI am trying to add 89,462+ access list rules to an ASA 5510 running 8.2(5). I have added all the rules to an object group and when I try to apply the access list to an interface it gives me the following error:
ERROR: Cannot add policy to rule engine ERROR: Unable to assign access-list wan-out to interface wan
I have not tried not using an object group and just putting the rules in the access list. I want to be able to add to these rules if needed easily.
I think it's clear that i have exceeded the rule limit for the ASA. So my question is, what is the rule limit for an ASA 5510 and which ASA could I purchase that would handle this amount of rules?
I have configured the primary firewall every thing seem to be fine, And we have configured fail over device while config is getting replicated to the fail over device we are getting below error.
ERROR: Cannot add policy to rule engine
ERROR: Unable to assign access-list LAN_out to interface inside
IOS and Model are same.But all the config got replicated from primary to secondary but except the one access group command.
access-group LAN_out in interface inside.
On an existing 4500 switch with a single sup 6-E, another sup 6-E is added. But the second sup6-E comes up as synchronised with active and in a few minutes time, reloads again. the software is 12.2(44) is the same on both sup engines. the redundancy sso output shows that slot6 is disabled.
View 1 Replies View RelatedI have recently updated one of our customer's MSE to version 7.0.105. Now for some reason the Aeroscout service will not run. I have tried starting it manually , however it stops after 10 - 15 secs.
here is partial getserverinfo output
-------------Context Aware Sub Services-------------
Sub Service Name: aeroscoutVersion: 3.2.0 - 4.0.14.14Description: AeroScout® Location Engine for RSSI and TDOA asset trackingRegistered: falseActive: false
The weird this is that I have updated our own MSE to 7.0.105 and didnt get this problem.
We have a Cisco 4404 WLC and and about 70 Cisco 1131 APs. I am very new to the Cisco WLC and I need to know how to view its AP registration and unregistration logs. We have a AP that has unregistered and we can't seem to find what switchport it was attached to. It would be useful to know the IP address and ideally any CDP information it had. Unfortunately you can only view this information in the WLC if the AP is registered, but at this point it is not.
View 2 Replies View RelatedI need to upgrade my location appliance. I am currently running a 2710, WCS version 6.0.196.0 and 21 4402 controllers on 6.0.182.0. There are 11 sites spread accross Canada and the Northern US. There are going to be a minimum of 4 more this year. The majority of my sites are outdoors and use 1522's. I have some indoor sites on 1242's, the biggest being an office building with 32 radios.The problem I have is I've hit the limit on clients that can be tracked on the 2710. For the record, I don't run rogue detection on all radios. I spread it out so that I don't get too many overlaps. I am looking at moving to the 3350 but see that the WIPS software does not include 1522's. Does that mean I lose my ability to detect disassociation floods etc if I go to the new platform? Or, does the context aware software still provide some notification.
View 5 Replies View RelatedAny info on performing this upgrade. The release notes that I have looked over make it sound like if I want to do the data migration that I must first upgrade the MSE to version 7.0.201.204 and then go to 7.0.220.0. This is only what I have come up with, this isn't clearly stated from what I have read. How to performe this upgrade with the data migration?
[URL]
Does Cisco MSE 3350 comes with two NICs. I want to configure them as a team bound to one IP address and send each to a separate 6509 switchport all in the name of redundancy and failover.
View 2 Replies View RelatedI would like to know does MSE 3350 supports HA mode,I have 2 M|SE 3350 appliance and I want to configure one as primary and second as redundent for the primary,I am not finding any documentation for the same in the cisco website.
View 2 Replies View RelatedDoes the MIR feature on the MSE 3350 requires the Context-Aware Service to work? I read that the system uses location, signal strength and coverage data in conjunction with monitor mode APs at each exit to trigger the roam. I just don't know if MIR does this on it's own or needs to get location from Context-Aware service.
View 2 Replies View RelatedIs it possible for end user to repalce the System Battary with new on, The Server is 4 Years old.
View 1 Replies View RelatedI work at a hospital and one of our department uses specialized software created by Varian Medical Systems. It has been brought to my attention that one of those applications has trouble opening during the day. I had the users demonstrate the issue and from what they explained to they are supposed to be able to open the application, log in, and be presented with a list of radiology images to choose from. Unfortunately, during the day this fails often and they have to try 3 or 4 times before it actually works. It behaves differently after 4 pm, and seems to work after the 1st or 2nd time at that time of the day. According to what I've been told this has been an issue as long as they can remember.
Varian has told me that they have done a number of things on their side to rule out their software and they think it is a network issue. We used Solar winds Engineer's Tool set (specifically the Network Performance Monitor) to monitor their switch and it is reporting no errors and the utilization graphs show that the ports involved have very little utilization. The most heavily utilized port is hovering between 10 and 5 person (Fa0/40). I've included a network diagram, but basically we have 1 10/100 Cisco 3350 switch (c3550-ipservices-mz.122-25.SEB4.bin), 4 clients, and 2 servers involved. They all are connected to the same switch at A-Full/A-100mbps. Although the Network Performance Monitor doesn't show any errors or over utilizaton of the ports in the the CLI I do see 35 output buffer failures and 35 under runs on the port connected to one of the servers (Fa0/40). They were a little higher and I cleared them about two weeks ago and then rebooted the switch, because I found that it could alleviate these types of errors.
They say the software use ports 5000, 55000, 55010, and 55020. We tried a packet capture, but I didn't have enough experience/knowledge to get anything useful out of it. I also checked the event logs on the clients and servers and nothing there indicates a issue in the software. They want us to replace the switch with a gigabit switch, but we have a REALLY limited budget and I would rather not if it isn't necessary. What I could try in order to rule out the network?
I have a dell vostro 3350. I use it with both Windows and Linux OS (Mint, Ubuntu).
