Cisco Wireless :: Do 1042 Autonomous APs Support GRE Tunnels
Jan 24, 2013Do the 1042 Autonomous APs support GRE tunnels?
View 4 Replies
ADVERTISEMENT
Cisco Wireless :: WDS On Aironet 1042 Autonomous AP?
Jul 11, 2012i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console:
%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.
hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test authentication open eap WirelessClients authentication key-management wpa version 2 cckm guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1
[code]....
I've tried the configuration from the Cisco config guide as well but without any luck [URL]
Cisco Wireless :: Capability To Downgrade AP 1042 From CAPWAP To Autonomous?
Jan 6, 2011I would like to confirm if it is possible to downgrade AP 1042 from CAPWAP to autonomous? I want to buy the AP model AIR-LAP1042N-A-K9. But i don't sure if in the future it could support this feature.
View 9 Replies View RelatedCisco Wireless :: 1042 Autonomous AP - BSSID Failed Authentication
Feb 13, 2013I am trying to configure a Cisco 1042 autonomous AP and have ran into some problems. I require 2 broadcasted SSIDs that use WPA v2. When I only have 1 of the SSIDs enabled, I can authenticate with no problems. When I have both SSIDs enabled, I can connect to one of the networks, but not the other. I have verified the PSK multiple times, but the logs still show dot11-7-auth_failed. If I remove the working SSID and make no changes to the SSID for which authentication previously fails, everything works fine. Upon adding the other SSID back, I run into the same authentication issue.
View 3 Replies View RelatedCisco Wireless :: 1042 - Convert Light Weight AP To Autonomous Mode?
Mar 19, 2012I have 1042 Light weight AP and i want to convert it to Autonomous mode . i dont find any particular image for this conversion ..when i try to find autonomous image for 1040 its showing "c1140-k9w7-tar.124-25d.JA1.tar"........can i use this image ?...
View 1 Replies View RelatedCisco Wireless :: Does Aironet Autonomous 2600 Support WDS
Mar 20, 2013Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
I noticed that Aironet Controller-based 2602 does not support WDS. I would like to use 1242AG series but it will be going EOS soon.
Cisco WAN :: How Many GRE Tunnels Can 7200 Router Support
Mar 1, 2011how many GRE tunnels (without IPSEC) can 7206 router supported. I have low bandwidth 2000 links & i want to configure GRE tunnels for them.
View 1 Replies View RelatedCisco VPN :: 1921 Router Q - How Many IPsec Tunnels Will It Support
Nov 8, 2011I need to know how many IPsec VPN tunnels one Cisco1921 can support reliably. Haven't had any luck sifting through documentation on the web.
View 2 Replies View RelatedCisco Wireless :: Can 2 Aironet 1042 Use WDS Without Controller?
Sep 20, 2012Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies View RelatedCisco Wireless :: 1522 MAP Through 1042 RAP Not Working?
Mar 25, 2012I'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
Cisco :: Aironet 1042 Wireless N Not Broadcasting?
Nov 27, 2011I have an Aironet 1042 wireless AP if I create an SSID with no security it shows up as wireless N when I see it on a windows 7 laptop. As soon as I apply any security settings is shows up as G and not N. I just want to be able to authenticate with a Windows 2008 server running NPS - this works fine but I obviously want to connect at N speed and not G.
View 13 Replies View RelatedCisco Wireless :: WLC 2112 With 1042 Mesh APs?
May 16, 2013I have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies View RelatedCisco Wireless :: 2504 WLC / 1042 AP - Client Not Connecting
May 21, 20132504 WLC, 1042 AP's
I have my NPS server setup, Group Policy, Certs (RAS+IAS), DHCP option 43, DNS A record
If I look in the event viewer on NPS, it says
Log Name: Security Source: Microsoft- Windows -Security -Auditing Date: 5/22/2013 12:36:37 PM
Event ID: 6272Task Category: Network Policy Server Level: Information Keywords: Audit Success User: N/A Computer: mfs1.Mitchell. internal Description:Network Policy Server granted access to a user.
[Code] .....
But the laptop won't connect or get an IP.
Cisco Wireless :: Power Local Settings On 1042?
Dec 14, 2011What dbm or mw each of the power local settings are? I see on a 1042 from -1 thru 20 and am assuming 20dBm is 100mW.
OM-ess-lab-WLAN1(config-if)#power local ?
<-1 - 20> One of : -1 2 5 8 11 14 17 20 maximum Set power to allowed maximum
Cisco Wireless :: 1042 - New AP Not Showing In Default Group?
Apr 25, 2013I got a new 1042 AP and connected it to the network. I have a 2504 contrller with 6 AP's already on it. I thought I could just plu in the new AP and it would show up in the AP group. Instead it shows up as a rouge AP. How do i get the new AP to show up in the default group?
