Cisco :: 3602i Autonomous Transmit Power Settings
Jan 27, 2013
I upgraded my 3602i survey ap the other day to the public image the other day and I have to say.. I've got it up and going of course, but I have a concern on the transmit power settings. Originally, the only option it gave me was MAX and -4, which I hadn't seen before, interesting.. -4 of what? 20? 17 probably or I though? At any rate, I went into the CLI to set the power manually, no issues there, though my options are not what I expected, maxing out at 25mw basically, which is fine but.. in setting it manually in CLI, the web interface reports an Error on transmit power. So.. does this work or not? Any survey with this image to verify it's power settings? 15.2(23c)
View 3 Replies
ADVERTISEMENT
Mar 25, 2013
I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
View 5 Replies
View Related
Dec 15, 2011
With firmware 2.06 my DIR-600 had transmit power choices 100%, 50%, 25% and 12,5%.(even 12,5% gave me excellent strength on all my devices, what is really the difference)But after updating to firmware 2.11 (via 2.10, othervise my DIR-600 refused to use 2.11)the choices for transmit power is now only "High", "Medium" and "Low". know the percentage values for those three settings?
View 2 Replies
View Related
Jun 10, 2012
I will be doing a site survey using the client's Cisco 1262 with only 1 radio (g/n), 3 antennas. What is the maximum transmit power, 20dBm or 23dBm? I need to set the transmit power in the Airmagnet to 50% or 3dBm down as recommended by Cisco.
View 4 Replies
View Related
Jun 2, 2013
I am using 10Gig link to connect distribution and access switches. Since we are terminating the cables at multiple locations, we are also doing the link budgeting. The CISCO SFP 10G-LR module data sheet shows two values for the transmit power one of which is maximum power .5dBm and another is minimum power -8.2 dBm. Which value should I choose for the link budgeting.
View 1 Replies
View Related
Dec 14, 2011
What dbm or mw each of the power local settings are? I see on a 1042 from -1 thru 20 and am assuming 20dBm is 100mW.
OM-ess-lab-WLAN1(config-if)#power local ?
<-1 - 20> One of : -1 2 5 8 11 14 17 20 maximum Set power to allowed maximum
View 6 Replies
View Related
Oct 14, 2012
I am looking for the Maximum Power Settings Spec for the 3600 AP. The one from 2008 is too old. Does an update exist? The AP Spec itself does not show power levels by channel and regulatory domain which is what I need. If I can't get the spec, I will have to query the AP using "show ap config 802.11x apname" for each config I need.
View 1 Replies
View Related
Jan 27, 2011
What do the broadcom power saving mode settings mean? If power saving mode is enabled, what is the time it takes to go into power saving mode? What does fast mean?
View 1 Replies
View Related
Mar 17, 2013
We hav ea 5508 pair running in HA mode. Initially the conrollers were running the 73..101.0 code. We were having issues where the primary controller would software reset (according to show sysinfo), the secondary (HA SKU) would take over and then after a few hours the secondary would also software reset and the primary would take over. Also I notice that after this happens that the Tx Power Control doesn't seem to adjust the A radio settings, most of the radios are at the 6 level. Normally they are 1, 2, or 3. Last week I upgraded to 7.3.112.0, later that day the same thing happened.
View 1 Replies
View Related
Dec 19, 2010
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)However ...when powering off (and back on) the device , my Dreambox Sattelite units (DM500) could not get access to the internet anymore (outbound) on port 12000.All other internet traffic went fine ...through browser, wireless, ...all Ok.....I tried everything to resolve but ultimately only succeeded in re-configuring from sracth. powered off the device and brought it back up ....same symptons.Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all Ok again .....until I powered the device off and back on .....I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dreambox unit directly to the device) and ....same symptons ....when powering off/on, the dreambox cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works Ok ). ? It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ?
View 5 Replies
View Related
Dec 4, 2011
Our DIR-615 has started freezing and when reset (power cycled), it reverts to factory settings.This has been running 24/7 for several months with no problem. Three days in a row now I've woken up to find our home network is down and the DIR-615 status lights are "yellow". Power cycling the DIR615 resolves the problem however the DIR-615 looses its settings, reverting to factory defaults (looses the admin password, wireless settings, etc). I can reload the settings from a file saved on my computer but needless to say, this is a bit annoying. I don't believe there are any wireless clients connected at the time as most of the wireless is served by an airport two floors up. There are several wired devices always connected:
a Zoom ATA carrying our "land line"
a tivo (doing whatever tivo boxes do)
a SSL based Voip phone (different than the zoom ata)
an AirPort Express 802.11n (bridge mode) which may have a couple of wireless clients
a laptop which may or may not be sleeping at the time
There are a couple of ethernet switches in the network.Some of the devices acquire addresses via DHCP, others are assigned fixed addresses outside the range of the DHCP addresses served by the DIR-615.Nothing has changed on the network in months.