Recently I faced an issue with my motherboard (I guess it was a matter of short-circuit) so I called the Dell assistance and they quickly came out and substitute my motherboard. After that intervention, my wi-fi and figerprint reading stopped working at all. So I called again Delle assistance and they substituted both the wi-fi and the fingerprint reader. Everything seemed to work fine... since my PC went in hibernate mode.
In fact now the wi-fi card is disabled (not even seen by the OS) after the PC goes in sleep/hibernate mode or even if it is turned off and than on again. I need to turn off and on the PC at least one more time the PC in order to make the wi-fi card found (and working) again.
I checked with all the three OS I have in my PC so I guess the issue isn't related to the drivers. On the other hand, it looks like the wi-fi works totally fine... when it works. It is quite a systematic effect and not related to bumps or mechanical sullicitations, so I guess it is not a matter of wrongly-connected card either..
I am able to ping the ACS ENGINE 4.2 from any PC or device. But I am not able to ping any device from the box while logged in via SSH. while I can do so while logged in via console. Is this some kind of bug or is there any patch which after installing will allow me to ping devices from ACS SSH sessions.
View 3 Replies View RelatedIn my existing production router 7609 of my company, sup-engine already fixed in slot 5 with SRC2 12.2(33) IOS and I need to insert another sup engine in slot 6 with SRE7 IOS code image and after this, again sup engine in slot 5 must be with SRE7 IOS image...(also I have extra sup engines with SRE 7 code image ready with me) Query:i am going to offload router before proceed for this activity?i will insert new sup engine in slot 6 with SRE 7 ios image and now i need to re-install spare sup engine with SRE 7 code readily available with me by removing existing sup engine from slot 5 (Active) so what will be the proceedure to insert new sup engine with SRE 7 code in slot 5 and slot 6 with minimum downtime of router?
existing setup sup engine in slot 5 with SRC2 12.3 (old hardware) slot 6 is EMPTY
final result should be like this: sup engine in slot 6 with SRE 7 (new hardware)
sup engine in slot 5 with SRE 7 (new hardware)
I have supervisor engine ws-x4516 with two line card WS-X4424 - GB - RJ45 - 1No ,WS-X4548 - GB - RJ45 - 1No. Now i want switch and hardware redundancy.
View 3 Replies View RelatedIn my test lab , I have a CISCO 1841 with a AIM-VPN/BPII-PLUS board , everything was working fine , until I would like to see the difference with and without the accelerator.Sins the moment that the IOS told me that he will change to SW accelerator instead of HW accelerator , I can not make it work anymore.I have a copy of the full working configuration before I did this , I have put it back on my router but still NO VPN. [code]
View 2 Replies View Relatedcan I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View RelatedI have a cisco 7609 with sup engine 720, I want to implement VPLS for that I purchased a 7600-ES+20G3C with the adv license 76-ES+ADVIP-LIC in a separate pak?how to activate the license on the 7609.
View 3 Replies View RelatedI have an inventory added to Ciscoworks and am getting alerts on interfaces that I want to exclude but for the life of me I can't figure out how to exclude interfaces. Any tips on how to exclude interfaces from the fault engine in 4.1.
View 3 Replies View RelatedMy existing 4006 chassis is using Supervisor III (WS-X4014). I have another 4506 chassis using Supervisor IV (WS-X4515) and a Net flow Services Card (WS-F4531) build on top of it.
I need Net flow Services Card in 4006, so can I just replace the Supervisor IV (WS-X4515) used in Cisco 4006? Is it compatible with 4006?
I am currently running a 4506 with a sup V engine. I have purchased a sup 7 engine. Is there a guide on how to perform this task. I am sure I need to do an IOS update as well.
View 2 Replies View Relatedi have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies View RelatedRemoving and Installing a Supervisor Engine on a cisco router 7690 and more important IOS upgrade of this module.
I need some kind of manual, but I would prefer a short procedure to do this change. A brief of the steps to do that. Also i don't if i have to upgrade the new module after install it.
PD.
IP7VAL02#sh modMod Ports Card Type Model Serial No.--- ----- -------------------------------------- ------------------ ----------- 1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1034Z32J 2 48 CEF720 48 port 10/100
[Code]....
I have a strange issue with 4500 E chassis loaded with SUP 7L-E which always remains in ORANGE LED status, also the uplink ports interface is down and the line protocol is down but when i execute the command sh int gig1/5 it show me the media type sfp but there is no red laser light seen in the sfp transiever,The below command is configured for the uplink gig port on the SUP engine.hw-module uplink select gigabitethernet?
View 10 Replies View Relatedto the above question. I see the specs for the WS-SUP720-3B and 3BXL but not the WS-SUP720-BASE with the MSFC3 and PFC3A daughter cards.The 3B can handle 256,000 routes using IPv4 and the 3BXL can do 1,000,000.
View 4 Replies View RelatedI have recetly upgraded our core switches (6509E) to SUP 2T from 32. Each core has 2 SUP's (hot/standby). out of 4 SUP engines, one is defective. i had received the new SUP from cisco. Currently my core swicth 2 is running with single SUP. Can i directly insert the new SUP engine in slot 6 (free)? will it automatically load the existing IOS from active SUP? what will happen if the new SUP has a different IOS other than the active SUP? Also is there a way to find out the IOS version without inserting in the chasy?
View 2 Replies View RelatedIs the ISE going to support the 2500 series Wireless LAN Controller WLC? If yes in what release and appriximately when is that due to be released?
View 1 Replies View Relatedi cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedI have Cisco Catalyst 2901 switch with Sup engine which have CatOS installed. I want to know that can I install Cisco IOS in this switch.
View 1 Replies View RelatedI would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before
View 5 Replies View Related