D-Link DIR-601 :: So Slow In Router Admin Pages

Jun 26, 2011

I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?

View 3 Replies


ADVERTISEMENT

D-Link DIR-825 :: Admin Pages Slow And Locking Up?

Dec 7, 2009

I am having issues with my freinds new DIR-825 Rev:B1 Firmware:2.02NA, The admin pages are intermittently slow to load and sometimes wont load until I power cycle the device.  I am using IE8 on vista x64, and have the issue on all pc's on the network.  Is there a work around for this?

View 7 Replies View Related

Linksys Wired Router :: BEFSR81 V3.1 Blank Admin Pages?

Jan 28, 2010

BEFSR81 v3.1 Current firmware 2.51.4 build 600 (09-4-2009)The Web Admin pages become dysfunctional after the router has been up 3-4 days displaying only a blank white page. Viewing the page source shows that the HTML is incomplete.I am not sure of the exact firmware version where this problem originates, I noticed it after flashing to 2.51.4 build 400 but cannot remember which version was running before the update. Just flashed to 2.51.4 build 600 last week hoping the new version had corrected the problem. Still broken.The router remains completely functional but the Web interface does not work correctly after 3-4 days.I have tried re-flashing the firmware and have gone as far as resetting the router both before and after the flash, even tried 30/30/30 resets but the problem with the Web interface remains.Re-booting the router every 3 days is not the best “solution” as my network is running DHCP. I would rather not fall back to older firmware as ver 2.51.4 build 400 corrected the DHCP errors on my Windows machines and decreased the initial connection time when machines boot up. I have read in this and other forums where others are having the same problem with this router/firmware but have been unable to find a working solution which leads me to believe the actual problem resides in the later firmware builds.

View 9 Replies View Related

D-Link DIR-825 :: Slow To Bring Up Settings Pages

Dec 26, 2011

I'm using a Dell computer CPU i7 8 gig of ram. It is wired in to the router. Why does it take so long to log into the router and bring up the different pages in the settings. I have never seen a router take so long. I have not updated the firmware version 2.02NA. I have not upgraded it yet. oh I have a cable connection. When I surf the web the pages come-up fast.

View 13 Replies View Related

D-Link DIR-615 :: Pages Won't Load / Internet Speed Is Slow

Jan 3, 2012

I`m new here I recently purchased the dir-615. I started configuring with cd but i couldn`t get past the step where it should verify if cables are plugged in , so I did it manually. Some pages won`t load , internet speed is slow ( Both wireless and lan speed ) . I am using a PPPOE connection , I even got my ISP to check my settings, and he said it was alright but it reduces my speed by a lot. Usually I download with 1 MB/s with the router on wi-fi I hardly get 50 kb/s and on lan max is 100 kb/s.

View 1 Replies View Related

Linksys Wireless Router :: WRT160NL - Slow Admin Interface

Mar 6, 2013

I took one and a half hours to get everything set up, I've got a PPoE connection, my problem is that ever since I entered the administration interface each and every page takes 2-5 minutes to load, it's absurdly slow, also, when trying to setup my WiFi, it timed out several times, I updated the router to the latest firmware, the same issue, it took me 4-5 retries to get WiFi set up properly. Sometimes navigating from page to page is quicker, 30-40seconds, but still those are some big times.
 
Is this normal behavior or do I have a hardware problem and I need to take it back and request a new one?
 
Mention: I am wired from a laptop, all the lights are blue, blinking nicely.

View 9 Replies View Related

Web Pages Slow And Timing Out?

Nov 17, 2011

I am having a major issue, system wide with web pages timing out or loading slowly - we are using a Sonicwall as our content filter and firewall and to assign DHCP, we are a windows environment with both Server 2003 and 2008. Here are the results of a few tracert commands I ran.

C:Userscaleb>tracert Google

Tracing route to Google [72.14.204.103]
over a maximum of 30 hops:
1 3 ms 3 ms 3 ms 10.240.163.121
2 4 ms 3 ms 4 ms 67.59.235.245
3 * * * Request timed out.
4 6 ms 5 ms 6 ms 64.15.1.169

[code]...

View 2 Replies View Related

MSI Netbook Is Very Slow On Loading Pages?

Dec 4, 2012

MSI netbook. It used to be very loading pages but now is is very very slow and has been for a month or so.

View 4 Replies View Related

Dell :: XPS 8300 - Slow Loading Of Web Pages

Mar 29, 2012

I just bought a XPS 8300, I use Google Chrome for a browser, cable modem internet connection, and quite often, web pages will not load quickly, or will take a couple of reloads to load properly.  Any advice on how to cure this annoying trend of mine?

View 1 Replies View Related

D-Link DIR-601 - Access Modem Router As Admin?

Feb 26, 2013

I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?

I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.

View 4 Replies View Related

D-Link DSL-2680 - Can't Connect To Router's Admin Page (timeout)

Feb 28, 2011

For about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.

Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:

I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.

All I want to do is just port forward my game servers again without the use of Hamachi or other programs

View 2 Replies View Related

D-Link DIR-655 :: How To Access DSL Modem Setup Pages

Apr 16, 2011

I would like to be able to access my DSL Modem's http setup screens from my networked computers via my DIR-655 (rev B) router - but I do not know how to get the router to route to the WAN port.

