I am unable to connect and Android device (HTC Desire, Samsung Nexus S etc) wirelessly to the DAP-1522. I've search through the forums and can't find anyone else having issues with Android so I think it must be one of my settings. It works fine if I switch to WEP however I don't want to use the weaker hackable protocol. Any way to have the DAP-1522 in WPA working with an android device?
View 4 RepliesTiVo and Pioneer offer remote control software for iOS and Android equipment. I've been using both for a while, and it's great stuff. When hardwired to the router. Behind the DAP-1522, not so much.The DAP works like a champ in every respect except in this application. Everything attached to it can hit the internet- the TiVo, the Samsung smart TV, my laptop via 1000baseT, and to anything else networked in the house. Presently the iPad can control the Tivo, but not the Pioneer. But Airplay on the iPad connects to the Pioneer with no problem. And then the iPad remote can control the Pioneer again.Another example is that the iPad can't find the TiVo, but my Android phone can. Usually.
View 1 Replies View RelatedI have 4 DAP-1522's bridging to a WNDR3700v2. Any device plugged into any of the 1522's can access the internet and can access shared drives etc. on any other device plugged into any 1522. I can access the WNDR3700 admin website from a device connected to a 1522.
However, no device plugged into a 1522 can access a device plugged into the 3700's ethernet switch. Likewise, the devices plugged into the 3700 cannot access devices plugged into 1522s.
Devices plugged into the 3700's switch can access the internet and can access each other.
I have changed network cables, power cycled all devices (PCs, bridges, routers, etc) at least once. I am running latest firmware on 1522's and 3700. In short, I've tried just about all the basic stuff.
It almost appears that the 3700's switch is acting as an isolated network. I would say that were true, except that I can access the router admin page from anywhere (any 1522 and directly connected to the 3700).
All devices are within the 10.0.0.x address range with a subnet mask of 255.255.255.0. Again, I have no problems accessing the internet. Just the problem of devices plugged into a 1522 communicating with devices plugged into the 3700 and vice versa.
Setup my DCS-930L for DDNS (Dynamic Domain Name Server) so I can access the DCS-930L via the Internet (couldn't access the camera half the the time while on vacation using mydlink) and can now access the camera using my laptop, Android Thrive, and Motorola Droid 3 via the URL I've created but can only see the video when using the laptop.
I have the DCS-930L set to Java but when I log into the camera with the Thrive or Droid 3 (both Android devices) I don't get video. I can make changes to the camera settings and everything else you can do when logged into the camera but just can't see the video. If I change the 'View Mode' in the video setup to 'Image', I will get a picture on all three devices (Thrive, Droid 3, and laptop).What do I need on the Droid 3 & Thrive so I can see the video when I log into the DCS-930L with an Android device?
Region : NewZealand
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
I've plugged in a USB flash drive and enabled shared storage on my TL-WR1043ND router. With "Access shared storage with password" unticked, I can access the share using both my Windows 7 Laptop and Motorola Defy+ (with ES File explorer) and successfully play any Music off of the network share using the Android App, ES File explorer.
If I enable "Access shared storage with password" and attempt to log in using any of the user accounts I've set up on the device, I will be able to access the shares using the credentials on my Windows 7 Machine, but not with my Motorola Defy+, instead I will simply receive "Login failure". I'm Picking it has something to do with the network share type?
Region : Italy
Model : TD-W8960N
Hardware Version : V4
Firmware Version : 67406
ISP :
I have problem on router td-w8960n v4 internet speed download is limited a 4 mb in device android e ios wifi connected for test i use application speedtest.net on ipad 3 and samsung galaxy s
My DIR 655 router quit working and so I called D link. She had me reset the ip to 192.168.5.x. So now my dap1522 is not connecting to the 655. I connected the dap1522 to my laptop via ether-net and typed in dink, and got nothing, then put in default ip for the 1522 and still nothing. I also tried ip scanner and it would not come up.
View 1 Replies View RelatedI just got the motorola droid 3, my first android device. I'm trying to figure out how to get my device to connect to my network as it won't obtain the IP address.I have a Motorola Surfboard SBV5120 Modem and a Microsoft MN-700 router. I just switched from the Palm Pre Plus which connected perfectly to this network, the network is unsecured and has 2 pc's and a 360 running on it. I was able to connect to my friend's wireless network fine at his house.
View 9 Replies View RelatedHow do I fix the problem". Domain not set.invalid may not be the problem. had a power surge at my house and it took down my internet. I had to reset my router back to factory settings and I finally got the router to work with my PC. But I cannot access the internet from my iPad 2 or my Android phone. Both devices see the network and can hook up to the network but the internet is not working on either device.
View 14 Replies View RelatedI'm trying to connect to my wireless network using an android device with certificate but with no success.I'm using a WLC4402 7.0.235.3 SSID Security (WPA2 Auth802.1X + CCKM) [code]
View 7 Replies View RelatedI'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
I have a Cisco ASA 5510 (with an AnyConnect Mobile License enabled) I used to be able to connect to the VPN using the AnyConnect app for Android form the Google App store (the phone is a Samsung Galaxy S II LTE, if that matters). Like I said everything used to work fine until a few weeks ago, the only change I made to the router was giving it a different external IP address (I changed ISP), I'm pretty sure it worked after that. But now when I try to connect with my Android I get this error: "Clientless (browser) SSL VPN access is not allowed".
View 1 Replies View RelatedMy D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies View RelatedI recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies View RelatedMy problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.
I just purchased a DAP-1522. The sticker on the bottom says it's a version B1, with firmware 2.0.In the web interface, it says: "Firmware Version : 1.21 , Fri 26 Jun 2009"I downloaded the 2.01 firmware from the D-Link site and when I try to upload it, it says it's not an image file.
