Cisco Wireless :: 3602i / ClientLink On A FlexConnect AP?
Feb 18, 2013
I have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows "Hardware beamforming stats not supported (radioid 0x3B00)" message instead of show the client information. I am using a 2504 Wireless LAN Controller running 7.3.101.0 software version, why is not working properly?
View 7 Replies
ADVERTISEMENT
Oct 22, 2012
I upgraded WCS to 7.0.22 and the WLC to 7.1.91.0 so that I could add four 3602i's. Funny thing is that they all work fine except that none of their LED's are 'lit' up. They look dead.
Is it the version of sofware?
View 6 Replies
View Related
Oct 7, 2012
On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies
View Related
Jun 13, 2013
I am performing a new install of a WLC 5760 and 3602i APs. I have limited experience in setting up WLCs. I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides: url...
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did). I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC. I have highlighted lines that I think are relevant. I have attempted to find the answer on my own by searching the Internet for these phrases. [code]
View 1 Replies
View Related
Feb 27, 2013
I've been configuring hundreds of 3602i APs via Prime without incident, but I've encountered 2 APs that get to the ap: prompt and doesn't proceed further. If I type boot, then they'll complete the boot process.
How do I configure these 2 APs so they will automatically boot fully?
View 2 Replies
View Related
Apr 8, 2012
Cisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies
View Related
Aug 22, 2012
I have a 3602i access point and have been looking to see if it was possible to load a Mesh AP image on the AP?
View 4 Replies
View Related
Mar 25, 2013
I need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
View 5 Replies
View Related
Apr 4, 2013
A customer have a bad coverage in a corner of his branch office. He like to add a mesh AP (MAP) in the near of that corner.
I checked allready the documention about Mesh but i'm not sure if Flexconnect and Mesh works togheter. This MAP is in a branch office and the WLC is in the head quarter therefore he likes to uses Flexconnect togheter with Mesh.
View 10 Replies
View Related
Apr 25, 2012
We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.
View 6 Replies
View Related
Jul 16, 2012
Wireless client connected to a 3602i AP running on 2500 series WLC with a latest 7.2 code. Client will now connect to AT&T vpn client - success.Client will connect to SAP application using netweaver gui - failed.With the same scenario, except for the access point being used, client will connect to SAP application using netweaver gui
1242AP IOS/CAPWAP - success
1252 CAPWAP - success
3500 CAPWAP - success
Whats with the 3600 series APs that i cant pass traffic with the SAP application?
Troubleshooting done:
802.11n disabled - still failed
Clean Air disabled - still failed
MFP disabled - still failed
View 4 Replies
View Related
May 22, 2013
Does the access point 1600 and 2600 support flexconnect mode?
View 5 Replies
View Related
May 12, 2013
A customer of mine has a centralized 2504 WLC with 7.2 code running. They have 1142N APs deployed locally as well as in remote sites (3) in FlexConnect mode. For no apparent reason last Thursday all the remote APs disassociated with the controller and could not rejoin. All the local APs remained up and unaffected.No changes to the WLAN, LAN, Firewall or MPLS WAN occured to cause this.The customer opened a TAC case and their determination was that ports 5246-5247 were not getting thru. When the customer engaged me this morning I had him run a packet capture on the Sonicwall firewall to prove out if the CAPWAP signals were leaving and returning across the WAN. Sure enough we can see this bi-directional traffic (pic attached). Also, I had the MPLS provider run a trace at the far end and they see the same traffic leave the remote site. And then an odd thing happened; one of the APs at one of the remote sites all of a sudden Joined the controller. So I tried rebooting the AP that is located in the same office, and it fails to Join. When I look on the controller under AP Join statistics, the last activity shows the controller receiving a Discovery Request and response is sent, but no further Config Request and response or Join Request and response.
View 8 Replies
View Related
May 31, 2013
However, I now have a number of devices... certain smartphones so far... that will NOT connect to a FlexConnect AP if it's a 1262AGN AP, but my older 1242G AP will accept the devices without issue. Same SSID, same encryption standards.
