What dbm or mw each of the power local settings are? I see on a 1042 from -1 thru 20 and am assuming 20dBm is 100mW.
OM-ess-lab-WLAN1(config-if)#power local ?
<-1 - 20> One of : -1 2 5 8 11 14 17 20 maximum Set power to allowed maximum
this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
I am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies View RelatedWhat do the broadcom power saving mode settings mean? If power saving mode is enabled, what is the time it takes to go into power saving mode? What does fast mean?
View 1 Replies View RelatedWe hav ea 5508 pair running in HA mode. Initially the conrollers were running the 73..101.0 code. We were having issues where the primary controller would software reset (according to show sysinfo), the secondary (HA SKU) would take over and then after a few hours the secondary would also software reset and the primary would take over. Also I notice that after this happens that the Tx Power Control doesn't seem to adjust the A radio settings, most of the radios are at the 6 level. Normally they are 1, 2, or 3. Last week I upgraded to 7.3.112.0, later that day the same thing happened.
View 1 Replies View RelatedEverything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
I upgraded my 3602i survey ap the other day to the public image the other day and I have to say.. I've got it up and going of course, but I have a concern on the transmit power settings. Originally, the only option it gave me was MAX and -4, which I hadn't seen before, interesting.. -4 of what? 20? 17 probably or I though? At any rate, I went into the CLI to set the power manually, no issues there, though my options are not what I expected, maxing out at 25mw basically, which is fine but.. in setting it manually in CLI, the web interface reports an Error on transmit power. So.. does this work or not? Any survey with this image to verify it's power settings? 15.2(23c)
View 3 Replies View RelatedI have the DIR-655 (H/w Ver B1, F/W Ver 2.05NA) set up as router on my network (TWC/RR - modem is Motorola SURFBoard 6121 - modem only, no router or other services provided). I have configured the router sufficiently to allow all computers on the local network to access the Internet, and have configured the DHCP server on the router to provide IP addresses to the local network. I have configured the router to provide the DNS addresses for my local DNS resolvers (so that I can provide DNS resolution for an "internal" domain). Configuration specifics available on request, but everything mentioned so far is working satisfactorily, at least so far.
So, my question: The "Local Domain Name" setting on the router, as indicated in the documentation, provides a connection-specific domain name when DHCP supplies an IP address to the local system. This setting, however, is overridden if the ISP provides a domain name when it assigns an IP to the WAN connection. I have verified by experiment that this is true (no matter what I put in the Local Domain Name field - whether a valid domain, or blank - the local machines receive the domain name supplied by the ISP.I wish to modify this behavior. I wish to have the router provide the domain name specified in the Local Domain Name field *regardless* of what the ISP provides.
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)However ...when powering off (and back on) the device , my Dreambox Sattelite units (DM500) could not get access to the internet anymore (outbound) on port 12000.All other internet traffic went fine ...through browser, wireless, ...all Ok.....I tried everything to resolve but ultimately only succeeded in re-configuring from sracth. powered off the device and brought it back up ....same symptons.Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all Ok again .....until I powered the device off and back on .....I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dreambox unit directly to the device) and ....same symptons ....when powering off/on, the dreambox cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works Ok ). ? It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ?
View 5 Replies View RelatedOur DIR-615 has started freezing and when reset (power cycled), it reverts to factory settings.This has been running 24/7 for several months with no problem. Three days in a row now I've woken up to find our home network is down and the DIR-615 status lights are "yellow". Power cycling the DIR615 resolves the problem however the DIR-615 looses its settings, reverting to factory defaults (looses the admin password, wireless settings, etc). I can reload the settings from a file saved on my computer but needless to say, this is a bit annoying. I don't believe there are any wireless clients connected at the time as most of the wireless is served by an airport two floors up. There are several wired devices always connected:
a Zoom ATA carrying our "land line"
a tivo (doing whatever tivo boxes do)
a SSL based Voip phone (different than the zoom ata)
an AirPort Express 802.11n (bridge mode) which may have a couple of wireless clients
a laptop which may or may not be sleeping at the time
There are a couple of ethernet switches in the network.Some of the devices acquire addresses via DHCP, others are assigned fixed addresses outside the range of the DHCP addresses served by the DIR-615.Nothing has changed on the network in months.
