Cisco Wireless :: WLC 2112 With 1042 Mesh APs?
May 16, 2013I have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: Power Requirements For 1042 Mesh Network
Apr 8, 2012this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
Cisco Wireless :: 2112 WLC Using All Of 5.0 Ghz Channel?
Sep 25, 2012I have a 2112 wlc and 6 1142ap's. I noticed that the 2.4ghz channel is filled with lots of networks but the 5.0ghz area is empty. I tried to manually change the channel but it keeps reverting back to 2.4.
View 11 Replies View RelatedCisco Wireless :: Configure WLC 2112 With LAP 1042N?
Jan 4, 2012we are trying to configure WLC 2112 with LAP 1042 but getting following erros on LAP1042. It show the Ap is not supported in controller version 6.0.199.4
*Jan 5 16:52:13.397: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.2.101 peer_port: 5246*Jan 5 16:52:13.398: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.2.101*Jan 5 16:52:13.399: %CAPWAP-
[Code]....
Cisco Wireless :: Enable Mode On 2112 WLC?
Nov 8, 2012Do we have enable mod eon 2112 WLC ? Also if we need to access WAP from WLC how can we telnet or ssh?
View 5 Replies View RelatedCisco Wireless :: 2112 Controller Cluster
May 10, 2012My company has a lot of thier business relying on the wireless network and I am trying to reduce the single points of failulre in my network infrastructure. We have a single Cisco 2112 controller with 10 AP's that I am wondering if it's possible to cluster this with another controller for redundancy purposes?
View 3 Replies View RelatedCisco :: 2112 Wireless LAN Controller And Apple TV Airplay
Jan 2, 2012I am having a trouble with using iTunes, iPhones and iPads on our Wireless LAN. We have the 2112 WLC and 10 1142N WAPs. If I do a network scan, I can see the Apple TV and see that port 5353 is open, which is Apple's Bonjour service. However, if I try to play music/video in iTunes, or on an iPhone/iPad, I do not see the Airplay icon. If I plug into the LAN, the Airplay icon appears immediately. I have created an allow all rule in the ACL but still no dice.
View 26 Replies View RelatedCisco Wireless :: WLC 2112 - Access Points Are Not Running On Same SSID
Mar 11, 2012I have 8 no. AIR-LAP1131AG-A-K9 and WLC 2112 Wireless LAN Controller,i configured the device and its working at deffent SSIDs but when i am trying to enable same SSID on all LAP it shows "AP on dupplicate SSID found and Layer 2 security found".
View 1 Replies View RelatedCisco Wireless :: 2112 / Use Windows IAS To Validate WLC Management Users?
Feb 8, 2011I am having a problem using my Windows IAS radius server to validate management users for my 2112 Wireless Lan Controller.I have defined the radius server and it works ok with the policy for validating wireless clients but not for WLC management users.The Remote access policy seems to be set up correctly as the event viewer on the server shows:-
Event Type: InformationEvent Source: IASEvent Category: NoneEvent ID: 1Date: 09/02/2011Time: 11:06:06User: N/AComputer: UK01DC07Description:User xxxxxx was granted access. Fully-Qualified-User-Name = TRAVEL.OAG.com/Dunstable Admins/xxxxxx NAS-IP-Address = 10.10.45.210 NAS-Identifier = UK03NM01 Client-Friendly-Name = UK03NM01 Client-IP-Address = 10.10.45.210 Calling-Station-Identifier = <not present> NAS-Port-Type = <not present> NAS-Port = <not present> Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = <undetermined> Policy-Name = UK03NM01 - login Authentication-Type = PAP EAP-Type = <undetermined>
....
But, the WLC log shows:
*Feb 09 11:06:06.612: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed. User:xxxxxx. Service-Type is not present or it doesn't allow READ/WRITE permission..
The WLC just returns the login screen
Cisco Wireless :: WLC 2112 Aren't Able To Connect To Any Of WLAN / APs Will Disassociate
Mar 21, 2012We recently purchased a 2112 WLC, running version 6.0.199.4. I have everything running through a single port on the controller, which is connected to a trunk port on our 3750 stack. Our management VLAN is vlan 40, and AP is plugged into another port on the same switch which is an access port in vlan 40. APs appear in the controller ok, receive an IP address, but we aren't able to connect to any of the WLANs and periodically the APs will disassociate with the following messages: [code] I'm not sure if that's related to why we can't connect to the WLANs or not...
Another wrinkle is that if we plug in the AP directly to one of the PoE ports on the controller, it all works perfectly. I'm guessing its something switch-related since the only difference is that we're not going through the switch when it works.
Cisco Wireless :: 2112 - How To Change RTS Threshold In WLAN Controllers
Jan 18, 2010I've read some opinions that lowering the RTS threshold can facilitate in some noisy wireless environments. I have found how this can be done on standalone APs but cant seem to implement the change on a WLC 2112. How to do it.
View 3 Replies View RelatedCisco Wireless :: 2112 - Client Disconnection And Varying Signal Strength
Dec 16, 2012We are having a 2112 WLC and LAP1042 access points and facing a client disconnection issue. Also signal strength is varying even when client is at steady position. We have a single SSID structure and clients are connecting through 802.1x authentication with WPA2. Access points are joined in H-REAP mode. We also tried by creating a new SSID with open authentication and even on that SSID signal stregnth is varying and client is getting limited connectivity. Attached are the debugs for a particular client and the show tech support for WLC.
