Cisco Wireless :: WLC 2112 Aren't Able To Connect To Any Of WLAN / APs Will Disassociate
Mar 21, 2012
We recently purchased a 2112 WLC, running version 6.0.199.4. I have everything running through a single port on the controller, which is connected to a trunk port on our 3750 stack. Our management VLAN is vlan 40, and AP is plugged into another port on the same switch which is an access port in vlan 40. APs appear in the controller ok, receive an IP address, but we aren't able to connect to any of the WLANs and periodically the APs will disassociate with the following messages: [code] I'm not sure if that's related to why we can't connect to the WLANs or not...
Another wrinkle is that if we plug in the AP directly to one of the PoE ports on the controller, it all works perfectly. I'm guessing its something switch-related since the only difference is that we're not going through the switch when it works.
View 27 Replies
ADVERTISEMENT
Jan 18, 2010
I've read some opinions that lowering the RTS threshold can facilitate in some noisy wireless environments. I have found how this can be done on standalone APs but cant seem to implement the change on a WLC 2112. How to do it.
View 3 Replies
View Related
May 14, 2012
So, we've been trying to get our network ipv6 compatible and had to upgrade the IOS on our ASA 5510 to 8.4/Little did we know that upgrade to 8.4 would need me to change all out NATs and Access-lists. We have a 1-1 NAT configuration that I need to keep with a bunch of regular rules to different servers (http, ftp, rdp, etc..)
I've been able to change all of that and was able to test it out successfully in our test environment. But, when I moved this to our prod env, the servers aren't able to connect to the internet. I haven't changed any routes - no changes in IP's - just changing the ASA. [code]
View 9 Replies
View Related
May 22, 2013
I have one cisco wlc 2112 with ios 7.0.230.0 with license to support 12 access points. My access points are nine (9) lap1231ag and one (1) lap1310.I just have one wlan (ssid). My scenario of deployment is in layer 3. I have one interface management and ap manager in the WLC. All my Access Points have differents ip address that WLC. I need to configure a unique ssid to associate my six (6) dynamics interfaces (each dymanic interface with different vlan subnet).Each wlan profile (ssid) should have the same security in phase 2 (wpa2/psk). My cisco access points don't support hreap. My wlc support only (4) interface into an interface group, and i need six (6) dynamics interfaces.
View 6 Replies
View Related
May 22, 2013
I have been having an issue with random AP3602I's in HREAP mode disassociating from the 5508 controller. These AP's are in remote offices with 70Mb WAN back to the controller. Randomly one or two AP's disassociate from the controller and I have to bounce the switchport to bring them back online. The WLC is running 7.2. Again this only occurs to one or two AP's not all of the AP's.
View 8 Replies
View Related
Mar 24, 2013
I am running a Linksys Wireless G 2.4 GHz Broadband Router Model WRT54G. I am unable to open any ports. I upgraded to the latest firmware yesterday but still am unable to open any ports. I even turned off my Symantec Internet Security Suite Firewall but still am unable to open any ports.
View 1 Replies
View Related
Sep 25, 2012
I have a 2112 wlc and 6 1142ap's. I noticed that the 2.4ghz channel is filled with lots of networks but the 5.0ghz area is empty. I tried to manually change the channel but it keeps reverting back to 2.4.
View 11 Replies
View Related
Jan 4, 2012
we are trying to configure WLC 2112 with LAP 1042 but getting following erros on LAP1042. It show the Ap is not supported in controller version 6.0.199.4
*Jan 5 16:52:13.397: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.2.101 peer_port: 5246*Jan 5 16:52:13.398: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.2.101*Jan 5 16:52:13.399: %CAPWAP-
[Code]....
View 1 Replies
View Related
Nov 8, 2012
Do we have enable mod eon 2112 WLC ? Also if we need to access WAP from WLC how can we telnet or ssh?
View 5 Replies
View Related
May 10, 2012
My company has a lot of thier business relying on the wireless network and I am trying to reduce the single points of failulre in my network infrastructure. We have a single Cisco 2112 controller with 10 AP's that I am wondering if it's possible to cluster this with another controller for redundancy purposes?
View 3 Replies
View Related
May 16, 2013
I have a Mesh architecture with 2112 WLC and 1042 APs I want just to know if I can connect one 1310 AP to the ethernet port of a mesh 1042 AP with ethernet bridging enabled.