The only settings I've messed with on the DIR-615 are:
a) set the admin/user passwords
b) Set the wireless network name, enable WPA, set the WPA Key
c) enabled ntp (this is now disabled and I've set the time manually)
d) Change the network base from 192.168.0. to 192.168.4.
The DIR-615 is hardware rev E3, Firmware 5.10 The cable modem (from RCN) is a Scientific American model DPC2100R2
View 12 Replies
View Related
Aug 25, 2011
I recently bought the WAG320N and initial setup (Wizard) went fine ....(I selected all the defaults as presented to me so I did not afterwards modify anything on the settings)
However ...when powering off (and back on) the device , my Dream box Satellite units (DM500) could not get access to the internet anymore (outbound) on port 12000.
All other internet traffic went fine ...through browser, wireless, ...all OK.....I tried everything to resolve but ultimately only succeeded in re-configuring from scratch. This solved the issue .....until ....right...I powered off the device and brought it back up ....same symptoms. Did a hard-reset (back to factory defaults), reconfigured through wizard and ...all OK again .....until I powered the device off and back on .....
I have come to a point now where I excluded all possible 'surrounding' disturbing factors (eliminated switches etc ....and only connected 1 Dream box unit directly to the device) and ....same symptoms ....when powering off/on, the dream box cannot get out anymore and re-configuring from sracth resolves ....until the next power off/on.
And ...it is really the power off/on handling (reboot procedure WAG320N ?) that is causing it .....(I disconnected the DSL line and put it back in , forcing the modem to reconnect DSL and then all still works OK ). It seems as if certain -internal- settings get lost after a power shutdown.....but why specifically port 12000 ? (and ...no...I did not setup any port forwarding not triggering.
View 7 Replies
View Related
Apr 28, 2012
Everything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
View 3 Replies
View Related
Oct 22, 2012
I upgraded WCS to 7.0.22 and the WLC to 7.1.91.0 so that I could add four 3602i's. Funny thing is that they all work fine except that none of their LED's are 'lit' up. They look dead.
Is it the version of sofware?
View 6 Replies
View Related
Oct 7, 2012
On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies
View Related
Feb 18, 2013
I have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows "Hardware beamforming stats not supported (radioid 0x3B00)" message instead of show the client information. I am using a 2504 Wireless LAN Controller running 7.3.101.0 software version, why is not working properly?
View 7 Replies
View Related
Dec 18, 2012
I need implementation of the AirCap 3602i wireless access points. Is there a way to manually configure a AirCap 3602i to function without a WAN controller?, I have an older 4402 WAN controller that will upgrade to 7.0.235 firmware, since the AIrCap 3602i requires 7.2.X firmware, is there a workaround for this.
View 23 Replies
View Related
Mar 6, 2012
I can not get our 3602i AP's to register with our 5508 controller which is running 7.2.103.0 code. We keep seeing an error in the log on the WLC "AAA Authentication Failure for UserName:c46413c08e92 User Type: WLAN USER" and on the Access Point we are seeing [code]
I entered the CAPWAP ap controller ip address directly into the AP so it shouldn't be an option 43 DHCP issue
View 15 Replies
View Related
Jun 13, 2013
I am performing a new install of a WLC 5760 and 3602i APs. I have limited experience in setting up WLCs. I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides: url...
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did). I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC. I have highlighted lines that I think are relevant. I have attempted to find the answer on my own by searching the Internet for these phrases. [code]
View 1 Replies
View Related
Feb 27, 2013
I've been configuring hundreds of 3602i APs via Prime without incident, but I've encountered 2 APs that get to the ap: prompt and doesn't proceed further. If I type boot, then they'll complete the boot process.
How do I configure these 2 APs so they will automatically boot fully?
View 2 Replies
View Related
May 13, 2012
I have a couple 3600s that don't want to join. One i and one e that are both doing the something. It is able to find the controller via layer 3 discovery but it is acting like it is a mesh AP when it tries to join the controller.
From the 2500 controller (running 7.2)
*spamApTask2: May 13 12:03:05.272: f0:f7:55:ae:xx:xx Mesh AP username f0f755aexx xx.
*spamApTask2: May 13 12:03:10.739: f0:f7:55:ae:xx:xx spamProcessJoinRequest : RA
P, Check MAC filter
From the 3602i
flash:/mesh_start_cfg.txt: No such file or directory. The filesystem containing the variables may not be initialized yet.