View 11 Replies View RelatedI have bought 1 Dlink Dwl 2100 Access Point about 1 week, it working with ( Default Gateaway 192.168.1.1) but I want connect with 2100Ap But I get Ip from my Livebox Orange.Can I get Ip From 2100Ap (Default Gateway 192.168.0.50), not by LiveBox Orange (Default Gateway 192.168.1.1).My brother live upstair (with LiveBox) I Live ground Floor and connect to Cable Utp cat5 form upstair to ground Floor. In my room I have a Switch connect to 2100Ap.
LiveBox Orange Default gateway is 192.168.1.1
Dlink dwL 2100Ap Default Gateway is 192.168.0.50
My os is windows Xp sp2
I have a DIR-655 router with a DAP-1522 connected in bridge mode. The firmware on the router is 1.21 and the firmware on the bridge is 1.21. I have my SSID set to broadcast on the DIR-655 with WPA-Personal encryption. When I initially setup the DAP-1522, I was able to access the setup page and connect to the DIR-655. On the status page of the DAP-1522, wireless radio is enabled and status is connected. I connected my XBOX 360, Sony BR player and DirecTV DVR to the wireless bridge and none of them can connect to the internet.
I can wirelessly access the bridge's IP, 192.168.0.50, from any computer connected to the DIR-655 but when I attempt to access the internet on any device connected to the DAP-1522, I do not get a connection. On the XBOX 360 I cannot connect my live account. On the Sony BR player, I get a message that new firmware was found, but when it attempts to connect to the internet to download it, the connection times out. Same occurs when attempting to access the internet on the DirecTV DVR receiver.
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
my config : one DAP-1522 as an AP + one DAP-1522 as a switch, 6 meters between them, signal strength about 70. Any others wifi networks around my house. both with FW140b03.bin dated 01/14/2011.Most of the time, both work correctly. But time to time, the wifi link is ko. In AP status, the switch is mentionned connected (uptime = 3 hours ...). The red led is blinking on the switch. The administration web of the switch is not available and the link is ko. Unplug and plug power units doesn't fix the problem. I need to reset DAPs.From Dlink experts, i would like to get more description about issues :
- in switch mode, which are the events modifying the red led state ? what does blinking / off led mean ?
- in AP mode, what does "uptime ...STA ...." mean ? frames are periodically received from STA ?
Will the dap-1522 work with 3d video ie; from a 3d Blue Ray Player? I am upgrading system to an LED Samsung 3D TV and Samsung 3d Blue Ray Player. I know that HDMI 1.4 cables will work but am looking at the wireless option.
View 1 Replies View Relatedi have multiple DCS-930 and DCS-932 at my home. I also have other IP cameras. Is there a way to add IP cameras to the mydlink app on Android, iPad, and web?
View 1 Replies View RelatedMy Android Tablet ASUS TF101 fails to wireless connect at the next reboot after it has been sleeping.Unplugging the DIR615 and replugging solves the problem until next time. The Tablet shows a poor signal until the router reboots (even at 4 feet away). The router firmware is 3.11NA and the hardware is C1.Other hardware like an ACER WIN-7 PC can still wireless connect when this problem is exhibited.
View 6 Replies View RelatedDir 615, hardware version E4, Firmware version 5.1.Intermittent (95% of the time), problem accessing Google using my Android via wireless. A PC using XP on the same network has no problems. Using the Android on my local library's network I have no problems.Have restored to factory default settings and reconfigured with no improvement.
Modem setup: Setup to connect to another router, UPnP disabled, DHCP server disabled, 802.11 mode -mixed 802.11n & 802.11g (Android connects using 802.11n PC uses 802.11g have forced Android to use 802.11g to no avail), Auto channel scan, (have tried fixed), Channel width 20/40, visible mode.Internet connection Dynamic IP of course it is going out through my other Dlink ADSL 2 modem router. Also disabled QOS engine.
changed the router wan access pwd and now trying to test the dap i can't seem to log in with the default ip / dlinkap url access i have tried the bridge and ap switch setting on the dap with no luck after resetting the dap a couple of times with no luck ..
View 8 Replies View RelatedI installed my 1522 today with a Direct TV receiver and made a connection using AP mode.
How do I know what band is being used and how to switch between the bads.
Under Advanced>DHCP Server, when I put in the Default DNS server of 192.168.0.1 and click save, it goes away. Meaning it doesn't show up anymore.
View 4 Replies View RelatedDo the devices connected to the DAP-1522 communicate directly with each other or do they communicate through the router.My DAP-1522 is set up as a bridge connected to my DIR-825. The reason I ask is I've set up an HTPC connected to the DAP-1522 and I also have media devices connected to the DAP and am wondering if they'll communicate with each other directly or if they have do it by going to the router and back. That way I can use my HTPC to serve media to my devices at local speeds.
View 1 Replies View RelatedI already have a DIR-855 and was considering using a DAP-1522 in conjunction to bridge my 5GHz N to my living room to feed HD media to my PVR box and also feed wired-only clients like my TV and BR player. But, in my new flat I find that the walls are pretty thick and my wifi signal is dropping off pretty quick, so I was wondering if you can configure the DAP-1522 to simultaneously be a wifi bridge to feed my media clients, and an AP to feed any laptops that might be in use in the living room?
View 1 Replies View RelatedHad to reset out DIR-655 router. This ended up changing our network password. Unfortunately, my DAP-1522 was not informed of this change and it will not connect to my Directv receiver now. I attempted to log into the bridge to change the password and it will not let me in. I attempted to reset the DAP in hopes that I would just be able to start over from scratch, but no dice (Assuming that I did it correctly)
View 4 Replies View Related