View 4 Replies
View Related
Jan 2, 2012
I am having a trouble with using iTunes, iPhones and iPads on our Wireless LAN. We have the 2112 WLC and 10 1142N WAPs. If I do a network scan, I can see the Apple TV and see that port 5353 is open, which is Apple's Bonjour service. However, if I try to play music/video in iTunes, or on an iPhone/iPad, I do not see the Airplay icon. If I plug into the LAN, the Airplay icon appears immediately. I have created an allow all rule in the ACL but still no dice.
View 26 Replies
View Related
Mar 11, 2012
I have 8 no. AIR-LAP1131AG-A-K9 and WLC 2112 Wireless LAN Controller,i configured the device and its working at deffent SSIDs but when i am trying to enable same SSID on all LAP it shows "AP on dupplicate SSID found and Layer 2 security found".
View 1 Replies
View Related
Feb 8, 2011
I am having a problem using my Windows IAS radius server to validate management users for my 2112 Wireless Lan Controller.I have defined the radius server and it works ok with the policy for validating wireless clients but not for WLC management users.The Remote access policy seems to be set up correctly as the event viewer on the server shows:-
Event Type: InformationEvent Source: IASEvent Category: NoneEvent ID: 1Date: 09/02/2011Time: 11:06:06User: N/AComputer: UK01DC07Description:User xxxxxx was granted access. Fully-Qualified-User-Name = TRAVEL.OAG.com/Dunstable Admins/xxxxxx NAS-IP-Address = 10.10.45.210 NAS-Identifier = UK03NM01 Client-Friendly-Name = UK03NM01 Client-IP-Address = 10.10.45.210 Calling-Station-Identifier = <not present> NAS-Port-Type = <not present> NAS-Port = <not present> Proxy-Policy-Name = Use Windows authentication for all users Authentication-Provider = Windows Authentication-Server = <undetermined> Policy-Name = UK03NM01 - login Authentication-Type = PAP EAP-Type = <undetermined>
....
But, the WLC log shows:
*Feb 09 11:06:06.612: %EMWEB-1-LOGIN_FAILED: ews_auth.c:2104 Login failed. User:xxxxxx. Service-Type is not present or it doesn't allow READ/WRITE permission..
The WLC just returns the login screen
View 7 Replies
View Related
Dec 16, 2012
We are having a 2112 WLC and LAP1042 access points and facing a client disconnection issue. Also signal strength is varying even when client is at steady position. We have a single SSID structure and clients are connecting through 802.1x authentication with WPA2. Access points are joined in H-REAP mode. We also tried by creating a new SSID with open authentication and even on that SSID signal stregnth is varying and client is getting limited connectivity. Attached are the debugs for a particular client and the show tech support for WLC.
View 5 Replies
View Related
May 20, 2013
I've recently migrated a PIX 525 to ASA 5520, but for some reason (through ASA) the users from OUTSIDE aren't able access services published in DMZ as well as some DMZ servers aren't able to communicate to some OUTSIDE services.
-INSIDE to DMZ is working fine. (through ASA)
-INSIDE to OUTSIDE is working fine. (through ASA)
Below is the configuration from my PIX (where everything works just fine) as well as the one on the ASA (where there is a problem), what could be the cause?In the below case the DMZ hosts from 11.1.10.0 aren't able to access SMTP services (through ASA) and the OUTSIDE users aren't able to access DMZ web server (11.1.10.40) through ASA, this all just works fine with PIX.
object-group network inside_subnet_all network-object object inside_subnet_a network-object object inside_subnet_b network-object object inside_subnet_c network-object object inside_subnet_d network-object object inside_subnet_e network-object object inside_subnet_f network-object object inside_subnet_g network-object object inside_subnet_.access-list OUTSIDE extended permit tcp any object host-11.1.10.40 object- group WWW-HTTPS access-list DMZ extended permit object SMTP object dmz_subnet any access-list INSIDE extended permit ip
View 1 Replies
View Related
Jun 10, 2013
I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
View 4 Replies
View Related
Aug 29, 2011
I recent bought an Asus G74SX-A1. While the machine runs like an absolute dream, it does seem to have a networking problem that I have been attempting to address for about a week. In my college dorm there is an ethernet port that carries an active internet connection. When my laptop is plugged into the port via ethernet, I receive no connection (well mostly no connection, every now and then I will connect for a split second allowing me to load my homepage, Google). This problem also exists on my dorm's WiFi. My LAN card is a RealTek BGE Family Controller (PCIe)
However, on my netbook (an Asus 1000HE, which I am typing this post on) everything is fine. I am quick to blame the retailer who sold me the G74SX seeing as they replaced the stock WiFi card with a Bigfoot Killer 1102 card, and my first assumption is that something was not installed properly during my laptop's assembly or that I simply messed up a driver update. I became quite frustrated with the whole situation and in order to find a quick solution I formatted the laptop back to factory defaults.