If I connect the devices to my guest network (no security), they will connect just fine to both APs, and Non-FlexConnect 1242 and 1262 APs will both accept the devices without issue using my private network.
In other words, it seems to be an issue specific to 1262AGN with my encryption security. My security is WPA2/AES with PSK. No additional security on the SSID.
View 19 Replies
View Related
May 22, 2013
We have a problem when I call bettween two 7925 in same SSID, VLAN voice. They cannot hear each other. The SSID and LAPs are in Flexconnet. From desk phones there are no problem and betwen one deskphone and one wireless phone there no problem too.
View 2 Replies
View Related
Feb 3, 2013
I want to use the flexconnect in the same network where the wlc is located. Normally we will do it for over WAN and branch office. But I want to use in the same main office to avoid more bandwidth utilization on my distribution layer. Wlc is connected on Distribution switch.I want to do local switching in the access layer switch.
The below is the sample topology. But real topology contains nearly 200 AP's(3600 series) and 20 access switches and so on.....So there is a chance of 200 AP * 350 Mbps can flow on the distribution layer.So ,
1)If I use flexconnect any issues will be occuring?
2)Does it cause any impact on VOWLAN?
View 4 Replies
View Related
Nov 29, 2012
I have one WLC 2504 with 7.3.101.0 code and 4 APs 1142 in Flexconnect mode all of them are in one group with 2 SSIDs in two differents VLAN:
-Admin VLAN 151
-Corporate VLAN 158
-Guest VLAN 159
-The auth is 802.1x using an ACS ver 4.2
I connect my Laptop to the corporate SSID and start to have access to web services, intranet services, etc but arround 15 25 min after i connect i lost connectivity to my GW and all the services but i still have my IP info. I do some tests on MAC books, Laptop with Windows XP, 7 and 8 and its the same for all. I config one switch port in the corporate VLAN and i never loose connectivity.
If i reset the WLAN connection all start to works.The ports in the SW are in trunk mode and almost always the APs are in connect mode.
View 8 Replies
View Related
Feb 17, 2013
i have installed ISE1.1 on VM and other hand vWLC7.4 also there in VM i am using 1130AG APs in flexconnect mode and using central auth and central switch.i wan to configure it for CWA(central web Auth) from ISE but a little a bit confuse about ACLs.
View 2 Replies
View Related
May 16, 2013
Access point gives all junk vlaues in console. I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes
View 2 Replies
View Related
Jan 25, 2013
Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies
View Related
Aug 22, 2012
I have about 200 APs (Cisco 1042n and 1142n), 4 controllers (5508 and 2504).. Switches are 2960s and some other stuff.. I Use NCS for management.We have a couple of vlans and SSIDs, when users connect to a SSID i use Flexconnect to associate the users to the correct VLAN.
View 5 Replies
View Related
Apr 8, 2013
I have quick question about wlc software version upgrade : currect version of 5500 WLC : 7.0.220.0,However i am planning to upgrade to version 7.2.110.0,currectly all remote site AP's are connected to this WLC , nearly 150 AP's all are in H-reap mode however once i upgrade to 7.2.110.0 version , all default should come into Flexconnect mode.Do i need to make any configuration or any changes in AP's to get Flexconnect mode or will it be default mode as Flexconnect mode in new version of WLC ?
View 1 Replies
View Related
May 1, 2013
1) Virtual controller 7.3.112 is OK
2) N° 2 LAP 1130 e 1240 is Joined to controller OK
3) flexconnect in localswitch is OK
4) flexconnect in central switch IS NOT work.
View 3 Replies
View Related
Apr 22, 2013
Subject: FlexConnect compatibility with Access Point? We have today one Cisco 5508 and those access point on remote sites
o CISCO AIR-LAP-1131AG-E-K9
o CISCO AIR-LAP-1231G-E-K9
o CISCO AIR-LAP-1142N-E-K9
We plan to use redundancy on the controller and implement Flexconnect on the remote site. What we need to know is if I can implement Flexconnect on all actual access point - I think it is possible on 1142N + 1131G but do not know on 1231AG - is it correct or I'm wrong ? We plan to install the latest SW version for 5508 controller.
