I've been configuring hundreds of 3602i APs via Prime without incident, but I've encountered 2 APs that get to the ap: prompt and doesn't proceed further. If I type boot, then they'll complete the boot process.
How do I configure these 2 APs so they will automatically boot fully?
I have a problem on a 1131ag Access point on recycle it stops and makes me maunually type BOOT at the ap: prompt
----------VVVVVVVVVVVVV----------------
ap: Xmodem file system is available.
flashfs[0]: 282 files, 13 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....
I have already performed the ap: set BOOT etc commands a dozen times with the same results. It says: The system is not configured to boot automatically.
I've been trying to get this one going for 4 months now..it was knocked out during a power outage while upgrading it.
I upgraded WCS to 7.0.22 and the WLC to 7.1.91.0 so that I could add four 3602i's. Funny thing is that they all work fine except that none of their LED's are 'lit' up. They look dead.
Is it the version of sofware?
On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies View RelatedI have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows "Hardware beamforming stats not supported (radioid 0x3B00)" message instead of show the client information. I am using a 2504 Wireless LAN Controller running 7.3.101.0 software version, why is not working properly?
View 7 Replies View RelatedI am performing a new install of a WLC 5760 and 3602i APs. I have limited experience in setting up WLCs. I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides: url...
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did). I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC. I have highlighted lines that I think are relevant. I have attempted to find the answer on my own by searching the Internet for these phrases. [code]
Cisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies View RelatedI have a 3602i access point and have been looking to see if it was possible to load a Mesh AP image on the AP?
View 4 Replies View RelatedI need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.
Wireless client connected to a 3602i AP running on 2500 series WLC with a latest 7.2 code. Client will now connect to AT&T vpn client - success.Client will connect to SAP application using netweaver gui - failed.With the same scenario, except for the access point being used, client will connect to SAP application using netweaver gui
1242AP IOS/CAPWAP - success
1252 CAPWAP - success
3500 CAPWAP - success
Whats with the 3600 series APs that i cant pass traffic with the SAP application?
Troubleshooting done:
802.11n disabled - still failed
Clean Air disabled - still failed
MFP disabled - still failed
Access point gives all junk vlaues in console. I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes
View 2 Replies View RelatedInstalled a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies View Related3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
when I did connect the AP to the switch and this is already connected to the WLAN 2500, I got this error message [code] And this AP is not joined to the WLAN 2500, but if I use one model of AP like LAP1120 it works, that mean, the wireless is able to see the Ip Address.How can I do to correct the problem with the AP 3600 series?
View 5 Replies View RelatedI need implementation of the AirCap 3602i wireless access points. Is there a way to manually configure a AirCap 3602i to function without a WAN controller?, I have an older 4402 WAN controller that will upgrade to 7.0.235 firmware, since the AIrCap 3602i requires 7.2.X firmware, is there a workaround for this.
View 23 Replies View RelatedI can not get our 3602i AP's to register with our 5508 controller which is running 7.2.103.0 code. We keep seeing an error in the log on the WLC "AAA Authentication Failure for UserName:c46413c08e92 User Type: WLAN USER" and on the Access Point we are seeing [code]
I entered the CAPWAP ap controller ip address directly into the AP so it shouldn't be an option 43 DHCP issue
I have a couple 3600s that don't want to join. One i and one e that are both doing the something. It is able to find the controller via layer 3 discovery but it is acting like it is a mesh AP when it tries to join the controller.
From the 2500 controller (running 7.2)
*spamApTask2: May 13 12:03:05.272: f0:f7:55:ae:xx:xx Mesh AP username f0f755aexx xx.
*spamApTask2: May 13 12:03:10.739: f0:f7:55:ae:xx:xx spamProcessJoinRequest : RA
P, Check MAC filter
From the 3602i
flash:/mesh_start_cfg.txt: No such file or directory. The filesystem containing the variables may not be initialized yet.
I should note that 3500 APs are able to join this controller. The field guy is going to try to add the MAC address to the filter list when he gets back out on site to see if it allows it to join.
