I loose the ability to connect and I was thinking if I could extend the wireless network by adding a DAP-1522.I want to have the WNDR3700 and the DAP-1522 connected via wireless and using a laptop I want to be able to access the wired network from anywhere in the facility.
I've been playing with this setup for over a month with no real success. I'm trying to use the DAP-1522 as a wireless bridge to provide connectivity to my entertainment center which consist of a PS3, Directv DVR and Internet ready TV. I tried the setup as described in the manual, but not getting to the internet. Initially I was able to connect the 1522 as a bridge, but the connection kept dropping, especially anytime I actually used the internet (downloading a VOD movie). While troubleshooting the dropping issue, I changed all the 1522 settings and now it cannot access the internet at all through. The WNDR3700 is routing my home network fine...it is setup on the 192.168.1.x address space. I understand the 1522 came setup for 192.168.0.x, is the 192.168.1.x/192.168.0.x thing jacking things up? I initially had the 1522 setup with the 192.168.1.x IP from my home network and the gateway set to my WNDR3700 (192.168.1.1)...should it be on the 192.168.0.x? I have updated the firmware to 1.31.
View 2 Replies View RelatedI cannot connect through my wireless router (Netgear WNDR3700) WITH MY INSPIRION DUO. I can connect with a verizon MYFI wireless card, and alo through ethernet on Duo. I get "Problem with wireless adapter or access point" The software driver is newest. System ism W7 Home premium
View 1 Replies View RelatedI'm sure it's on here but because I dont understand the name of what I'm looking for, I'm having trouble searching. My main network is setup for wireless via a netgear wndr3700. I'd like to use my old linksys wrt54g v5 to connect to that network wirelessly and allow me to connect my xbox via wired ethernet. Basically instead of buying a wireless adapter for the xbox, i'd like to know if/ how i can use my linksys router instead.
View 13 Replies View RelatedSo I have a Netgear N600 WNDR3700 wireless router setup at home, and it works great for wireless, but when I plug in my desktop with CAT6 Ethernet cable to the router (didn't bother putting a wifi card in my desktop) for some reason it won't connect to the internet. I know the cable works because I've used it in the past, but for some reason I can't get it to work with my Netgear router.
View 7 Replies View RelatedThey brought me a LAP1522 referring that it is not working properly. I am trying to connect to console port but the problem is that I only get log messages but I cannot edit something or type any commands. I have attached the log messages if you can catch something from there. Ignore the messages about not finding controller because the AP has been removed from the real network to my office.
View 14 Replies View RelatedI puchased the N600 WNDR3700v3 Dual Band Gigabit Router. I am able to see my wireless account I set up and is out there to connect to, but I cant connect. I can connect with an ethernet cord, but nothing wireless. It doesnt work for my home or work laptops. Prior to this I had another wireless set up and I am tempted to plug that one back in.
View 1 Replies View RelatedI just bought a WNDR3700 to upgrade my wireless network. I have two primary goals:
1. Get my one HTPC that is connected via wireless bridge (due to its location) out of the 2.4GHz band because of microwave interference; and
2. Move to 802.11n to increase bandwidth to handle additional wireless HTPCs.
Currently, I have my HTPC and Xbox 360 connected to a WRT54GL. The WRT54GL connects to my primary wireless router via bridge mode. I prefer to use a bridge instead of buying separate wireless adapters for the Xbox and HTPC. Any recommendations of wireless routers that I can use as a bridge to connect via 802.11n in the 5GHz range. DD-WRT compatibility is a big plus. Gigabit switched ports also a plus, but not that important.I could just buy another WNDR3700, but I am looking for a less expensive option.
Currently considering:
Linksys E2000
Linksys WRT400N
I have had a Netgear WNDR3700 wireless router for over a year now, and have had no problems connecting to wireless devices (currently connects perfectly to: windows 7, OSX, Android, and Meego). I have recently purchased a Sony Bravia NX720, which has a built in wireless card. When I connect the television via LAN to the router the internet works fine, however when I connect via my wifi network (i.e. there is no physical connection between the tv and the router) I get the following message:
Connection Results
Wireless Device On TV: found
Local Access: OK
[Code].....
I have a Netgear WNDR3700 v2 that I loaded with dd-wrt (v24-sp2 std). The only real problem that I am having is with the wireless. I can't get anything to connect at 300mbps. Even if I set it to n only it still only connects at 54mbps. Right now I am running it with encrytion off to rule out that causing any problems. and yes it would connect at 300mbps with the stock netgear firmware.
View 3 Replies View RelatedAfter a firmware update the DAP-1522 HWversion A will not connect to a Hide SSID.
I am Using the DAP-1522 as a Bridge in 5Gz.
Is it possible to connect the dap-1622 to a hidden network using WPA Radius? I've tried, but didn't succeed. I'm running FW version 1.41. I've tried with older FW versions, and none of them seems to work.
View 1 Replies View RelatedCan't connect DAP-1522 to my Verizon Fios Router
Went through the setup on the DAP-1522. Selected my Verizon FIOS wireless network and entered the WEP key. Everything looks ok on the status page - except Status: Disconnected
Reset/restarted and reconfigured DAP-1522 several times - same result. Can't get it to connect.
