I upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
[url]...
I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies View RelatedI up graded to latest f/w. Now I can only log into the unit for about 1 minute before a get a limited connectivity warning, then it boots me out.
View 7 Replies View RelatedI turned it on for bridging and it did not auto setup wireless so i need to turn off WPS but my wireless option page is now blank. I rebooted, reset the DAP but still no manual config option. I found I could configure it if I switched it to AP mode but still cannot setup from bridge mode. According to manual a reset does not turn off WPS so what is the answer?
View 1 Replies View RelatedI use to have a DIR-655 and dap-1522 both worked without any issues. I recently upgraded to Asus RT-n56u and now I want to setup the dap-1522 with it.I have no issues with the Asus RT-n56u everything seems to work fine here the problem seems to be with the dap-1522 where it connects but then disconnects almost instantly.
1) Connect dap-1522 with my desktop computer via Ethernet
2) Change the LAN settings for tcp/ip v4 to manual IP
3) I set the manual IP to 192.168.0.60/ subnet mask 255.255.255.0 and the default gateway to 192.168.0.50
4) I open my web browser and connect to 192.168.0.50 and I see the dlink page and I log in fine.
5)I tried going through the wizard, picked manual and have tried both the 2.4ghz and 5.0ghz bands they are set up as WPA-Auto Personal and I enter in my password. It says settings will be saved
6) The page refreshes to the wireless one but I don't see any options here just the save config one. When I go to status sometimes it says its connected but sometimes it just says it's not I try to unplug from my desktop and take it over to where my apple tv is but it never works..One thing I should note is my asus is connected to 192.168.1.X so do I need to change the dap-1522 to 192.168.1.50? instead of 0.50?
I am trying to upgrade the firmware on my WRT54GS wireless router. I typed in 192.168.1.1 into the web browser and got to the setup menu but there is not much on the page. There are no menu options and just some of the information is on the page. None of the menu headers are listed. Is there any way to reset this so I can get the menu to work again?
View 6 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8968
Hardware Version : V1
Firmware Version : latest
ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
Region : UnitedStates
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111108 Rel.40398n
ISP : AT&T
Everything seems to work fine except that there is no Wireless option in the menu. I updated the firmware and reset to factory defaults, but the wireless option still does not appear in the menu.
Region : UnitedStates
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
Seems that Daylight Savings Time starts on March 10th, 2013 this year. The drop-down menu only goes up to 6.
I need to upgrade my location appliance. I am currently running a 2710, WCS version 6.0.196.0 and 21 4402 controllers on 6.0.182.0. There are 11 sites spread accross Canada and the Northern US. There are going to be a minimum of 4 more this year. The majority of my sites are outdoors and use 1522's. I have some indoor sites on 1242's, the biggest being an office building with 32 radios.The problem I have is I've hit the limit on clients that can be tracked on the 2710. For the record, I don't run rogue detection on all radios. I spread it out so that I don't get too many overlaps. I am looking at moving to the 3350 but see that the WIPS software does not include 1522's. Does that mean I lose my ability to detect disassociation floods etc if I go to the new platform? Or, does the context aware software still provide some notification.
View 5 Replies View RelatedJust bought myself a TP-Link WN722N Wirless Adapter. Currently I have a Netgear WNA3100 connected which works fine but I to use the TP-Link to connect to a second network simultaneously.Here's the problem.The drivers installed just fine for the TP-Link adapter. Windows shows that its connected as a USB device (USB2.0 WLAN) and Network & Sharing Centre shows it is being "Wireless Network Connection 4"(The Netgear one shows as "Wireless Network Connection 2")However, when i try to use the TP-Link one to connect to a network, it doesn't show up in the "Network Connections" menu on the Taskbar, and when i disconnect the Netgear one it says that it can't find any wireless connections at all; note that "Network & Sharing Centre" still shows the TP-Link Adapter as being connected to the PC).Tried Reinstalling the TP-Link Software, updating it, etc. Restarted PC. Disabled Netgear connection. Physically Disconnected Netgear Adapter and still no luck.
View 2 Replies View RelatedI got a DAP-1522 and here is my situation. I have a wireless router connected to the internet downstairs. I want to extend the range by creating a new wireless network upstairs. So I want the DAP-1522 to connect to the wireless router, and then become another access point upstairs.