Something magical happened.For about a day and a half, my LAN card worked. I packed up my gear this weekend and headed back home, and at my parents' house my WiFi card worked wonderfully.I thought my networking woes were behind me, but this was not the case. When I returned to my dorm this afternoon, my LAN and WiFi cards began experiencing the same problems they experienced before the reformat. A third variable of some interest is that I brought my wireless router back to my dorm in order to utilize a less-crowded private WiFi spot and discovered that it worked fine and I was able to connect to the internet on my iPad using my router. This evening, however, my router decided to stop carrying an internet connection as well. I can connect to the router itself, but I cannot receive an internet connection, even on the netbook.
I have tried uninstalling/updating drivers for both the Bigfoot card and the RealTek card to no avail. My best hypothesis is that the problem lies in some setting that both the G74SX and the D-Link DIR-655 have in common, seeing as they are the only wired components that aren't receiving a connection.
Equipment: D-Link DIR-655, Asus G74SX, Asus EeePC 1000HE
View 2 Replies
View Related
Oct 1, 2011
I have some trouble with the setup of an oeap 600 ap. The ap has joined the controller as it should and the remote-lan connection to my corporate network works well, but i can't connect to the corporate wlan.
When i check the event log on the ap it says:
"
*Oct 02 07:36:56.662: (Re)Assoc-Req from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:36:56.665: received assoc-rsp for wireless client, status=0011
*Oct 02 07:37:11.712: DisAssoc-Req/DeAUTH from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:37:11.713: WTP Event: Delete Mobile sent to wlc00:1a:73:d2:82:8c"
and a debug on the controller gives me:
apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Adding mobile
on LWAPP AP ec:c8:82:c2:3a:20(0)
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Association received from mobile on AP ec:c8:82:c2:3a:20
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Sending Assoc Response to station on BSSID ec:c8:82:c2:3a:20 (s
tatus 17) ApVapId 1 Slot 0
[code]....
View 3 Replies
View Related
Feb 10, 2013
I have Cisco 5508 Wlan Controller and its having 6 Fiber Ports and I have AIR-LAP1131AG-E-K9 Access Point. Can this Access Point will work with this Lan Controller? Can i connect 3 switches to this wlan controller?
View 1 Replies
View Related
Sep 16, 2012
So earlier today I purchased a new video card, a PNY Nvidia Gtx 560. After installing the drivers through the disc, I ended up getting he BSOD, and my PC just kept on restarting automatically. I fixed that problem, and found out that I should install the drivers for it through their website instead. So, after restarting my PC yet again, I tried using the Internet (Chrome) and found out that I have no Internet connection. Now, I am writing this on my iPad using the same router and modem that my PC is supposed to be using, but I keep on checking my WLAN adapter and it says that it is Not Connected. Now I have tried every forum, every post, EVERYTHING related to this problem and not a single thing fixes it. Also, when I do the ipconfig, everything says Media Disconnected and that's it. PS, I tried unplugging/plugging back in my modem and router PPS, Is it possible that when installing my new gcard and psu that I may have messed up with something internally?
View 14 Replies
View Related
Dec 23, 2012
I have dell inspiron 640m with Wireless 1390 WLAN Mini-Card and it is connecting perfectly with any other routers. but i can not connect it to CISCO WAP4410N router ! i tried several times but no way.
I can connect IPAD , Samsung Smart tv , Denon network radio and toshiba laptop but not my inspiron laptop. I think my WLAN can not get th WAP4410N IP address !
View 1 Replies
View Related
Dec 19, 2012
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP :
I recently purchased an TL-WDR3600. Setup was easy. Both wlan channels work perfectly. All clients can connect to the internet and access my lan connected NAS. I have some wlan devices which needs to be connected sometimes by http: port 80 and also by telnet or ssh. I can connect from a wlan device to a lan device. But NOT from a wlan to wlan or a lan to wlan. I allready diabled WMM and tried some other wlan settings, like disable one channel, changing the channel width etc.
