D-Link DIR-655 :: Router Was Noticeably Slow To Respond When Navigating Menu System
Apr 14, 2011
I have the revision b version of the dir-655. I'm having a couple issues which im not sure if are related to the dir-655 or something else.
I used to be able to do this, then all of the sudden (I may have changed something) I cannot anymore. The issue is: If I try and access my linux server using http://[My Public IP Address]/ from *inside* my LAN, It will time out and not connect. If I try and access my same public ip address from *outside* my LAN, it works fine.
My router was noticeably slow to respond when navigating the menu system. Then, I changed the ip address to 192.168.0.2 (previously it was 192.168.0.1) and all of the sudden its fast again. I tried rebooting and power cycling before I changed the IP and it was always slow using 192.168.0.1.
I just purchased an E-3000 and when I log into the user interface it seems changing pages and saving settings takes forever. I click on a section in the router menu and it takes what seems like 30 seconds for the page to change or accept the new settings. It's not my browser it's definitely a Linksys Router issue. I updated to the latest firmware and latest Cisco Connect software as well. Is this slow user interface a normal thing with these routers?
Region : UnitedKingdom Model : TD-W8968 Hardware Version : V1 Firmware Version : latest ISP : french orange
I am trying to set up port forwarding on this router but it seems I need to use virtual servers but in all the guides there is a menu for this under the advance settings nat menu.I do not have that option, I have downloaded the latest firmware but still nothing.
I have a DIR-655 (HW rev A2) that has worked mostly fine for a long time. Today I decided to do a firmware upgrade, and in preparation I backed up my custom config settings and did a hard reset via the factory reset button on the back of the unit.
Since then, the unit itself has been inaccessible from my computer. If I connect the DIR-655 and a PC with a network cable, the appropriate light goes on on the front of the router, but the client does not lease an IP address from the router and I can't access the router home page at 192.168.0.1.
I have tried the reset button again and also power-cycled multiple times, and I have tried connecting from multiple computers, all with the same unsuccessful results. how to "un-brick" the device?
Just bought myself a TP-Link WN722N Wirless Adapter. Currently I have a Netgear WNA3100 connected which works fine but I to use the TP-Link to connect to a second network simultaneously.Here's the problem.The drivers installed just fine for the TP-Link adapter. Windows shows that its connected as a USB device (USB2.0 WLAN) and Network & Sharing Centre shows it is being "Wireless Network Connection 4"(The Netgear one shows as "Wireless Network Connection 2")However, when i try to use the TP-Link one to connect to a network, it doesn't show up in the "Network Connections" menu on the Taskbar, and when i disconnect the Netgear one it says that it can't find any wireless connections at all; note that "Network & Sharing Centre" still shows the TP-Link Adapter as being connected to the PC).Tried Reinstalling the TP-Link Software, updating it, etc. Restarted PC. Disabled Netgear connection. Physically Disconnected Netgear Adapter and still no luck.
Region : UnitedStates Model : TD-W8960N Hardware Version : V3 Firmware Version : 1.4.0 Build 111108 Rel.40398n ISP : AT&T
Everything seems to work fine except that there is no Wireless option in the menu. I updated the firmware and reset to factory defaults, but the wireless option still does not appear in the menu.
I upgraded the firmware on my newly acquired DAP-1522 from v1.02 to v1.21 (the hardware ver is A1). But weird thing happened after the upgrade--the Setup->wireless network settings portion of the set up menu disappeared! I re-flashed the upgrade once more and it's still not showing. Reboot the AP--same thing!
I'm running a Windows Server 2008 Enterprise Edition server that is currently the domain controller, and a Windows 7 Ultimate client. I have a 'Test' user for messing around with group policy - anyway, on the client Start Menu it has 'Test User' which leads to some form of libraries folder. Is it possible to restrict the link without removing their name?
I use a dongle from my ISP as my main internet connection source. I needed to do a full system restore because one of the windows system files got corrupted.After the restore, my internet connection was extremely slow. I restarted the computer and I got my normal fast speed but only for about 10 minutes and it is now very slow again (about 10 mins to load Google home page, for example).Internet speed was never an issue before the restore. Also I tried the dongle on my work laptop at home and it's fine.I'm using Windows XP. I've tried everything suggested at Slow Computer/Internet AFTER complete system restore but it is still slow.
Iam running Windows XP sp3 ,firefox browser and my router and modem are fine. iam getting transferring /waiting for 5 minutes before it loads. each transaction on the page takes minutes. Ive disabled/repaired/enabled internet connection" several times with no success. Where can I look in my system?