I upgraded my 3602i survey ap the other day to the public image the other day and I have to say.. I've got it up and going of course, but I have a concern on the transmit power settings. Originally, the only option it gave me was MAX and -4, which I hadn't seen before, interesting.. -4 of what? 20? 17 probably or I though? At any rate, I went into the CLI to set the power manually, no issues there, though my options are not what I expected, maxing out at 25mw basically, which is fine but.. in setting it manually in CLI, the web interface reports an Error on transmit power. So.. does this work or not? Any survey with this image to verify it's power settings? 15.2(23c)
View 3 Replies View RelatedI have 2 wireless dvd players. In the past they automatically connected to the network on startup.I was making adjustments on the netgear wndr3700 router while experimenting with some cameras.Now I need to use the WPS option on the dvd player and then run to the router and push the WPS button.hen it connects.
View 1 Replies View RelatedEvery time I restart my computer, it unchecks the "connect automatically" box. I have to manually connect to my wifi. I go in and check the box agian just to have it uncheck next time I boot up. My wife has the same laptop that I do and hers doesn't do this. I'm guessing it must be a setting somewhere?
View 2 Replies View RelatedI recently went through removing some trojan files and malware on my computer with Kevin over in the Virus and Malware Removal section and my computer but the one thing that is not the same now is my wireless internet connection. I have a Netgear wireless adapter. Before I was using the Netgear utility to connect and now that's not even opening at startup just using the Windows Internet Connection utility, which is fine with me but it just won't connect automatically at startup. I have to go manually hit connect and enter my key for it to connect.
[URL]
I am testing our new wireless network using 1 Cisco 2504 wireless controller with 5 licenses 4 Cisco Air LAP 1142N Access Point I configured it very simple for testing There is only one interface and vlan is untaggetd There is also only one WLAN with one SSID Currently security setting is WPA + WPA2 + PSK (I also tested with no security setup) Wlan session time is diabled and controller user idle timeout is set to 1000000 (Max)AP boot version is 12.4.23.3 and ISO version is 12.4(23c)JA3 Problem is clinet(iphone) does not automatically associate with 1142N Access Point even after it learned network. Phone has to be authenticated again to connect to network same iphone can automatically associate with old 1220 Access point but not with New AP if I urn off and turn back on wifi from iphone, it does see the network but does not connect but I have to manually reconnect to it with password I want iphone to connect known network without reauthentication process after iphone's wifi function is turn on?
View 24 Replies View RelatedI have a WCS, four 5508 controllers, Cisco 3750X switches, and both autonomous Cisco 1200, and LightWeight 3502i in service.The problems I am having, is that some of my Access Point reset for no apparent reason, and I get alerted by my NMS.When I look at the switch port, that connects an access point that reported down, I see the POE switch port went down and back up in 4 seconds, just long enough for the access point to reset.There are no errors on the switch port(s). No cable or speed/duplex issues. Switch IOS: c3750e-universalk9-mz.122-55.se1
There are no other pertinent entries in the switch log. Just that the port went down and then back up. Always in 4 seconds.When a reset happens the WCS reports on the access point: '802.11/b/g/n' interface of AP associated to controller 172.20.0.x is down. Reason: Indicates that while the radio state should be updated on controller, no reset should be reported.But nothing else, except that the radio came back up.
This is happening two or three times a day, and rotates. It seems that it never happens at the same time of the day, or the same access point, or the same switch. (I have over 1000 access points and 500 switches in service)I am curious if the WCS is automatically resetting the access point radios, which is causing the switch port to go down/up?And if so, is it possible to turn off the automatic reset?
We have 2 Cisco 5508 WLCs, each wtih 50 licenses. What I would like to do is split the 50 odd APs between the 2 controllers load balancing the traffic. If a controller goes down or there is a break in the path all APs would failover to their configured secondary controller. So far so good.
However there seems to be no way to 'replicate' the configurations between controllers unless I setup HA , but as I understand it HA is Active /Passive, so essentially, unless you get a failover situaltion, completely 'redundant'.
Is there a way or either replicating between controllers automatically with out HA, or is there a way of making HA Active / Active?
I have a few questions about the Cisco WAP2000 we setup for our customers that I have experienced as of late.
1. The AP is prone to reset automatically; what causes the access point to do this and how can this be prevented?
2. The AP has the SSID and the encryption reset back to factory defaults, however the IP address does not get reset. What would cause this?
3. Is it possible to use 2 of the Cisco WAP2000 as a repeater to increase signal strength of another Cisco WAP2000 that has interference from another stronger signal?