My setup is : ADSL device -->(192.168.1.X dhcp) WAN TL-WDR3600 --> to LAN&WLAN (192.168.0.X dhcp and some LAN connected with static 0.200, 0.210)
View 6 Replies
View Related
Aug 31, 2009
I can't connect to the internet using wireless. Can access the internet just fine with my cable. All I see is the red x and its not able to detect any networks. I reinstalled drivers, it works fine for a second, and then dies out again.
View 2 Replies
View Related
Dec 16, 2011
My Laptop can't connect to the internet wirelessly. Wireless card can connect torouter but once connected to the It can't acquire an IP address.
View 5 Replies
View Related
May 20, 2012
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies
View Related
Mar 2, 2012
Airlap 1041n i have air lap 1041n(soft version 12) and wlc 2112 i dont have dhcp server perhaps i use tftpd32 to act as a dhcp server.
my problem is
1. i have configured the wlc 2112 and it's ip is :172.25.1.1
2. i cant configure the air lap 1041n. when i enter the cli mode the following message comes ****continuously***:
Could not discover WLC using DHCP IP. Renewing DHCP IP.
*Mar 1 01:44:11.310: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does not have an Ip !!
3. my question is how to stop this continuous mgs ?
4. how can i assign an ip to my AP ?
5. how can i join my AP with MY wlc ?
I have to show my office that i can control two ari lap 1041n-k9 with my WLC 2112 and my laptop's wifi and cellphone's wifi are able to get connected with the Access points.
View 1 Replies
View Related
Jan 4, 2012
I have a client with a 2112 WLC and 1252AG radios. The clients work fine, but an SNMP management server can not reach any of the clients over the wireless. Before the WLC and new AP's were installed, they were running older Cisco Autonomous AP's and had no problems with SNMP. My monitoring system uses SNMP and it can reach the WLC just fine, so there doesnt appear to be any issues on the switched network. What can be blocking the SNMP on the WLC?
View 4 Replies
View Related
Dec 23, 2012
I have dell inspiron 640m with Wireless 1390 WLAN Mini-Card and it is connecting perfectly with any other routers.but i can not connect it to CISCO WAP4410N router ! i tried several times but no way.I can connect IPAD , Samsung Smart tv , Denon network radio and toshiba laptob but not Imy nspiron laptop. think my WLAN can not get th WAP4410N IP address !
View 1 Replies
View Related
May 21, 2011
Remote-access users aren't able to reach our remote network through a site-to-site VPN tunnel between two ASA 5505's.
I've seen several threads about that here, I've run through the walkthrough at [URL] I've taken a stab at setting split tunnelling and nat exemption, but it seems I'm still missing something. Remote-access users can reach the main site, but not the remote site.
Remote-access (vpn-houston) uses 192.168.69.0/24.
The main site (houston) uses 10.0.0.0/24
The remote site (lugoff) uses 10.0.1.0/24
View 5 Replies
View Related
Oct 16, 2011
how to configure the backup port for the management interface for a WLC 2112. I see in the documentation that it states:
"Each interface is mapped to at least one primary port, and some interfaces (management and dynamic) can be mapped to an optional secondary (or backup) port. If the primary port for an interface fails, the interface automatically moves to the backup port. In addition, multiple interfaces can be mapped to a single controller port."
But nowhere can I find where it says how exactly to do it. Google seaches have come up empty as well. I am connecting the WLC to a 3750 stack, and would like to have a secondary port from the WLC connected to the second node of the 3750 stack. So far I have connected port 1 (management) of the WLC to a port on node 1 of the stack which is configured as a trunk and everything is workign fine. I have also connected port 2 from the WLC to a port on node 2 in the stack that is configured the same as the port on node one. how to tell the WLC to use port 2 as the management backup if needed.
[URL]
View 2 Replies
View Related
Feb 23, 2013
I am a owner of a cyber cafe.there is wired lan connection on the desktop computers in my cafe which is connected to a wifi router (Dlink).I have issue while playing counter strike 1.6.if i am connected to wifi router from my laptop, i am not able to detect the lan game server. the game server which is created on one of the desktop machine on the lan network of my cafe ! In other words I want to play cs 1.6 from my laptop which is connected to a LAN network through wifi router !
Laptop Config :
Os : windows 7
Desktops OS : windows xp
Router : Dlink
View 1 Replies
View Related
Jan 13, 2012
I have a Vostro 1500 and cannot connect to a wireless network with a dell 1395 WLAN minicard os XP home, what are possible solutions?
View 1 Replies
View Related