I have an older D-Link DGL-4300 wireless router, I've purchased a wireless home security system and can't seem to get the 2 connected. I've tried resetting the router & modem (powering down & waiting from 1-5 minutes), and my router just won't read the port that I've plugged the security system ethernet cable into.I think the problem is my firewall but I don't know how to set it to allow the router to read the port that I've plugged into, or it could be the firewall that my anti-wirus has or possibly both.My equipment is Comcast cable, router (as noted above) and a D-Link DCM-202 modem, Windows XP 3, and Norton anti-virus. Now I also have my phone through Comcast and it has it's own modem.
I have a two routers running from one connection first the master which is a Dlink dg500 - i think all is fine there. Secondly I have a slave router running all the wired/wireless things in the kids rooms its a netgear and when i say 'slave' I figured out if you put the input from the first router into port1 instead of input it works as a slave.
Problem is I need to get into the router menu on the netgear, it was ip add 192.168.1.1 then when i slaved it it was 10.0.0.1 - (I think) but I have tried recentley to get onto it and can't for the life of me. I have tried wirelessly and through ethernet cable but can't get the menu.
U just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
In each case, the routers have functioned flawlessly for a period of 2 to 8 months, then suddenly begin to require daily to hourly reboots to keep the speed up, and often times fail to respond to any web activity whatsoever. Ping tests are intermittent, sometimes failing but other times succeeding while web sites remain unresponsiveFor three years I lived with two or more room mates at a time, each of us with our own computer (or 2) and all doing a lot of peer to peer downloading. I realize a router can overheat during heavy use like this, so buying new routers so regularly has seemed vaguely understandable. However it doesn't seem like that is the case in my most recent failure.I've lived alone for the past 3 months, and have owned the Belkin Play Max N600 HD since. I have NOT been P2P downloading or putting a heavy load on my router in any way (or so it seems). Yet as of about two weeks ago, it has suffered a major slowdown just like all of its predecessors. Yet my 30 mbps internet connection roars to life the moment I plug the modem directly into a computer.
My desktop remains on 24/7 but like I said before, I do not do constantdownloading/uploading. Both wired and wireless connections are effected equally, and I have always kept all my routers WPA encrypted.When websites become unresponsive on my Belkin today, it is usually after everything has been sitting idle for some time (overnight, or all day while I am at work). Speaking of work, today is a perfect exampleI remoted into my home desktop and was able to interact just fine, yet when I would launch a browser and try to load any website at all, I get absolutely nothing. I had to transfer a text document through DropBox (which also still worked) because I couldn't get Google Docs (or gmail) to load on the remote computer
I have a belkin f7d2301 and I cannot access the startup menu it says startup not found I have remove program and reinstalled it. is the disc bad. i also cannot do auto updates because it can't find startup location.
I am trying to upgrade the firmware on my WRT54GS wireless router. I typed in 192.168.1.1 into the web browser and got to the setup menu but there is not much on the page. There are no menu options and just some of the information is on the page. None of the menu headers are listed. Is there any way to reset this so I can get the menu to work again?
I recently bought a Linksys WAG160N v2 model to replace my old setup of a Linksys WRT54GL + ASUS AM604g (ADSL2+ Modem) i had.I've set it up to dial my ISP's PPPoE connection as i had on the previous setup exactly, And it seemed to work at first.But now i've randomly noticed the connection just dies - the router doesn't respond to wireless at all anymore, and connecting from a wired machine shows the PPPoE link died, while the log says something along the lines of "PPPoE connection terminated: transport endpoint not connected" followed by a big number with lots of zeros and :'s. Probably some kind of IPv6 error address? note that i am not using IPv6 myself nor does my ISP provide any such addresses.
I've already upgraded the firmware to latest and installed the newest WiFi drivers on the machine i was connecting from wirelessly (has an Intel Wifi Link AGN5300 module).
I just purchased a Linksys Cisco E900 router and hooked it up to my Internet cable. The Internet service that my ISP is giving me is PPPoE, fiber link (100 Mbps).
I did the set up. I connected my computer (via Ethernet cable) and my laptop (via wireless) to the router.
Now... there are other wireless networks around me. The WI-Fi channel my router fixed to is 1, apparently - saw it from the settings. But I can't find a menu anywhere in the router's gateway (192.168.1.1) from where I can change the wireless channel, wireless bandwidth etc.
I'm trying to register my new linksys e2000-ew wireless router but it doesn't show up in the selection pull down menu. When I try the e2500 it says my serial# isn't correct.
I 'd like to use the access restrictions capabilities of the WRT610N v2. Unfortunely the "Access Restrictions" menu is missing in the admin GUI; I 've got all the others : "Set -up", "Wireless", "Security", Storage, Applications and Gaming, Administration and Status. I've checked the Firmware already and i'm using the very last one available on the cisco web site. I also noticed that I do not have the "Linksys by Cisco" text on the upper left corner as one can read on user guide but just "Cisco".