View 5 Replies View RelatedCisco Wireless :: 2112 One Ssid To Multiples Vlan Without Hreap Flex Connect
May 22, 2013I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies View RelatedCisco Wireless :: Can 2 Aironet 1042 Use WDS Without Controller?
Sep 20, 2012Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies View RelatedCisco Wireless :: 1522 MAP Through 1042 RAP Not Working?
Mar 25, 2012I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
Cisco :: Aironet 1042 Wireless N Not Broadcasting?
Nov 27, 2011I have an Aironet 1042 wireless AP if I create an SSID with no security it shows up as wireless N when I see it on a windows 7 laptop. As soon as I apply any security settings is shows up as G and not N. I just want to be able to authenticate with a Windows 2008 server running NPS - this works fine but I obviously want to connect at N speed and not G.
View 13 Replies View RelatedCisco Wireless :: WDS On Aironet 1042 Autonomous AP?
Jul 11, 2012i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
Cisco Wireless :: 2504 WLC / 1042 AP - Client Not Connecting
May 21, 20132504 WLC, 1042 AP's
I have my NPS server setup, Group Policy, Certs (RAS+IAS), DHCP option 43, DNS A record
If I look in the event viewer on NPS, it says
Log Name: Security Source: Microsoft- Windows -Security -Auditing Date: 5/22/2013 12:36:37 PM
Event ID: 6272Task Category: Network Policy Server Level: Information Keywords: Audit Success User: N/A Computer: mfs1.Mitchell. internal Description:Network Policy Server granted access to a user.
[Code] .....
But the laptop won't connect or get an IP.
Cisco Wireless :: Power Local Settings On 1042?
Dec 14, 2011What dbm or mw each of the power local settings are? I see on a 1042 from -1 thru 20 and am assuming 20dBm is 100mW.
OM-ess-lab-WLAN1(config-if)#power local ?
<-1 - 20> One of : -1 2 5 8 11 14 17 20 maximum Set power to allowed maximum
Cisco Wireless :: Do 1042 Autonomous APs Support GRE Tunnels
Jan 24, 2013Do the 1042 Autonomous APs support GRE tunnels?
View 4 Replies View RelatedCisco Wireless :: 1042 - New AP Not Showing In Default Group?
Apr 25, 2013I got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?
View 24 Replies View RelatedCisco Wireless :: Captive Portal On AP 1041 / 1042
Sep 18, 2012There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
Cisco Wireless :: 2504 - 1042 AP Registration With Controller
Jul 21, 2012I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
Cisco :: Unable To Join Wireless AP 1042 With 2106 Controller?
Nov 29, 2012I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
Cisco Wireless :: Capability To Downgrade AP 1042 From CAPWAP To Autonomous?
Jan 6, 2011I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies View RelatedCisco Wireless :: 1042 LAP With 5508 Series Controller - AP Will Not Associate
Jun 11, 2012I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
Cisco Wireless :: 1042 Autonomous AP - BSSID Failed Authentication
Feb 13, 2013I am trying to configure a Cisco 1042 autonomous AP and have ran into some problems. I require 2 broadcasted SSIDs that use WPA v2. When I only have 1 of the SSIDs enabled, I can authenticate with no problems. When I have both SSIDs enabled, I can connect to one of the networks, but not the other. I have verified the PSK multiple times, but the logs still show dot11-7-auth_failed. If I remove the working SSID and make no changes to the SSID for which authentication previously fails, everything works fine. Upon adding the other SSID back, I run into the same authentication issue.
View 3 Replies View RelatedCisco Wireless :: Implement 2504 WLC And 1042 Access Points?
Mar 1, 2013We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
I would like to use LDAP or ACS for authentication purpose.
Cisco Wireless :: Access Point Coverage Area 1042
Apr 6, 2012I want buy an Access point which cover 300 Meter coverage Area.
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.
Cisco Wireless :: 1041 / 1042 - Apple Ipad Intermittent Wi-Fi Connectivity?
May 3, 2012We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies View RelatedCisco Wireless :: 2.4 / 5Ghz Load Balancing Utilize On Both 1042 And 1252
Oct 25, 2012In my class room, a lot of new Dell notebook (university purchased) all of those are the same model. Those came with 2.4&5Ghz WLAN NIC.
So, my WLC-based AP in that room which is Cisco 1x1042 & 1x1252 running in light-weight.This make huge congest on 5 Ghz. All of my 41 NB go for 5Hgz. And Zero client on 2.4Ghz radio, 2.4Ghz is not utilized at all.
I have read a lot of those related discussion. But I even can not find one that need to utilized BOTH of band. Most of those discussion talking to band-select which is "this feature only goes in one direction from the 2.4 GHz range to the 5 GHz not visa-versa."
My constrint is We can not touch the NB. Because this is university, much many diverse user loging in.
Cisco Wireless :: 1042 - Convert Light Weight AP To Autonomous Mode?
Mar 19, 2012I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies View RelatedCisco Wireless :: Access Point 1042 Series In Light Weight Mode Reloads Itself
Apr 30, 2012My access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies View Related