We are evaluating the 5508 WLC Series controller. When trying to associate the 3602i/e wireless access points we have no success. However the 1131 and 1242 legacy AP's will associate.....LWAP Vs CAWAP ?
We've reloaded the 7.2.130 code and it didn't work.
Installed a new 5508 WLC last week, and finished bringing 68 new 3602i access points online in our College Dorms. We are seeing a lot of "Client De-authenticated" errors "Reason: Unspecified Reason: Code 1. Years ago I asked about error code 1. The reply from Cisco was: "The programers put the code in. It basically means we don't know what the problem is."Got a call from one of the dorms stating that students were getting knocked off the network while going to sites. If a student is wired, network is solid.Walked the dorm in question and was getting full bars of signals at all times, and was able to stream a movie from my Ultraviolet account without any break or slowdown as I moved from access point to access point. So.. my device, an iPad, was fully mobile and did not experience any disconnects.Did observe one student using a MacBook Pro. This student was constantly loosing connection to the access point. Checked the controller for the MAC of the student's computer. I did find deauthentication errors. BUT... this student's error was the computer was receiving an IP address from the DHCP that was already in use. At the computer the error message was a timeout issue.I am just learning the ropes on the 5508. Have used 3 4404s for the past six years.
View 2 Replies View RelatedI have some questions about this AP and it's IOS. I have some AP's 1131 and they have IOS 12.34(3g) JA I'm working with a 4402 WLC I'm going to change this WLC for one 5508 but this WLC has a different version software it has 7.2.103. My questions is I need to do any upgrade to my AP's IOS for join to the new WLC ?
I found a compatibility Matrix, in this document I guess i nedd to do some upgrade: URLs
The WGB can be any autonomous access point that supports the workgroup bridge mode and is running Cisco IOS Release 12.4(3g)JA or later releases (on 32-MB access points) or Cisco IOS Release 12.3(8)JEB or later releases (on 16-MB access points). These access points include the AP1120, AP1121, AP1130, AP1231, AP1240, and AP1310. Cisco IOS releases prior to 12.4(3g)JA and 12.3(8)JEB are not supported.
I have 10 Access-Point model 1131 AG are new AP.
When I connect the access-Point to the network, the AP associate only one time but i go to wireless for see the AP, i can see downloading of IOS, but the ios is 3.0.59, the ap don not nothing. I can not change any parameters.
I can not get our 3602i AP's to register with our 5508 controller which is running 7.2.103.0 code. We keep seeing an error in the log on the WLC "AAA Authentication Failure for UserName:c46413c08e92 User Type: WLAN USER" and on the Access Point we are seeing [code]
I entered the CAPWAP ap controller ip address directly into the AP so it shouldn't be an option 43 DHCP issue
I moved 1242 access point to my new buliding which i have 5508 wlc and 3500 acess point are working. i connected 1242 ap in network it got registered and download new ios and downlaoded the configuration and working fine. But i open the WLC tha 1242 ap are not visible in ap list.
View 3 Replies View RelatedI have had a (small) wireless network running in my house for several years but increasingly have the problem that one desktop which connects via a Linksys WUSB54G v4 wireless adapter will connect (associate) with the router but have no internet access. I have another desktop and 2 laptops that will all be connected with internet when the desktop with the Linksys adapter has no internet. The desktop in question is running Windows XP service pack 3. I read several Knowledgebase articles. One led me to run IPCONFIG/ALL where I can see the Autoconfiguration Enabled is set to Yes but the IP address is all 0's, while the DHCP and DNS Servers show 192.168.1.1. Another article suggested updating driver's, but it appears that the drivers have not been updated since 2005.
View 1 Replies View RelatedI upgraded WCS to 7.0.22 and the WLC to 7.1.91.0 so that I could add four 3602i's. Funny thing is that they all work fine except that none of their LED's are 'lit' up. They look dead.
Is it the version of sofware?
On our conference floor, AP 1242AG already exist but I am going to add AP 3602i to increase wireless coverage. . Any issue or concern with this type of setting?
View 23 Replies View RelatedI have a problem configuring ClientLink on a FlexConnect local switching AP (3602i), the problem is that I can not see the clients that are using the ClientLink feature when entering the show interface dot11radio 1 lbf rbf command, the AP shows "Hardware beamforming stats not supported (radioid 0x3B00)" message instead of show the client information. I am using a 2504 Wireless LAN Controller running 7.3.101.0 software version, why is not working properly?