My Router is incredibly slow, what can I do?I currently have a D-Link DSL-2680. My ISP is TalkTalk.I have had problems with it since day 1, I had it running at one point on 300Kbs when downloading, and for me that was good. But now I am running 9.8Kbs when downloading and sometimes slower. I did a speed test and that reports speeds of 0.2Mbs.I have done a tracert and it's results were;Microsoft Windows [Version 6.0.6000].
Okay i just got the DIR-615 N Router and at first i was getting 40 ping on speedtest.net but now I'm getting 360 ping which is really frustrating since i upgraded because my old one was having troubles and also when i get to the check connection in the setup i am getting Your new router does not appear to be connected properly.
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
I recently switched from Linksys WRT54G router to MediaLink router. My wired connection speed stayed the same but my wireless speed degraded significantly - roughly from 5-8mbps to 200-300kbps.I measured my wireless speed both on win7 laptop and iPad. My Roku box is also struggling. All devices were in the proximity of the router.I tried changing encryption (WEP/WPA2/no encryption), mode (from b/g/n to b/g to just g), and different channels. Nothing worked, the speed is still very slow.
I had my Dir-655 router for over a year & this is is a first.My firmware is 1.21 & I only use my router for gaming when I'm not on my PC for home use. I have only one PC in the house that is not shared, I have also not downloaded any virus or maleware.So the past month I decided to buy a wired ethernet cord to connect to my gaming systems rather than using the wireless option to get an extra bit of speed. That has been working fine up till yesterday when all of a sudden my download speeds dropped from around 20Mb down to barely 1Mb down (I can't even get the speed test site to fully load anymore). The upload & ping remains unchanged though. Only my Download speed is being affected. This is both when I'm on the PC & when I'm online gaming.
I unplugged my D-Link router & plugged my modem directly to my PC & I got back the 20+Mb speed, so the modem or cable company are not at fault (I even called them to see if there were any problems on there end).
-I tried turning off my Firewall on my PC. -Resetting & rebooting both my modem/router/PC. -using different DNS numbers. -using /flushdns. -using /Iprenew. -Messing around with my router configurations such as: turning off QoS Engine. turning off wireless. turned of MAC filtering. unchecked "Add DHCP Reservation". unchecked SIP.
None of it worked. I'm still browsing at around 56k dial up speed for the past day+!I read up on the internet for similar problems, but the only solutions I saw was turning off the firewall on the PC, but that hasn't worked at all.
This only started about a week ago and everything was working fine before then. My router is causing my internet to be slow (I know this because it goes at normal speed when I am connected directly to my modem)
Region : Malaysia Model : TL-WR1043ND Hardware Version : V1 Firmware Version : 3.13.13 Build 120605 Rel.38634n
The connection is slow when I connect my notebook to the TP-Link TL-WR1043ND wireless router. If I connect my notebook directly to to the ISP modem, the connection speed back to normal.
Region : Brazil Model : TL-WR841ND Hardware Version : V7 Firmware Version : 3.13.9 (Last) ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Argentina Model : TL-WR1043ND Hardware Version : V1 Firmware Version : ISP :
Region : Netherlands Model : TL-WR941ND Hardware Version : V3 Firmware Version : 3.13.9 Build 120201 Rel.54965n ISP : Ziggo
I currently have a issue with my TP-link WR941N.When I first connected the router I had a good internet speeds of about 70 mbps. My max provided by the ISP is 120Mbps but 70 was acceptable for me. Recently however the connection is terrible. I regularly have a speeds of 6Mbps via the router, When i directly to the modem via kabel I get a speed of 120Mbps. Therefore I ruled out that the connectivity problem is due to my ISP.
I got 3 new TP-Link WA901ND PoE access points for a wireless network I manage. Right now I'm using the stock injectors that came with them because I need to get adapters still so I can use them with my PoE switch.
Hardware Version: v2 Firmware Build: 3.12.16 Build 120224 Rel.61005n Wireless Mode: Access point Channel: Auto Mode: 11bgn mixed Channel Width: 20/40MHz Max TX: 300MBPs
About a week after getting these units installed and having them work great, I started running into problems. One of the unit's system light was not on, and I could not connect to the access point from my phone, or log into the web interface. I did a soft reboot (unplug for 30 seconds, plug back in) and it seemed to work fine, but then I had the same problem, and soon both units were doing it. I thought i might be pushing the distance limit the stock injectors have, but then I started having the same problem with a unit that is 10 feet from the injector.