View 24 Replies View RelatedCisco Wireless :: Captive Portal On AP 1041 / 1042
Sep 18, 2012There is WLAN with Nortel APs witha captive portal. We are migrating to a Cisco Solution and we have AP 1041 / 1042
How can I configure Captive Portal in the 1041/1042 APs
Cisco Wireless :: 2504 - 1042 AP Registration With Controller
Jul 21, 2012I ordered controller 2504 and will arrive soon. I want to know that after configure the initial setup of 2504 (i.e. AP manager , Management IPs etc) and defining the DHCP for AP. Will the 1042 lightweight AP will register with the controller automatically or i need to manually define the AP (MAC address) on WLC. and also whether the Option 43 and 60 are correctly defined?
Management Interface: 10.10.22.15
AP Manager Int: 10.10.22.16
ip dhcp pool WLAN103
network 10.10.3.0 255.255.255.0
[code]...
Cisco Wireless :: Power Requirements For 1042 Mesh Network
Apr 8, 2012this note is from the 5508 controller config manual, does this apply to 1040 access points in a mesh network?
Note:The recommended power source for MAPs is either a power supply or power injector. PoE is not a recommended power source for MAPs.
Cisco :: Unable To Join Wireless AP 1042 With 2106 Controller?
Nov 29, 2012I am not able to join 1042 wireless AP with 2106 controller, even i mention that controller ip is 192.168.200.5 it try to join with controller on 192.168.200.6 ip address always. following are the error logs i can see on console.
*Nov 30 19:50:20.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:20.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Nov 30 19:50:21.435: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.200.6 peer_port: 5246
*Nov 30 19:50:21.436: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.200.6
*Nov 30 19:50:21.436: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
[code]....
Cisco Wireless :: 1042 LAP With 5508 Series Controller - AP Will Not Associate
Jun 11, 2012I have a 5508 WLC licensed for 100 APs. I have 1 - 1042 LAP connected for testing. I have DHCP configured for the AP, and it gets an address of 192.168.254.100/24 - the controller's management interface is 192.168.254.99/24. I can see that the AP is getting an IP and I can ping it from the controller. However, I simply do not see the AP associating. I enabled capwap debiugging and watched the events, but I didn't see anything crazy that clued me in. What am I doing wrong?
The controller is v6.0.199.4
Every time I have set these up in the past they have been pretty straight forward. I haven't gotten too deep into the config on the WLC becuase I don't want to cause more issues.
Cisco Wireless :: Implement 2504 WLC And 1042 Access Points?
Mar 1, 2013We have purchased Cisco 2504 Wireless Controller (One) and Ciscon 1042 Access Points (Five). At present I am going to use 3 access points only.I have attached a simple diagram of our office network. We have more than 30 VLANs configured in Core Switch, we are planning to give wifi access to only 3 VLANs.
1. VLAN 121 ( IP Segment - 10.52.121.0 /24)
2. VLAN 116 ( IP Segment - 10.52.116.0 /24)
3. VLAN 100 ( IP Segment - 192.168.100.0 /24) (Guest)
I would like to use LDAP or ACS for authentication purpose.
Cisco Wireless :: Access Point Coverage Area 1042
Apr 6, 2012I want buy an Access point which cover 300 Meter coverage Area.
Have any data sheet or link where I can found which AP coverage how many Area, Like 1042 Access Point cover how many Feet Space.
Cisco Wireless :: 1041 / 1042 - Apple Ipad Intermittent Wi-Fi Connectivity?
May 3, 2012We are experiencing problems with Apple Ipads on a large scale network that we install and maintain, the Ipads seem to join the network with no problems (bit slower than laptops etc) but will then disconnect for no apparent reason at random intervals. We have ran laptops on the same AP's and in the same area and no similar probems occurred, we are using IOS Cisco 1041's and 1042's, we have seen one of the Ipads's sitting quite happily on a 1042 2,4ghz radio and then it disconnected and went to the 5ghz radio. We are getting similar disconnects on the single radio 1041.
View 13 Replies View RelatedCisco Wireless :: 2.4 / 5Ghz Load Balancing Utilize On Both 1042 And 1252
Oct 25, 2012In my class room, a lot of new Dell notebook (university purchased) all of those are the same model. Those came with 2.4&5Ghz WLAN NIC.
So, my WLC-based AP in that room which is Cisco 1x1042 & 1x1252 running in light-weight.This make huge congest on 5 Ghz. All of my 41 NB go for 5Hgz. And Zero client on 2.4Ghz radio, 2.4Ghz is not utilized at all.
I have read a lot of those related discussion. But I even can not find one that need to utilized BOTH of band. Most of those discussion talking to band-select which is "this feature only goes in one direction from the 2.4 GHz range to the 5 GHz not visa-versa."