View 7 Replies View RelatedI am performing a new install of a WLC 5760 and 3602i APs. I have limited experience in setting up WLCs. I am hitting a brick wall in getting the AP to join my WLC. My primary document has been this deployment guide:url...I have also sifted through many of the relevant portions of these guides: url...
I went through the setup wizard and followed the instructions in Ch. 2 to the letter (or at least I think I did). I have DHCP options 43 and 60 configured per the 3600 series Getting Started Guide.I believe my AP discovery process is sound because I see activity when I power on the AP and perform debug capwap ap all from the WLC. I have highlighted lines that I think are relevant. I have attempted to find the answer on my own by searching the Internet for these phrases. [code]
I've been configuring hundreds of 3602i APs via Prime without incident, but I've encountered 2 APs that get to the ap: prompt and doesn't proceed further. If I type boot, then they'll complete the boot process.
How do I configure these 2 APs so they will automatically boot fully?
Cisco Aironet 3602I is stand alone or need a controller ?
View 8 Replies View RelatedI have a 3602i access point and have been looking to see if it was possible to load a Mesh AP image on the AP?
View 4 Replies View RelatedI need to configure a Cisco aironet 3602I-K9 because when I connect by the console I can do anything to change the p reconfiguration, this aironet is new and I want to change to autonomous AP, appear errors like:
Translating "CISCO-CAPWAP-CONTROLLER...domain server ()"
CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination . Not in Bound state. I tried to enter to configuration mode but dont valid the configuration terminal command or set command, why happens that?
Wireless client connected to a 3602i AP running on 2500 series WLC with a latest 7.2 code. Client will now connect to AT&T vpn client - success.Client will connect to SAP application using netweaver gui - failed.With the same scenario, except for the access point being used, client will connect to SAP application using netweaver gui
1242AP IOS/CAPWAP - success
1252 CAPWAP - success
3500 CAPWAP - success
Whats with the 3600 series APs that i cant pass traffic with the SAP application?
Troubleshooting done:
802.11n disabled - still failed
Clean Air disabled - still failed
MFP disabled - still failed
Access point gives all junk vlaues in console. I am getting all outputs while booting up and executing commands. But To say, it is as simple as printing with spelling mistakes
View 2 Replies View RelatedI have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies View Related3602I constantly shows a fast blinking green light, watching the boot up I see the following:
Loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"...uncompress: Unknown mzip segment type: 2
Error loading "flash:/ap3g2-k9w8-mx.152-2.JA/ap3g2-k9w8-xx.152-2.JA"
when I did connect the AP to the switch and this is already connected to the WLAN 2500, I got this error message [code] And this AP is not joined to the WLAN 2500, but if I use one model of AP like LAP1120 it works, that mean, the wireless is able to see the Ip Address.How can I do to correct the problem with the AP 3600 series?
View 5 Replies View RelatedI have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
We're in the process of upgrading our Wireless AP's from autonomus to LWAP. We're doing the upgrades remotely (we have 100's of sites to do, and it's not possible to be there to console on to each one), using a local computer to upgrade them to LWAP's with the Cisco Upgrade Tool.Having some inconsistent bugs pop up though from time to time.The most common one is that it basically buggers up the IP address after applying the recovery firmware image. It's supposed to keep the IP it had according to the IPFile.txt (for example 172.25.25.4), but it does something very weird... it keeps the last two octets (so 25.4 from the e.g) but replaces the first two octets with a 192.168 address. So the final address in this example after the UpgradeTool has done its work, is 192.168.25.4 - which is compeltely wrong.
This causes it to be unable to talk to the WLC (obviously, with bogus IP information it will struggle), and gives us big problems in that it wont ever come up unless someone can console to the AP and fix it. We can usually resolve the issue by munging about on the switch - switching the port it's connected to between access and trunk and doing some shut/noshut cycles seems to do the trick mostly.
I recently had to deploy about 4 cisco 1131 AP's to one of our branch location. When configuring them on the controller, i needed to put them in HREAP mode. As soon as i do that and the AP needs to reboot, it will continue to reboot in a loop and indicate the following:
Unexpected exception to CPUvector 1100, PC = 5A9048
-Traceback= 0x5A9048 0x48A8A0 0x4361FC 0x42E078 0x44880C 0x42A280 0x42AA68 0x18A990
[Code]......
I have WLC 4402 with software IOS 5.2.157.0 and i am planing to upgrade the sofware to the latest one (7.0.235.0)
now my question are :
1 - is that software version will support APs [AIR LAP 1131 AG-E-K] ?
