Cisco Wireless :: 1522 MAP Through 1042 RAP Not Working?
Mar 25, 2012
I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
View 1 Replies
ADVERTISEMENT
Feb 14, 2012
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies
View Related
Dec 4, 2011
I am unable to connect and Android device (HTC Desire, Samsung Nexus S etc) wirelessly to the DAP-1522. I've search through the forums and can't find anyone else having issues with Android so I think it must be one of my settings. It works fine if I switch to WEP however I don't want to use the weaker hackable protocol. Any way to have the DAP-1522 in WPA working with an android device?
View 4 Replies
View Related
Sep 20, 2012
Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies
View Related
Nov 27, 2011
I have an Aironet 1042 wireless AP if I create an SSID with no security it shows up as wireless N when I see it on a windows 7 laptop. As soon as I apply any security settings is shows up as G and not N. I just want to be able to authenticate with a Windows 2008 server running NPS - this works fine but I obviously want to connect at N speed and not G.
View 13 Replies
View Related
May 16, 2013
I have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies
View Related
Jul 11, 2012
i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
View 5 Replies
View Related
May 21, 2013
2504 WLC, 1042 AP's
I have my NPS server setup, Group Policy, Certs (RAS+IAS), DHCP option 43, DNS A record
If I look in the event viewer on NPS, it says
Log Name: Security Source: Microsoft- Windows -Security -Auditing Date: 5/22/2013 12:36:37 PM
Event ID: 6272Task Category: Network Policy Server Level: Information Keywords: Audit Success User: N/A Computer: mfs1.Mitchell. internal Description:Network Policy Server granted access to a user.
[Code] .....
But the laptop won't connect or get an IP.
View 30 Replies
View Related
Dec 14, 2011
What dbm or mw each of the power local settings are? I see on a 1042 from -1 thru 20 and am assuming 20dBm is 100mW.
OM-ess-lab-WLAN1(config-if)#power local ?
<-1 - 20> One of : -1 2 5 8 11 14 17 20 maximum Set power to allowed maximum
View 6 Replies
View Related
Jan 24, 2013
Do the 1042 Autonomous APs support GRE tunnels?
View 4 Replies
View Related
Apr 25, 2013
I got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?
View 24 Replies
View Related
Sep 18, 2012
There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
View 3 Replies
View Related
Jul 21, 2012
I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
View 4 Replies
View Related
Apr 8, 2012
this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
View 2 Replies
View Related
Nov 29, 2012
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
View 4 Replies
View Related
Jan 6, 2011
I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies
View Related
Jun 11, 2012
I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
View 2 Replies
View Related
Feb 13, 2013
I am trying to configure a Cisco 1042 autonomous AP and have ran into some problems. I require 2 broadcasted SSIDs that use WPA v2. When I only have 1 of the SSIDs enabled, I can authenticate with no problems. When I have both SSIDs enabled, I can connect to one of the networks, but not the other. I have verified the PSK multiple times, but the logs still show dot11-7-auth_failed. If I remove the working SSID and make no changes to the SSID for which authentication previously fails, everything works fine. Upon adding the other SSID back, I run into the same authentication issue.
View 3 Replies
View Related
Mar 1, 2013
We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
I would like to use LDAP or ACS for authentication purpose.
View 3 Replies
View Related
Apr 6, 2012
I want buy an Access point which cover 300 Meter coverage Area.
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.
View 8 Replies
View Related
May 3, 2012
We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies
View Related
Oct 25, 2012
In my class room, a lot of new Dell notebook (university purchased) all of those are the same model. Those came with 2.4&5Ghz WLAN NIC.
So, my WLC-based AP in that room which is Cisco 1x1042 & 1x1252 running in light-weight.This make huge congest on 5 Ghz. All of my 41 NB go for 5Hgz. And Zero client on 2.4Ghz radio, 2.4Ghz is not utilized at all.
I have read a lot of those related discussion. But I even can not find one that need to utilized BOTH of band. Most of those discussion talking to band-select which is "this feature only goes in one direction from the 2.4 GHz range to the 5 GHz not visa-versa."
My constrint is We can not touch the NB. Because this is university, much many diverse user loging in.
View 7 Replies
View Related
Mar 19, 2012
I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies
View Related
Apr 30, 2012
My access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies
View Related
Oct 12, 2011
We use LAP 1042's as our main AP's, and we set those in H-REAP (with Local Switching) in order to let them work properly. This is because our WLC is not located in the AP's local network. This is something that, sadly, cannot change, so this has to stay the way it is now.We also use a freeradius server to authenticate users on our wireless network. In our previous situation, before using Cisco appliances, we would just set our web auth page to a certain URL and make sure that the URL was granted access before authentication. We obviously found out that Cisco implemented this by using a Pre-Auth ACL. As a result we've added the IP adres of that web login page to a ACL and added that ACL to the pre-auth for the WLAN that will use Radius Web Auth. The WLAN also has the Radius servers added to the AAA page, so those are in place.
Now comes the problem though. When I connect to the WLAN that will have to use Radius, and try to open a page it will start trying to load the virtual interface (1.1.1.1) and then it will try to redirect to the web-page that I defined in the External Server. Like I stated, I've added the webpage's IP adres (after resolving it) to the pre-Auth ACL, and when I look at the counters I see that go up every time I try to load a page. Yet the browser on the computer gives me a time-out trying to load the external web-server web auth page.
When I disable Web-Auth all-together, I get internet straight away, so the problem obviously is located in the web-auth settings or ACL settings somewhere, but at this point I just don't know where to look anymore.
View 6 Replies
View Related
Mar 9, 2012
Have a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies
View Related
Mar 19, 2012
After a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
View 1 Replies
View Related
May 13, 2010
I'm facing the following doubt regarding the AC Power Connector on the 1522 AP.We are powering up the AP through PoE, so the AC Power Connector is not used.BUT,do i have to seal/protect the connector or leave it as is?
View 3 Replies
View Related
May 21, 2013
I have a wireless sytem with a WLC 4400 and several 1522 Access Points. They don't actually function as Access Points because I'm using radio communication only for backhaul. There are no clients connected to the Access Points. All traffic on the network comes from the devices connected on the LANs that are bridged through the APs ethernet port.
I would like to create filters to allow only certain devices to be able to transmit over the radio link. I've used this in the past on 1310 units and it was very easy to do via GUI. This filter could be either by IP or MAC Addresses. IP would be better for me.
View 1 Replies
View Related
Apr 18, 2012
I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.
View 3 Replies
View Related
Sep 26, 2012
I connected AP 1522 to AC power source and this is the message that i received on the console port.
%CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (0000.0000.0000)
Why this message apear ?This is not sufficient power to bring up radio interfaces?
View 5 Replies
View Related
Sep 5, 2012
They brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
View 14 Replies
View Related
Jun 13, 2013
Client has existing 1522 outdoor access points over different branches.1522 is dicontinued and 1552 is the replacement AP.Client intends to extend their outdoor wireless with the new AP's.Are there any known issues if the 1552 is mixed with 1522 envi?,Is a separate controller required for the new AP's?Will MESH work between 1522 and 1552 AP's?
View 3 Replies
View Related
