Cisco :: 1522 APs And 3350 MSE Upgrade
Mar 3, 2011
I need to upgrade my location appliance. I am currently running a 2710, WCS version 6.0.196.0 and 21 4402 controllers on 6.0.182.0. There are 11 sites spread accross Canada and the Northern US. There are going to be a minimum of 4 more this year. The majority of my sites are outdoors and use 1522's. I have some indoor sites on 1242's, the biggest being an office building with 32 radios.The problem I have is I've hit the limit on clients that can be tracked on the 2710. For the record, I don't run rogue detection on all radios. I spread it out so that I don't get too many overlaps. I am looking at moving to the 3350 but see that the WIPS software does not include 1522's. Does that mean I lose my ability to detect disassociation floods etc if I go to the new platform? Or, does the context aware software still provide some notification.
View 5 Replies
ADVERTISEMENT
Jan 18, 2012
Any info on performing this upgrade. The release notes that I have looked over make it sound like if I want to do the data migration that I must first upgrade the MSE to version 7.0.201.204 and then go to 7.0.220.0. This is only what I have come up with, this isn't clearly stated from what I have read. How to performe this upgrade with the data migration?
[URL]
View 1 Replies
View Related
Sep 30, 2012
I up graded to latest f/w. Now I can only log into the unit for about 1 minute before a get a limited connectivity warning, then it boots me out.
View 7 Replies
View Related
Dec 14, 2010
I upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
[url]...
View 6 Replies
View Related
Mar 26, 2009
Does Cisco MSE 3350 comes with two NICs. I want to configure them as a team bound to one IP address and send each to a separate 6509 switchport all in the name of redundancy and failover.
View 2 Replies
View Related
Apr 20, 2010
we have installed the MSE 3350 with the lates Context Aware Sup Service from AeroscoutBut the Service still terminated because of unexpected null node message (see below)
View 7 Replies
View Related
Aug 17, 2011
I had upgraded the MSE to 7.0.202. Release code. The Upgrade along with the 4 database zips went smooth.But the MSE status shows following
View 2 Replies
View Related
Feb 6, 2011
I would like to know does MSE 3350 supports HA mode,I have 2 M|SE 3350 appliance and I want to configure one as primary and second as redundent for the primary,I am not finding any documentation for the same in the cisco website.
View 2 Replies
View Related
Oct 21, 2009
Does the MIR feature on the MSE 3350 requires the Context-Aware Service to work? I read that the system uses location, signal strength and coverage data in conjunction with monitor mode APs at each exit to trigger the roam. I just don't know if MIR does this on it's own or needs to get location from Context-Aware service.
View 2 Replies
View Related
Sep 8, 2011
Is it possible for end user to repalce the System Battary with new on, The Server is 4 Years old.
View 1 Replies
View Related
Jan 21, 2013
I work at a hospital and one of our department uses specialized software created by Varian Medical Systems. It has been brought to my attention that one of those applications has trouble opening during the day. I had the users demonstrate the issue and from what they explained to they are supposed to be able to open the application, log in, and be presented with a list of radiology images to choose from. Unfortunately, during the day this fails often and they have to try 3 or 4 times before it actually works. It behaves differently after 4 pm, and seems to work after the 1st or 2nd time at that time of the day. According to what I've been told this has been an issue as long as they can remember.
Varian has told me that they have done a number of things on their side to rule out their software and they think it is a network issue. We used Solar winds Engineer's Tool set (specifically the Network Performance Monitor) to monitor their switch and it is reporting no errors and the utilization graphs show that the ports involved have very little utilization. The most heavily utilized port is hovering between 10 and 5 person (Fa0/40). I've included a network diagram, but basically we have 1 10/100 Cisco 3350 switch (c3550-ipservices-mz.122-25.SEB4.bin), 4 clients, and 2 servers involved. They all are connected to the same switch at A-Full/A-100mbps. Although the Network Performance Monitor doesn't show any errors or over utilizaton of the ports in the the CLI I do see 35 output buffer failures and 35 under runs on the port connected to one of the servers (Fa0/40). They were a little higher and I cleared them about two weeks ago and then rebooted the switch, because I found that it could alleviate these types of errors.