2- on down load page there 2 files :
a) Cisco Unified Wireless Network Controller Boot Software 7.0 for Cisco 4400 Series Wireless LAN Controllers.
b) Cisco Unified Wireless Network Software Release 7.0 for Cisco 4400 Series Wireless LAN Controllers. which file i need to upload on my WLC 4402
I have an AP(1131) that keeps disassociating from the controller. It stays alive for about 10 mins then it doens't work anymore. I tired changing the AP but that didn't make a difference. I also tried changing the port on your 500 POE switch. My last effort to fix it was to put the AP on a 3550 switch with a power injector. Still no luck.
I don't understand why its doing this. I am able to connected to it and surf the internet for about 10 mins. After that It leaves the controller and just cycles through different colors.
I have setup a 1131 with multiple ssid's, they show up, but neither one will connect. i need 2 ssid's, one open and one protected. this is the config i have so far:
[code]....
Trying to get an lightweight AP to register with a controller, never seen this one before where the Discovery request is going out to the controller, the discovery response is coming back, but then nothing. At this point the AP should then send a JOIN request, but it just doesnt.
I am using L3 LWAPP, and have the AP statically configured. its a 1131, connecting to a 5.1.151.0 in a WISM. I have run a wireshark and can see the discovery going out, its response coming back, but then nothing (the debugs below also back this up). I have also jumped on the controller and can see the discovery responces are going out but it says no JOIN's are coming in. I'm aware this is an old version of controller but still..
I've tried many different IOS on the AP, including the one it came with in the box, other previously successful IOS and the IOS that 5.1.151.0 dishes out to its registered AP's, multiple AP hardware resets, controller reboots, tried different controllers. etc... What would cause this? Possibly something in the response? See info below:
AP
LWAPP Static IP Configuration
IP Address 172.18.240.244
IP netmask 255.255.255.192
Default Gateway 172.18.240.193
[Code]....
How to shut off wireless admin access on a 1131 AP? I only want to be able to administer the device via the wired LAN. I need to shut of http, ssh, and telnet.
I haven't been able to find anything in the GUI.
How to know the CLI commands?
I have a static IP given to me by the service provider, and I need to make the Access point as a DHCP server to provide me IPs inside my LAN.I have created a DHCP pool in the AP. But do I have to NAT the public IP onto the private DHCP range ? This setup is possible.
View 12 Replies View Relatedi have a air-lap01131-ag-e-k9 that was originally in lightweight mode and configured with a controller, but i am in the process of wanting to convert to autonomous mode, i am having issues with connectivity to the AP from my laptop.
i have followed numerous guides on this forum, i have successfully
downloaded correct firmware
renamed the firmware to .default
placed this in root of tftp server folder
connected laptop via console to view output
connected laptop via Ethernet to Ethernet port of AP
changed static ip on laptop to 10.0.0.2 set subnet mask to 255.255.255.0, default gateway to 10.0.0.1
held reset button on AP when applying power and waiting for radio light to flash red
AP gets a IP address then of 10.0.0.1
But even though both laptop and AP are in the same subnet, i am unable to ping the AP from my laptop and it doesn't start the tftp process
I have disabled firewall etc, and tried with both crossover and straight through cable, it seems there is something missing at this last stage, i even tried on a second laptop but that would not ping either, am i missing something.
I want to install lightweight IOS into Aironet 1131AG by using Upgrade Tool. However, some error messages appear saying:
1. ACL / Firewall might be blocking the TFTP.
2. Disable the ACL/Firewall setting for TFTP.
I don't set up any ACL because I am trying to install to the Aironet which was just initialized by using mode button. Configuration is just like followings.
Is there any possibility that the configuration block the TFTP communication ? now, ping is reachable and directly, I am connecting AP and PC with upgrade tool . and windows firewall is disable on the PC. But the upgrade tool is error. Why the TFTP communication is failed.
Building configuration...
Current configuration : 1361 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log date time msec service password-encryption!host name ap!no aaa new-mode[ code]...
Cisco Air 1131 AP. Having problems with Apple products. Even tried no security.
View 2 Replies View RelatedI configured DHCP pool on Cisco AP 1131, Laptop users are working fine and obtain IP address from AP 1131 DHCP Server, but IPad user is getting IP problem when he try to connect Cisco AP 1131.when i reboot the AP, IPad user getting IP address from 1131 AP dhcp server and access the network resource for the 2-3 hr after that IPad show "obtaining ip address from .....".
AP Detail-
AIR-AP1131AG-N-K9
c1130-k9w7-tar.124-10b.JA2
12.3(8)JEA