I was able to connect to the wireless router in the DAP-1522 setup wizard, but nowhere was I able to configure that actual DAP-1522 WIRELESS setup. Nothing ever showed up on the "Wireless Settings". Just "Save Settings" "Do Not Save Settings" and the rest of the screen empty. On the status page it does show it is connected.
Am I doing something wrong or will the DAP-1522 not do this?
I want to send a WoL (wake on lan) packet to power up a PC which is wired to DAP-1522. The DAP-1522 is connected to my DIR-655 router wirelessly. So far, I have no luck. Do you know if the DAP-1522 is capable of passing the WoL? Does it need a firmware upgrade before it can do so?
View 7 Replies View RelatedI have a defective DAP-1522, or what. First off, I have never been able to access the unit at http://DLINKAP when my computer is connected directly to the 1522 via ethernet, only 192.168.0.50 works to bring up the web interface.
Second, I have more than one AP at my house, but the DAP-1522 is the only networking device I have have problems with (I am using the unit in AP mode). Basically, the problem is the wireless connection usually is much slower than my other APs (both N and G), even when the computer is physically right next to the DAP-1522. And that's when the unit is at it's best. At it's worst, I can't connect to the internet at all, even though my laptop shows full signal strength. The 1522 just seems really finicky. The problem doesn't seem to be a networking issue, because a 2nd AP that is connected through the wired portion of the DAP-1522 works perfectly, implying the 1522 is having no networking issues when using the ethernet ports. But since the problems persist with full signal strength and with the computer right next to the 1522, it doesn't seem to be a wireless connection issue either. And I have no problems connecting to any other wireless APs I own (and I own about 5 others, not that I use them all at the same time).
If I could, I would return my 1522, but I've been tinkering with it for too long now to return it. It has caused me a ton of frustration. I had a wired-only router for a long time (hence the purchase of the 1522), but just bought a new wireless-N router that is performing perfectly (as a router, and as an N AP). I hoped the old router might have not been playing nice with the 1522, but have seen no improvement with the 1522 wired to the new router (on opposite ends of my home).
Note that I use Macs only, no Windows machines. I started with the 1.02 firmware for the 1522, now have 1.20 firmware, but have noticed no improvements with my issues.
Using as AP. Last Tuesday in the middle of a Netflix movie the video stopped. Now the wireless portion of the DAP-1522 refuses to pass any type of video. Everything else works (email, Google, Facebook, etc.). I can get to Netflix, Youtube, Yahoo, etc. .....but none of them will pass video.
Using a direct wired connection to the DAP-1522 everything works. Netflix, Youtube, etc.
Download speed checks at 17.74mbps.
I'm running the 1522 as a bridge with v1.21 firmware. I have 2 devices wired to it. I have Wireless MAC cloning disabled (not checked). If I scan my network using a tool such as ipscanner (http:url.....) the devices attached to the bridge are being listed with the 1522's MAC address - not their own.
The connected devices should be showing up with their own MAC addresses. The 1522's address should only be displayed IF MAC cloning is enabled and IF the cloning mode is set to Auto - is my understanding of this feature incorrect or is my 1522 not performing as spec'd?
I am thinking of getting the DAP-1522 access point but I wondered. Can I set it to broadcast on 5GHz for my laptop and ipad, so they can stream video. Then set the guest zone to broadcast on 2.4GHz just for my lame printer, my printer does not have LAN and only wireless b & g. If I do put the printer on the guest zone and I enable routing between zones, will my laptop be able to print to my printer?
View 1 Replies View RelatedI have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies View RelatedIf I turn off the wireless on my DAP-1522 in bridge mode, will it basically become a Gig Switch?? I've changed my network around abit and don't need it in bridge mode at this point but would love to use it as a plain switch. Would this do the trick??
View 3 Replies View RelatedSo just recently purchased the DIR-825 and DAP-1522. At this point I just want to get the DAP-1522 to work as a wireless access point to my DIR-825. So my wireless laptop would connect wirelessly to the DAP-1522 and the 1522 would go wireless to the router. Pretty basic I guess. I was planning on using the WAP to strengthen the 5 GHz signal to the router but again, at this point, I would be happy to get the 2.4 GHz working.
I've been working on this since last night and got frustrated and went to bed. I woke up fresh and decided to try again and I'm not having making any headway.
DIR-825 is connected to my DSL modem and has no problem accessing the internet. I can connect to either 2.4 or 5.0 directly from my laptop with no problem at all and have access to the internet. Encryption is disabled. It worked with encryption but I turned it off to troubleshoot this AP problem.