My constrint is We can not touch the NB. Because this is university, much many diverse user loging in.
Cisco Wireless :: Access Point 1042 Series In Light Weight Mode Reloads Itself
Apr 30, 2012My access point 1042 series in light weight mode reloads itselft every time it booting, sometimes it boot succesfully.
View 2 Replies View RelatedCisco :: 1042 / H-REAP With Web Authentication Radius
Oct 12, 2011We use LAP 1042's as our main AP's, and we set those in H-REAP (with Local Switching) in order to let them work properly. This is because our WLC is not located in the AP's local network. This is something that, sadly, cannot change, so this has to stay the way it is now.We also use a freeradius server to authenticate users on our wireless network. In our previous situation, before using Cisco appliances, we would just set our web auth page to a certain URL and make sure that the URL was granted access before authentication. We obviously found out that Cisco implemented this by using a Pre-Auth ACL. As a result we've added the IP adres of that web login page to a ACL and added that ACL to the pre-auth for the WLAN that will use Radius Web Auth. The WLAN also has the Radius servers added to the AAA page, so those are in place.
Now comes the problem though. When I connect to the WLAN that will have to use Radius, and try to open a page it will start trying to load the virtual interface (1.1.1.1) and then it will try to redirect to the web-page that I defined in the External Server. Like I stated, I've added the webpage's IP adres (after resolving it) to the pre-Auth ACL, and when I look at the counters I see that go up every time I try to load a page. Yet the browser on the computer gives me a time-out trying to load the external web-server web auth page.
When I disable Web-Auth all-together, I get internet straight away, so the problem obviously is located in the web-auth settings or ACL settings somewhere, but at this point I just don't know where to look anymore.
Wireless :: Can Wireless Router Support Up To 100 User Including Support Network Printer
Feb 16, 2011can wireless router support up to 100 user including support network printer
View 1 Replies View RelatedCisco Wireless :: GRE Tunnels On 4408 Controllers?
Sep 9, 2012I have been tasked by my boss of finding out and implementing a solution of building GRE tunnels from 2 4408 Wireless controllers system for a guest wireless network. I am but a low CCNA wireless, working on getting motivated for CCNP wireless, but I didn't even know if this was possible and if it was where to begin. I have been reading configuration guides but figure I should ask the wireless experts of the world of Cisco.
View 7 Replies View RelatedCisco Wireless :: Multiple Anchor Tunnels On One 5508 Controller
Jan 2, 2012I'm trying to research the tunnel limits on a 5508 controller if you're terminating controllers to two different SSID's. For example. In my DMZ i have a GUEST SSID for contractors and guests and then I have another SSID used by employees so that tablet and mobile phone users can access the interenet. Because we don't trust any of these devices we have that SSID is termiated just as we do our GUEST SSID.
To reduce the number of anchor controllers I deploy, I wanted to start with one 5508 Controller. (then move up to about 3) This controller would have two SSID's, GUEST & MOBILE. On the Foreign controllers when I setup anchor tunneling I will be anchoring to the same controller however to two different SSID's.
Per the 5508 specs it supports 71 tunnels.
So my question to the group is, will the 5508 see this anchoring as one tunnel each? Or does it support 71 Tunnels per SSID?
Cisco Wireless :: 1262N Autonomous AP Configuration?
Oct 26, 2011We have a couple of autonomous 1262's that I'd like to get configured. I would like to put the Ethernet interface out on our Internet subnet and have the clients get a RFC 1918 address from the radio's. Our little Linksys is setup this way and the clients are PAT'ing off the Ethernet interface when they go to the Internet.
Is this possible with these guys or do I have to put the AP ethernet interface into the same subnet with the DHCP scope? I don't have enough Internet IP's to hand out to every wireless client.
Cisco Wireless :: Loading An Autonomous OS On A 1250
Nov 14, 2012When have downloaded the c1250-k9w7-tar.152-2.JA.tar and attempted to load into a 1250 via tftp the process aborts with the following message. [code]
View 2 Replies View RelatedCisco Wireless :: AP 1200 - MAC Filter And WPA Autonomous AP
Jul 19, 2011I have two wireless networks configured in the AP1200, both SSIDs are configured with WPA.
SSID 01: configured whit WPA
SSID 02: configured whit WPA
I have configured the access-list number 700, and I would like to apply to a single network. Achieving the following:
SSID 01 : WPA + Mac Filter, using the ACL number 700.
SSID 02: WPA
How I can apply the list 700 to the first SSID only ??
Cisco Wireless :: 1242 - Mode To Autonomous
Aug 13, 2006i need to change the IOS in a Ligthwiegth Access point and make it work as an Autonomus AP 1242. I have got the image but im not realy clear about the process. I got to enter the Ligthwiegth Access point true the console port but i dont know how is the upgrading process.
View 6 Replies View Related