They say the software use ports 5000, 55000, 55010, and 55020. We tried a packet capture, but I didn't have enough experience/knowledge to get anything useful out of it. I also checked the event logs on the clients and servers and nothing there indicates a issue in the software. They want us to replace the switch with a gigabit switch, but we have a REALLY limited budget and I would rather not if it isn't necessary. What I could try in order to rule out the network?
View 4 Replies
View Related
Feb 17, 2013
I have a dell vostro 3350. I use it with both Windows and Linux OS (Mint, Ubuntu).
Recently I faced an issue with my motherboard (I guess it was a matter of short-circuit) so I called the Dell assistance and they quickly came out and substitute my motherboard. After that intervention, my wi-fi and figerprint reading stopped working at all. So I called again Delle assistance and they substituted both the wi-fi and the fingerprint reader. Everything seemed to work fine... since my PC went in hibernate mode.
In fact now the wi-fi card is disabled (not even seen by the OS) after the PC goes in sleep/hibernate mode or even if it is turned off and than on again. I need to turn off and on the PC at least one more time the PC in order to make the wi-fi card found (and working) again.
I checked with all the three OS I have in my PC so I guess the issue isn't related to the drivers. On the other hand, it looks like the wi-fi works totally fine... when it works. It is quite a systematic effect and not related to bumps or mechanical sullicitations, so I guess it is not a matter of wrongly-connected card either..
View 5 Replies
View Related
Mar 9, 2012
Have a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies
View Related
Sep 13, 2012
How could I add an AP 1522 ag without DHCP. How do I setup the IP address configuration? For some electrical problem I lost 4 1522 APs. I have two controllers and a windows server running WCS. Now I have just one AP up and running. After booting a new AP I could not get in "config mode" via console so I tryied to setup the IP config as follows (pressing ESC key during the boot):
set IP_ADDR 10.1.1.100
set NETMASK 255.255.255.0
set DEFAULT_ROUTER 10.1.1.1.1
then: "boot"
*** I have authorized the new AP in "MAC address filtering" via WCS.
*WCS version 7.0.164.0
I think that is no request reaching the controllers.
View 5 Replies
View Related
Mar 19, 2012
After a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
View 1 Replies
View Related
Mar 10, 2013
My D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies
View Related
May 13, 2010
I'm facing the following doubt regarding the AC Power Connector on the 1522 AP.We are powering up the AP through PoE, so the AC Power Connector is not used.BUT,do i have to seal/protect the connector or leave it as is?
View 3 Replies
View Related
Mar 25, 2012
I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
View 1 Replies
View Related
May 21, 2013
I have a wireless sytem with a WLC 4400 and several 1522 Access Points. They don't actually function as Access Points because I'm using radio communication only for backhaul. There are no clients connected to the Access Points. All traffic on the network comes from the devices connected on the LANs that are bridged through the APs ethernet port.
I would like to create filters to allow only certain devices to be able to transmit over the radio link. I've used this in the past on 1310 units and it was very easy to do via GUI. This filter could be either by IP or MAC Addresses. IP would be better for me.
View 1 Replies
View Related
Sep 29, 2011
I have two Windows 7 computers and neither one will successfully upgrade a 1242 AP to LWAP. However, I go to a coworker's XP machine and run the tool without issues. On Windows 7 I keep receiving the error message of ACL or Firewall is blocking. I have added rules and then even tried disabling the firewalls completely on both computers and still no success.
View 7 Replies
View Related
Apr 18, 2012
I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.
View 3 Replies
View Related
Sep 30, 2011
I recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies
View Related
Apr 26, 2011
My problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
View 4 Replies
View Related
Mar 12, 2012
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
View 3 Replies
View Related
Dec 7, 2011
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
View 4 Replies
View Related
Aug 27, 2010
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
View 14 Replies
View Related
Mar 14, 2012
I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies
View Related
Jan 20, 2011
I have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.
LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2
View 2 Replies
View Related
Nov 29, 2010
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
View 14 Replies
View Related
May 25, 2012
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
View 3 Replies
View Related
Feb 14, 2012
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies
View Related
Jan 10, 2012
my config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :
- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?
- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?
View 7 Replies
View Related
Aug 8, 2011
Will the dap-1522 work with 3d video ie; from a 3d Blue Ray Player? I am upgrading system to an LED Samsung 3D TV and Samsung 3d Blue Ray Player. I know that HDMI 1.4 cables will work but am looking at the wireless option.
View 1 Replies
View Related