It should be simple but I must be doing something wrong. BTW is there a way to scan for network devices from the router or the access point? I tried discovering each device with the wireless setup button on each device but they don't recognize each other so I'm configuring this manually.
So the DAP has access point enabled and 802.11 is running in mixed mode. I've tried different variations but nothing has worked. I've tried 20 mhz and 20-40 auto mhz channels but same problem. Wireless security is off for troubleshooting at the moment.
DHCP server is disabled and I've assigned the DAP an available ip from the router's dhcp range. I can connect to the DAP both wirelessly and hard wired. The problem is that it can't seem to connect to the router. So my laptop can connect to the router and ha internet access. And it can also connect to the DAP but does not have internet access. The ip is showing auto configuration 169.x.x.x when connected to the DAP so I'm not getting an ip. Is the router supposed to assign the ip to my laptop through the DAP? But again, if the DAP can't communicate with the router, then that would explain why I can't get an IP.
i cant create dlink acess point password , if I am going 192.168.0.50 then showing error massages , I am check two three computer , then the same error coming
View 1 Replies View RelatedWith firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View RelatedI'm running a Windows Server 2008 Enterprise Edition server that is currently the domain controller, and a Windows 7 Ultimate client. I have a 'Test' user for messing around with group policy - anyway, on the client Start Menu it has 'Test User' which leads to some form of libraries folder. Is it possible to restrict the link without removing their name?
View 3 Replies View RelatedI have the revision b version of the dir-655. I'm having a couple issues which im not sure if are related to the dir-655 or something else.
I used to be able to do this, then all of the sudden (I may have changed something) I cannot anymore. The issue is: If I try and access my linux server using http://[My Public IP Address]/ from *inside* my LAN, It will time out and not connect. If I try and access my same public ip address from *outside* my LAN, it works fine.
My router was noticeably slow to respond when navigating the menu system. Then, I changed the ip address to 192.168.0.2 (previously it was 192.168.0.1) and all of the sudden its fast again. I tried rebooting and power cycling before I changed the IP and it was always slow using 192.168.0.1.
We currently use the DIR 655 in our home. I has a great range, and we've never had any problems. Our house is a very tall Victorian, so some areas don't get as strong a signal as others. I'd like to set up a few addition devices to extend the coverage of our network.
I installed a DAP 1522 as a bridge to our entertainment PC. After a while of trying to sort out how to configure it everything is working there. The 1522 is connected to the PC via cable.
I still want to extend the overall wireless range to better cover the lower floors and back porch.
From reading the manual on the 1522 I am a bit confused. I understand how it works as a bridge, connecting devices via cable. Will it also extend the range is set as an Access Point without needing the devices to connect via cable?
I got a new laptop for Christmas that came with the Intel(R) Centrino(R) Wireless-N 2230 card that supports 802.11N. I am only seeing connection speeds of 1500mbps rather than the 300mbps that he DAP-1522 advertises.I found this on the d-link site but from what read on the Intel site about the card it supports the 40Mhz band. url...
View 3 Replies View RelatedI have a brand new DAP-1522 A1 connected to an 802.11n wireless LAN in bridge mode. Running in the 2.4GHz band with WPK-2 and AES security/encryption.Everything runs fine 99% of the time, but once a day or so the wireless LAN connection on the DAP-1522 drops and then takes about two minutes to re-connect. It re-connects and then everything is fine for a day or so until the next dropped wireless connection episode on the DAP-1522. I know my 802.11n wireless network is 100% fine as during the dropped connection to the DAP-1522 I can connect directly to the 802.11n wireless network (running from my gateway/router) using my other computer, no issues.I've seen some posts on this forum that the A1 version of the DAP-1522 hardware is not 100% compatible with the 802.11n network standard and there will be intermittent wireless drops. If this is true, it's just insane. All I can say is I can't believe DLink would allow a product to be sold that won't work properly on 802.11n networks.I check the logs each time I see the dropped wireless connection and all that shows is the following.1) Negotiating connection 2) 4-way handshake success [mac address]There's no message in the logs about why the wireless connection dropped, but I assume it has something to do with re-newing a key for the wireless network as the successful key renewal messages are the only other messages in the log. When the wireless network dropped I don't see the successful key renewal message at the time I should see it.I thought this DAP-1522 would take 15 minutes to configure in bridge mode and then I'd forget about it. Spend too much time on this already, so a bit disappointed with this DAP-1522 and DLink tech support....though when it's connected to the 802.11n wireless LAN it works fine.