I should note that 3500 APs are able to join this controller. The field guy is going to try to add the MAC address to the filter list when he gets back out on site to see if it allows it to join.
View 3 Replies
View Related
Apr 8, 2012
Cisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies
View Related
Aug 22, 2012
I have a 3602i access point and have been looking to see if it was possible to load a Mesh AP image on the AP?
View 4 Replies
View Related
Apr 25, 2012
We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.
View 6 Replies
View Related
Jul 16, 2012
Wireless client connected to a 3602i AP running on 2500 series WLC with a latest 7.2 code. Client will now connect to AT&T vpn client - success.Client will connect to SAP application using netweaver gui - failed.With the same scenario, except for the access point being used, client will connect to SAP application using netweaver gui
1242AP IOS/CAPWAP - success
1252 CAPWAP - success
3500 CAPWAP - success
Whats with the 3600 series APs that i cant pass traffic with the SAP application?
Troubleshooting done:
802.11n disabled - still failed
Clean Air disabled - still failed
MFP disabled - still failed
View 4 Replies
View Related
May 16, 2013
Access point gives all junk vlaues in console. I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes
View 2 Replies
View Related
Jan 25, 2013
Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies
View Related
Jan 10, 2011
I've got an ASUS G50V that I normally connect to the net through a wireless router but I recently bought a router so I can make a physical connection and increase speed. However I cant get it to connect to the router no matter what I do (i had it working for a few hours at one point but it dropped off again).I confirmed it wasnt the router but running a crossover cable from the laptop to my desktop, setting static ips on both. Now I can ping the laptop from my desktop but for some reason I cannot ping the desktop from the lappy. I've tried everything I can think of but no dice.
View 4 Replies
View Related
Oct 3, 2012
I recently bought a Nintendo 3DS but unfortunately my University's wireless security (WPA2 Enterprise) is incompatible with the system. As such, I was looking for a way to transmit a wireless signal from my computer, and place an alternative form of security onto it (such as WEP), so that the 3DS can connect to it.
At the moment, my desktop is connected via ethernet cable, which plugs directly into a wall socket. I'm pretty unsure as to what to use, I've heard of things such as 'wireless bridges', but I'm not sure how they work. Also, I'm looking for the device to transmit a signal even if my desktop isn't turned on. Is a router my only option?
View 1 Replies
View Related
Dec 10, 2012
i have ipod but i dont have wireless modem i need software thats work from my pc as wireless modem
View 2 Replies
View Related
May 19, 2011
We have a major poblem going on with our VPN router.We have a 7206vxr router which has an mGRE tunnel forming EIGRP neighbourship with about 800 remote locations using GRE over IPsec.
We have a problem where the EIGRP neighbourship keeps flapping intermittently and this happens to 30-40 locations at one time and very frequently.What I noticed was that the GRE tunnel transmit bandwidth was showing as 8 Mbps. I guess there is an option to change it.Will this 8 Mbps limit cause any issues of EIGRP neighbourship flaps and will increasing the bandwidth useful.
We are also seeing output drops on the tunnel interface.
pcvpnstore#sh int tu0Tunnel0 is up, line protocol is up Hardware is Tunnel Internet address is 10.254.254.254/16 MTU 17912 bytes, BW 30000 Kbit/sec, DLY 50000 usec, reliability 255/255, txload 244/255, rxload 110/255 Encapsulation TUNNEL, loopback not set Keepalive not set Tunnel source x.x.x.x (GigabitEthernet0/2) Tunnel protocol/transport multi-GRE/IP Key 0x328CDF, sequencing disabled Checksumming of packets disabled Tunnel TTL 255 Tunnel transport MTU 1472 bytes Tunnel transmit bandwidth 8000 (kbps) Tunnel receive bandwidth 8000 (kbps) Tunnel protection via IPSec (profile "dmvpn") Last input 00:00:00, output never, output hang never Last clearing of "show interface" counters 00:17:06 Input queue: 0/800/0/0 (size/max/drops/flushes); Total output drops: 732
View 9 Replies
View Related
May 20, 2013
3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
View 7 Replies
View Related
Jan 5, 2012
I have a client(C) and a server(S) nodes plus an intermediate node(I). Each node has a public IP. What I want to do is to transmit some data(whatever) from C to S but this data to go through I. So C ---> S will become C ----> I ----> S. I read something to create a tunnel(ip add tunnel) between C and I and add a route between them ? I tried different examples but did not work at all.
View 2 Replies
View Related