The only settings I've messed with on the DIR-615 are:
a) set the admin/user passwords
b) Set the wireless network name, enable WPA, set the WPA Key
c) enabled ntp (this is now disabled and I've set the time manually)
d) Change the network base from 192.168.0. to 192.168.4.
The DIR-615 is hardware rev E3, Firmware 5.10 The cable modem (from RCN) is a Scientific American model DPC2100R2
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)
However ...when powering off (and back on) the device , my Dream box Satellite units (DM500) could not get access to the internet anymore (outbound) on port 12000.
All other internet traffic went fine ...through browser, wireless, ...all OK.....I tried everything to resolve but ultimately only succeeded in re-configuring from scratch. This solved the issue .....until ....right...I powered off the device and brought it back up ....same symptoms. Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all OK again .....until I powered the device off and back on .....
I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dream box unit directly to the device) and ....same symptoms ....when powering off/on, the dream box cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.
And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works OK ). It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ? (and ...no...I did not setup any port forwarding not triggering.
Missing local area connection icon in network connection after power failure?
View 1 Replies View RelatedCan 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies View RelatedI'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
I have an Aironet 1042 wireless AP if I create an SSID with no security it shows up as wireless N when I see it on a windows 7 laptop. As soon as I apply any security settings is shows up as G and not N. I just want to be able to authenticate with a Windows 2008 server running NPS - this works fine but I obviously want to connect at N speed and not G.
View 13 Replies View RelatedI have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies View Relatedi'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
2504 WLC, 1042 AP's
I have my NPS server setup, Group Policy, Certs (RAS+IAS), DHCP option 43, DNS A record
If I look in the event viewer on NPS, it says
Log Name: Security Source: Microsoft- Windows -Security -Auditing Date: 5/22/2013 12:36:37 PM
Event ID: 6272Task Category: Network Policy Server Level: Information Keywords: Audit Success User: N/A Computer: mfs1.Mitchell. internal Description:Network Policy Server granted access to a user.
[Code] .....
But the laptop won't connect or get an IP.
Do the 1042 Autonomous APs support GRE tunnels?
View 4 Replies View RelatedI got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?
View 24 Replies View RelatedThere is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies View RelatedI have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
I am trying to configure a Cisco 1042 autonomous AP and have ran into some problems. I require 2 broadcasted SSIDs that use WPA v2. When I only have 1 of the SSIDs enabled, I can authenticate with no problems. When I have both SSIDs enabled, I can connect to one of the networks, but not the other. I have verified the PSK multiple times, but the logs still show dot11-7-auth_failed. If I remove the working SSID and make no changes to the SSID for which authentication previously fails, everything works fine. Upon adding the other SSID back, I run into the same authentication issue.
View 3 Replies View RelatedWe have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
I would like to use LDAP or ACS for authentication purpose.
I want buy an Access point which cover 300 Meter coverage Area.
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.
We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies View RelatedIn my class room, a lot of new Dell notebook (university purchased) all of those are the same model. Those came with 2.4&5Ghz WLAN NIC.
So, my WLC-based AP in that room which is Cisco 1x1042 & 1x1252 running in light-weight.This make huge congest on 5 Ghz. All of my 41 NB go for 5Hgz. And Zero client on 2.4Ghz radio, 2.4Ghz is not utilized at all.
I have read a lot of those related discussion. But I even can not find one that need to utilized BOTH of band. Most of those discussion talking to band-select which is "this feature only goes in one direction from the 2.4 GHz range to the 5 GHz not visa-versa."
My constrint is We can not touch the NB. Because this is university, much many diverse user loging in.
I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies View RelatedMy access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies View RelatedI keep getting alerts from our WCS stating that our 1252s are drawing low power. Now I am aware that they require enhanced PoE (up to 20W) but as we only have standard PoE in that building we purchased the 1252 series power injectors to go with them.
However, even with the correct power injectors the WCS still reports the draws low power error.
Is this a bug? Running WCS 7.0.172 at the moment.
Forgot to say we are using the PWR-INJ4 and the injector status is enabled and you see the injector MAC address when you drill in to the AP status.