View 14 Replies View RelatedMy D-Link DAP-1522 wireless bridge is connected through a single cat5 cable from the LAN port on my PC to the 1st LAN port on the D-link unit. At the moment, it is in bridge mode, with the blue power indicator on, the orange wireless connection light flashing, and the 1st LAN port connection periodically wavering indicating that it is communicating with my PC. When I attempt to configure the DAP-1522 via my internet browser, (IP 192.168.0.50) I get an error saying that the requested webpage does not exist.
View 6 Replies View RelatedI recently had a networking guy set up a VPN for me, but for it to work properly he had to change all my IP addresses to 192.168.10.xx from 192.168.0.xx. My DAP-1522 (in bridge mode) continued to work but I am unable to log on to it, I think because it's address is 192.168.0.0. I have run into some other issues which makes me think I may need to upgrade the DAP-1522 firmware and/or assign it an address beginning with 192.168.10.xx, however I can't log on to the bridge. (Nor do I know how to change or possible reassign the DAP-1522's address through my router, a DIR-615).
View 5 Replies View RelatedMy problem is two-fold:
1. the DAP-1522 will not connect to the 5GHz network of the DIR-815. Although, this doesn't surprise me as none of my 5GHz-capable devices see it, other than intermittently and at low signal. It is most likely an issue with the 815's 5GHz radio/network.
2. OTOH, the 1522 does appear to connect to the 815's 2.4GHz network just fine. However, there is no Internet access for any of the devices connected to the 1522's ports.
I know the 1522 can work correctly on 2.4GHz, as it previously did fine with my prior 2Wire router from AT&T. (I've just switched to Comcast, using the DIR-815 connected to their SMC modem.)
Also, I know the router and modem work fine (at least with 2.4GHz), as all of my wireless devices connect easily and with screaming bandwidth to the router and Internet.
I have a WIN XP desktop which I successfully connected to the 1522 AP - as evidence of the GUI to program it. I have the 1522 set to Bridge Mode via the switch on the unit. The 1522 has hardware version B1 and Firmware version 2.000. I joined my wireless network successfully as evidence of the Status page showing it's successfully connected and bridged to my network. I then disabled my USB wifi NIC in hopes of using my hardwired connection to the 1522 to get on the internet.
Wireless Radio : Enabled
Bridge State : Connected
MAC Address : fc:75:xxxxxx
802.11 Mode : Mixed 802.11a, 802.11g and 802.11n
Band Width : 40
Channel : 6
Network Name
(SSID) : cleveland
Wi-Fi Protected Setup : Enabled
Security : WPA2-PSK
I have dap-1522 version A Browser IE8 with lestest updates.
I downloaded the DAP1522_FW_1.31zip went I try to upload via the 1522 admin error not correct file.
I try three different way to download it, could the file be bad on dlinks web site?
I have just discovered after three weeks of testing that DAP-1522 wireless bridges are not compatible with all the new Pioneer AVR's that support internet radio and Iphone control. Anytime a DAP-1522 is powered on and on the same subnet mask as a Pioneer receiver it will cause the Pioneer to loose it's connection every 30 minutes. The receiver is then not able to connect unless it is powered off and on again. The DAP-1522 will cause this even if the Pioneer is hardwired to a router and nothing is plugged into the DAP-1522. This affects all new models of Pioneer receivers including the Elite line like I have.
I have tested this with 3 differnet Pioneer receivers and 2 DAP-1522's and always got the same results no matter what the settings were and with the 1522 in AP or bridge mode. Other Pioneer receiver owners experiencing constant disconnect problems on another forum have now also confirmed they have DAP-1522's.....and they are also pissed after spending countless hours troubleshooting.
I talked to Dlink support today and they will not admit to a problem so I can't wait to contact Pioneer tech support on Monday to let them know I have found the reason they are seeing returns on their new receivers (some cost as much as $7K) since many of the new owners like myself are exchanging them thinking they got a bad one. I'm sure Pioneer will test this immediately and force a Dlink fix or turn it over to the FCC.At this point I just wish I could get my money back since I have also already confirmed that a netgear bridge works just fine. Come to think of it, I know Dlink has a new refund policy, but I will check with my state district attorney to see if they can legally keep my money even if the product doesn't work. I don't see anything on the outside of the box with this policy so therfore I wasn't given fair warning of the policy before purchase and would not be expected to know it since it is not industry standard. Let the games begin.