I used to have ATT DSL but we recently switched to U-Verse. I have a Trendnet TEW-452BRP 54g wireless router than was handling the PPPoE function. It was set to work flawlessly with my wireless cards. No dropped connections, speed or security issues. It always connected quickly from wake up and on start up. Now we have a 2Wire i38HG wireless router/gateway and it's been difficult to properly set my network up as before. I use the Trendnet behind the 2Wire as my wireless router. Took me a while to figure out what to do, but DHCP is disabled on Trendnet so 2Wire does what it needs to. This option works fine for me. The only problem is that at first my wireless card would not automatically connect to the network through the Trendnet when it is in range like I had it set to do previously. When I would force it to, after 3 times it would magically connect on it's own. I made some changes in the Trendnet (Mainly disabling dynamic DNS and NAT) and that seems to have made a difference. To be honest, I don't know if that is significant or not or if it actually made a longterm difference but it seems like it has. So my problem is now that when I put my laptop to sleep and have it wake up, it does not automatically reconnect. It takes about 2 minutes then it does on its own. I read the event viewer and this is the info it gave me - Your computer was not able to renew its address from the network (from the DHCP Server) for the Network Card with network address 0x0018DE0682D8. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server.
Level - Warning
OpCode - IpLeaseRenewalFailed
Source - Dhcp-Client
Then after 2 minutes -
Your computer was not assigned an address from the network (by the DHCP Server) for the Network Card with network address 0x0018DE0682D8. The following error occurred: 0x79. Your computer will continue to try and obtain an address on its own from the network address (DHCP) server.
Level - Error
OpCode - IpAddressNotAssigned
Source - Dhcp-Client
After this, it connects by itself. I don't believe I have configured the 2Wire or Trendnet properly, so I need some guidance and suggestions on this matter.
Laptop - Intel Core Duo 1.66ghz, 2gb Ram, Win7 Professional with SP1, Intel PRO Wireless 3945ABG
2Wire - 192.168.1.254
Trendnet - 192.168.1.1
- I did not change the IP of the Trendnet and I am not sure if I have to.
From the 2wire - Private Network
Router/Gateway Address192.168.1.254
Subnet Mask255.255.255.0
Private Network DHCP Info
Range192.168.1.64 � 192.168.1.253
[code]....
I want to change router channels to avoid some interference. But do wireless adapters automatically identify the new channel or do I need to change those too?
View 3 Replies View RelatedI've been having a problem with my wireless network connection. Whenever I try and hit the Repair function,it will get stuck on Renewing your IP address for a moment, then change to: Windows could not finishing repairing the problem because the following action cannot be completed: Connecting to the wireless network. I have internet connection on this same computer.Another point to make is that when I click Repair and navigate to the Network Connections window, then hit F5 ( refresh the window ), the wireless connection will quickly refresh and connect normally without error.I won't have to open the Network Connections page and hit F5 anytime I need to repair the connection? Also, as of right now, it's still "Acquiring network address" even though I'm connecting and typing this message.
View 10 Replies View RelatedDoes a RESET automatically re-enable wireless = ON? or is wireless OFF until you go into the config and reenable it?
View 2 Replies View RelatedI have wlc AIR-CT2504-K9. After save config and power down, wlc cannot start. In console I see:
WLCNG Boot Loader Version 1.0.16 (Built on Feb 28 2011 at 13:14:54 by cisco)
Board Revision 0.0 (SN: PSZ163201YR, Type: AIR-CT2504-K9) (P)
Verifying boot loader integrity... OK.
OCTEON CN5230C-SCP pass 2.0, Core clock: 750 MHz, DDR clock: 330 MHz (660 Mhz da ta rate)
CPU Cores: 4
[Code].....
I have been trying to upgrade my WLC 2106, but it is stuck at rommon/grub mode.The steps are as follows
rommon #5> tftpdnldROMMON Variable Settings: ADDRESS=192.168.100.1 SERVER=192.168.100.10 GATEWAY=192.168.100.10 PORT=Ethernet0/0 VLAN=untagged IMAGE=AIR-WLC2100-K9-6-0-196-0.aes CONFIG=
[Code].....
My AP 1131AG is not light weight mode and not able to boot. I have captured logs from consle port it stuck up after following error:
Xmodem file system is available.
flashfs[0]: 9 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
[Code].....