Using as AP. Last Tuesday in the middle of a Netflix movie the video stopped. Now the wireless portion of the DAP-1522 refuses to pass any type of video. Everything else works (email, Google, Facebook, etc.). I can get to Netflix, Youtube, Yahoo, etc. .....but none of them will pass video.
Using a direct wired connection to the DAP-1522 everything works. Netflix, Youtube, etc.
Download speed checks at 17.74mbps.
I'd like to use VLC to view the MJPEG stream from the DCS-930L. What URL should I use to do this?
View 9 Replies View RelatedI recently bought 3 DCS-920 to monitor my home while at the office. However I can't seem to get the damned things to stream video using the dyndns service. I linked my router to the dyndns account and host service. I portforward the ports my cameras are assigned. Up to this point its all good, I can access the cameras and their settings pages while outside. However both the Java and ActiveX options for video streaming do not work. Even within the network, using their raw IPs to view the cameras the videos stream works.But putting in the hostname and port they are assigned brings up the camera page, but no video.I can only assume the ports the video and audio run on are seperate, as when I put one camera's IP in the DMZ host on my router, it works with the DNS. Unforunately I can only do that with 1, and I'd rather not do that at all.
View 6 Replies View RelatedWhen accessing the camera on mydlink, or on a browser using http://x.x.x.x/mjpg.cgi, I would expect the net bit rate to be substantially less than for a sequence of jpg's, since true motion-jpg uses a lossy form of intraframe compression typically yielding a 20:1 data reduction (according to wikipedia). Indeed, I can readily see this reduction in mjpg clips made on my Canon S5is camera. It's not clear whether that is happening with the d-link DCS-930L camera (640x480, quality "high", java).
View 5 Replies View RelatedThe DCS-930L provides no date & time on video stream at mydlink, but does display those when accessing on the LAN. Is there a way to force the date/time tag to show over the web? Otherwise, remote recording might not know when an event happened?
View 1 Replies View RelatedThis causes massive 3G data to be used. If you don't close the app first it just keeps streaming and eating data + battery.This data screen cap is for 10 minutes after locking the phone with the app open.When the phone locks, the app should kill the video streaming.
View 5 Replies View RelatedI have the WAP4410n connected to a SLM2008. I tried to change to 100Mb the port in the switch but then I lost the connectivity.
But it's a giga port and it must work as a giga port. The new firmware must resolve the problem, and not to be a work around. Or what will be the next, not to use N, only G, or only 20MHz or...
I need the WAP4410n for streaming audio and video?
I've been viewing some videos streamed through the EA6500 from a Qnap 419p II NAS, and several video files are playing back extremely choppy.I can confirm that the video files play fine on the Xbox360 using a USB key and have also previously streamed these videos without any problems using a Belkin Wireless Pre-N router (that I upgraded from) streamed from the same NAS.I've attempted to configure the Media Prioritization feature, but haven't noticed any different results. I have also adjusted other various settings that haven't affected the playback in any way.
My only guess is that some of the files are encoded in a format that the router is struggling with - the video files are not HD videos, and their bitrates are generally quite low - if my old Belkin router can do it, the EA6500 shouldn't have any problems either.
how to use my lG flatron TV set to watch any DVD movie OR VCD movie show in my neighbourhood without payment fee?
View 1 Replies View RelatedWhat do I need to stream video from my laptop to my tv?
View 2 Replies View RelatedI think there is a problem with the settings on my router or something like that. When I watch videos on streaming sites the load bar tends to go up but only so far before freezing. If you slide the button along once the umbrella spinny thing gets going then the load bar will kick back into life again for a few seconds before freezing! The problem also effects downloads. Anything that takes longer the 5 or 10 seconds will fail. This has stopped me downloading simple things such as iplayer and flash updates. I know its not a problem with my computer as it effects all the machines that pass through the house. Were currently getting Virgin wireless broadband (so I dont think its a speed issue).A tecky friend of mine thinks it might be something to do with the 'packets' of information or the channel that my router is operating on
View 16 Replies View RelatedI posted this on a previous thread along with another question, but since I marked that as answered I'll post it here so people will see it.Is there any way I can use UPnP WITHOUT having to have the videos I want to stream in my WMP library? Windows Media Player has always been a pain for me, from my videos not showing up in the library when I know they're there to not being able to switch audio streams in a video. (If VLC Media Player or iTunes had a UPnP library.
View 3 Replies View RelatedI got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View RelatedI have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies View RelatedI'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View RelatedI have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedSo just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies View RelatedI upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
[url]...
With firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View RelatedI have a 655 and two TVs. One is connected to my network by a Samsung 5700 Blu Ray player, and the other is connected by x box. The x box is 20 ft away from my router and the Blue Ray is about 60 away with one wall between. The x box pulls movies down and plays them no problem, and Blue Ray takes about a minute for loading the moving, will start playing but them pauses several times throughtout the movie showing the loading sign on screen.
View 2 Replies View RelatedWe currently use the DIR 655 in our home. I has a great range, and we've never had any problems. Our house is a very tall Victorian, so some areas don't get as strong a signal as others. I'd like to set up a few addition devices to extend the coverage of our network.
I installed a DAP 1522 as a bridge to our entertainment PC. After a while of trying to sort out how to configure it everything is working there. The 1522 is connected to the PC via cable.
I still want to extend the overall wireless range to better cover the lower floors and back porch.
From reading the manual on the 1522 I am a bit confused. I understand how it works as a bridge, connecting devices via cable. Will it also extend the range is set as an Access Point without needing the devices to connect via cable?
I got a new laptop for Christmas that came with the Intel(R) Centrino(R) Wireless-N 2230 card that supports 802.11N. I am only seeing connection speeds of 1500mbps rather than the 300mbps that he DAP-1522 advertises.I found this on the d-link site but from what read on the Intel site about the card it supports the 40Mhz band. url...
View 3 Replies View RelatedI have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedI am able to stream audio from a website when i connect directly to my cable modem but when the router is connected it doesnt work. I have tried resetting the router, ping the website and get "request timed out"The firmware is up to date version 2.25 I have tried other computers that access the same network and they also cant stream the audio.I have also turned off my windows 7 firewall with no luck I can access other sites I visit and stream audio just fine so I wonder if the router may be blocking something on this website?Is there a way to allow an audio stream to come through that may be blocked by the router?
View 1 Replies View RelatedI have a readynas duo connected by cable to my dir 825,and i want to stream movies from the nas to my zbox,wich has W7 32bit and a sitecom dual N usb adapter,but it seems my wireless speed is to slow for mkv and m2ts(playback stutters),when i copy a file from the nas to my zbox i get 7,60MB using a 1,33gb file,when i copy the same file from the zbox to the nas speed is a little better around 8.20MB.all my devices are in the same room.
View 8 Replies View RelatedI want to set up a DLNA server (asus MB) to stream TV to my Sony Bravia (N based wifi) unit. I have a dir-655 (wonderful router) and am wondering if it will work to pass DLNA signals thru. It is hardware version A4 and firmware version 1.21... Will I need to upgrade the firmware? Can I get an HD signal?
View 1 Replies View Relatedi want to watch IP TV on my HTC DESIRE, i have DIR-655....how to setup udpxy proxy to stream ip-tv channels to my phone?
View 1 Replies View Relatedusing an Airport Express to stream itunes music wirelessly? I'm able to get the AE setup and can stream for about 30 minutes but then it can't be found. I'm assuming the 655 is kicking it off. I've tried changing settings on the 655 but nothing seems to make any difference. I'm able to use an Apple TV/iPhone/iPad with no issues.
View 14 Replies View Related