I am currently using a DIR-655 for the home wireless network.DSL into a 2-Wire home portal (not wireless) and ethernet into the DIR-655.I need to connect a number of wired devices in a couple of different rooms. Some streaming HDTV content to other devices in other rooms. I'm thinking of the following:
-DIR-655 routing between the DSL subnet to the internet, the 2.4GHz wireless and a couple of wired devices.
-DAP-1522 routing between the 2.4GHz wireless, 5GHz wireless, and a few wired devices.
-DAP-1522 bridging between the 5GHz wireless and a few wired devices.
All devices will/may need internet access.HDTV content would be between wired devices and only over the 5GHz wireless (no HDTV to/from internet).Is the DAP-1522 the right device(s) for this?
Just got my router running and when I connected to it via my laptop, it didn't ask for a password and it says unsecured connection when I put my mouse over it. Where do I go in the settings? I do not see it at all?
View 3 Replies View RelatedI've got an older desktop that needs a dual band upgrade and would like to know if a PCIe adapter w/ external antennas for desktop wireless is better/faster than the USB variety? They cost about the same. The router is a dual band WNDR3700 v1.
I've heard salespeople at retailers say, for desktop, go w/ the USB as they offer better performance than PCIe adapters even w/ external antennas... Does anyone know if the extra noise within the desktop case kills whatever benefits that the extra power and external antennas that a PCIe card has over a USB adapter?
Here is my current setup:
Cable Modem>WNDR3700>CAT5E>WNDR3700
The last WNDR3700 is in my media closet at the other end of the house essentially serving as an AP. I get weak signal in the garage on a standard WiFi card. Thing is I am installing an IP camera soon, so I need ethernet connect ability. Hoping to not have to buy another WNDR3700 as they are pricey. The bottom line goal is to have a router or AP out in the garage to connect my IP camera. What would be the best way to accomplish this? Running a cable is out of the question price wise right now. I have no problem buying a directional antenna and pointing it towards the house, but this would require the router to have external antenna.
I am trying to configure a 3300 Wireless Print Adapter with a NET GEAR WNDR3700 Wireless N Router. During the Configuration if I have no security set up on my network, the 3300 establishes a connection. If I however, turn any form of security on ( WEP, WPA-PSK [TKIP, WPA-PSK [TKIP] + WPA2-PSK [AES] ), the Connection fails. No security is not an option.
This happened while switching routers. The 3300 worked fine on my D-Link Wireless G router (WEP). I was wondering how to resolve it.?
Have a site that has a 1522 installed. I need to add two new outdoor AP's. Would the 1550 work along with the 1522 or would I have to replace it?
View 2 Replies View RelatedAfter a wireless network interruption, one of MAP 1522 it's not joining to WLC .
(Cisco Controller) >show ap join stats detailed 00:08:30:bb:53:20
Discovery phase statistics
- Discovery requests received.............................. 7
- Successful discovery responses sent...................... 5
[Code]....
I got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View RelatedI'm facing the following doubt regarding the AC Power Connector on the 1522 AP.We are powering up the AP through PoE, so the AC Power Connector is not used.BUT,do i have to seal/protect the connector or leave it as is?
View 3 Replies View RelatedI'm trying to mesh a 1522 MAP through a 1042 RAP but this doen´t work. I get strange messages on the trap log:
1 Mon Mar 26 18:40:19 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. .. .
3 Mon Mar 26 18:37:13 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:10'. 4 Mon Mar 26 18:34:00 2012 Mesh node 'f0:25:72:d9:69:6f' has changed its parent 5 times in last one hour.
5 Mon Mar 26 18:34:00 2012 Mesh child node 'f0:25:72:d9:69:6f' has changed its parent to mesh node '58:35:d9:c6:60:10' from mesh node '58:35:d9:c6:60:1f'. 6 Mon Mar 26 18:33:44 2012 Mesh child node 'f0:25:72:d9:69:6f' is no longer associated with mesh node '58:35:d9:c6:60:10'.
[code]....
If i debug the 1042 i also see "... has 1 AES-CCMP TSC replays messages..."I have some 1522 MAP meshing through 1142 working fine on same 5508 controller version, i think there are few differences between 1042 an 1142.
I have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
I have a wireless sytem with a WLC 4400 and several 1522 Access Points. They don't actually function as Access Points because I'm using radio communication only for backhaul. There are no clients connected to the Access Points. All traffic on the network comes from the devices connected on the LANs that are bridged through the APs ethernet port.
I would like to create filters to allow only certain devices to be able to transmit over the radio link. I've used this in the past on 1310 units and it was very easy to do via GUI. This filter could be either by IP or MAC Addresses. IP would be better for me.
Using as AP. Last Tuesday in the middle of a Netflix movie the video stopped. Now the wireless portion of the DAP-1522 refuses to pass any type of video. Everything else works (email, Google, Facebook, etc.). I can get to Netflix, Youtube, Yahoo, etc. .....but none of them will pass video.
Using a direct wired connection to the DAP-1522 everything works. Netflix, Youtube, etc.
Download speed checks at 17.74mbps.
I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View RelatedI have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedSo just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.