View 1 Replies
View Related
Jul 23, 2012
I have found some samples on the FlexConnect setup for the controller side. However none of the documents mentioned how the switch port should be configured that goes to the controller and AP.
At this moment I have a Cisco 5508 configured in CAPWAP mode with 20 APs. I would like to use same controller for connecting one of the remote sites with 2 APs in FlexConnect mode. Current the 5508 to switch port is configured as 802.1Q port. All CAPWAP AP ports are configured as "switchport access vlan X" where X=capwap VLAN. Need to know how the switch port should be set for the remote site where flexconnect APs connect.
View 7 Replies
View Related
May 20, 2013
3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
View 7 Replies
View Related
Apr 27, 2013
Configuring HP switches for Flexconnect. I am not sure if or not its doable? Access Points are 2600 and 3600 with 5508 as a controller. Idea is to keep the branch traffic local but the switches are HP.
View 3 Replies
View Related
Jun 13, 2013
The wlc config guide of Release 7.4 states that sticky key caching (usefull with apple devices) is supported at AP in local mode. [URL]I am testing the new WLC 8500 with 7.4.100.60.
AP mode = FlexConnect
The wlan i activated skc is centrally switched.I debugged the iPhone (4S) roaming.I think skc works at centrally switched vlan on flexconnect APs.
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Reassociation received from mobile on BSSID 00:16:9c:ba:a9:b6
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Global 200 Clients are allowed to AP radio
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Max Client Trap Threshold: 0 cur: 23
*apfMsConnTask_1: Jun 14 14:15:17.069: 30:39:26:2c:d3:ee Rf profile 600 Clients are allowed to AP wlan
[code]....
View 4 Replies
View Related
Feb 20, 2013
after upgrading to 7.4.100.0 im getting this error message when trying to apply changes on the wlan id."mDNS profiling cannot be enabled with flexconnect local switching"if unselect mDNS snooping under (wlan id/advanced) i can apply the changes, but only temporary.when im looking the next time, the tick box mDNS snooping is enabled again.is this a bug or what?
View 7 Replies
View Related
Apr 4, 2013
I have several 2602 AP's that I want to operate in FlexConnect mode. The WLC is at a central HQ and the Ap's are remote. There are central radius servers at the HQ for the wlans. At the remote lcoation, there is a local radius server we want to use for the primary radius server for these AP's. This radius server has been added to the WLC. I have setup a FlexConnect Group, designated the the primary and secondary servers, and then added the AP's to the group. It does not look like radius requests are being sent to the local controller.
For this to work, do we have to check the box under the wlan for FlexConnect Local Auth? Currently, we only have FlexConnect local switching selected.
View 8 Replies
View Related
Nov 29, 2012
I need to integrate Cisco ISE and WLC5508 with FlexConnect (local switching) using EAP-TLS security for wireless clients across multiple floors (dynamic VLAN assignments based on floor level). The AP model used is 3602.
- What RADIUS Attribute can be used for dynamic VLAN assignments based on floor level? Is there an option where I can group all LWAPs in same floor for getting certain VLAN from ISE?
- I intend to use WLC software version 7.2 since 7.3 is latest version. Has someone use WLC software version 7.3 without any major bugs/issues pertaining to FlexConnect and EAP-TLS?
- I read some documents saying L3 roaminig is where the associated WLC has changed. However if user move to different subnet but still associated to the same WLC, would this be consider as L3 roaming too?
View 3 Replies
View Related
Oct 25, 2012
when I did connect the AP to the switch and this is already connected to the WLAN 2500, I got this error message [code] And this AP is not joined to the WLAN 2500, but if I use one model of AP like LAP1120 it works, that mean, the wireless is able to see the Ip Address.How can I do to correct the problem with the AP 3600 series?
View 5 Replies
View Related
Dec 18, 2012
I need implementation of the AirCap 3602i wireless access points. Is there a way to manually configure a AirCap 3602i to function without a WAN controller?, I have an older 4402 WAN controller that will upgrade to 7.0.235 firmware, since the AIrCap 3602i requires 7.2.X firmware, is there a workaround for this.
View 23 Replies
View Related