At first, I had my DSL Modem's LAN IP at 192.168.0.1 and my DIR-655 at 192.168.1.1 and the rest of my home network at 192.168.1.xxx; because I had read on a forum that having the modem on a different subnet prevented potential routing problems.  When I pointed my web browser to 192.168.0.1 - it would just timeout (I kind of expected that).

Now (willing to try anything), I have my DSL Modem's LAN IP at 192.168.0.2 and my DIR-655 at 192.168.0.1 and the rest of my home network at 192.168.0.xxx (DHCP range is set to assign hosts from 64 to 254).  When I point my web browser to 192.168.0.2 - it still just times out.

The DSL Modem is setup in transparent bridge mode.  And everything else is working well with the home network.

How can I get the DIR-655 to pass/route my http connection to the DSL modem?

View 10 Replies View Related

D-Link DIR-825 :: Prevent Access To Setup Pages Via Wireless?

Jan 16, 2012

Just bought myself an 825.  I've got it set up and working, but how do I prevent wireless users from accessing the setup pages for the router?

I only wish wired access to the setup pages. I'm used to doing this on my old linksys, but can't find the setting on the new router.

View 3 Replies View Related

D-Link DAP-1522 :: ADSL Web Pages Not Loading Properly

Feb 17, 2012

I'm connecting to the internet via ADSL. The modem is in our living room and has a DIR-655 connected to it. Also connected are an IPTV set-top box and an Xbox 360. In our office room we have 2 computers and a Buffalo LinkStation hard drive connected by wire to a DAP-1522 which is working as a bridge for the wireless network created by the DIR-655. The reason for this configuration is that the set-top box refused to work with IPTV through the wireless bridge. Before we got IPTV, the bridge was in the living room and was primarily used for Xbox, while the modem was in the office and allowed all desktop PCs to connect by wire.

Ever since we've had the desktop PCs connected via the bridge, surfing has been difficult. Download speeds are good, but very often webpages simply refuse to load. The browser just says "Connecting to [internet address here]. For example, I might log on to Facebook, have the front page load and then I try to open a picture someone has uploaded, but nothing happens. Clicking links, nothing happens. Clicking anywhere, nothing happens. Put a new address in the address bar, nothing happens. It just tries to connect the addresses, but won't.After waiting a while, or restarting the browser, it might work again for a while.

Is it my new modem, the DIR-655 or the DAP-1522? All devices get their IPs from the ADSL modem to ensure proper networking between the devices. Streaming from the NAS to the Xbox is flawless.

View 4 Replies View Related

D-Link DAP-1522 :: Access Configuration Pages Via Wireless

Jan 9, 2012

I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection.  After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.

View 9 Replies View Related

D-Link DIR-655 :: Sometimes Not Serving Pages On Wired Connection After Firmware Upgrade

Jan 4, 2013

I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages.  This shows up as a DNS error, stating the DNS lookup failed.  If I wait a bit and reload the page, it will sometimes resolve itself.  If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue).  This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on).  I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.

My security setup, if for any reason it matters, is WPA2 with MAC address filtering.

View 4 Replies View Related

D-Link DIR-655 :: Can't Get To Web GUI Admin Page

Oct 30, 2011

I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout.  Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem.  Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.

View 5 Replies View Related

D-Link DIR-615 :: Can't Log Into Admin To Make Changes

Dec 12, 2012

I have a DLink N300 (DIR 615), firmware 9.02NA.I've been trying to log into the "admin" but was only able to once. When I did get it everything was greyed out so I couldn't make any changes.

View 1 Replies View Related

D-Link DIR-601 :: Can't Login As Admin

Jan 6, 2013

i'm having some trouble logging in as admin. I leave the password section blank as directed but it comes up as "incorrect password".  I then tried the same using the "User" and it worked just fine but i cant change any of my settings. 

View 6 Replies View Related

D-Link DIR-655 :: Not Logged In As An Admin

Jan 28, 2012

I just bought the Dir-655 with 2.00 firmware. I am having trouble with my NAT on my game system and I have tried everything but I have everything setup on my router where it needs to be. I read somewhere, where a guy was having my same trouble and he upgraded his firmware to 2.03na. I have tried with no success whatsoever.

Downloading the file from the d-link website with no problems. But i keep getting the same message when i try to upgrade the router saying the file may be corrupt, the router is to busy, or I am not logged in as an Admin. I am the only one using the internet and I am logged into my router as the admin. it wont even start uploading the firmware to my router..

View 9 Replies View Related

D-Link DIR-655 :: Can't Connect To Admin Page

Feb 19, 2013

I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...

View 1 Replies View Related

D-Link DIR-601 :: Unable To Get WAN Admin Access?

Apr 13, 2012

Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)

View 3 Replies View Related

D-Link DIR-825 :: Can't Seem To Login Into The Admin Console

Mar 12, 2013

I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w

View 1 Replies View Related

D-Link DIR 655 :: Blocking Website Of Admin

Apr 5, 2011

I have a dir-655 a3 router that is blocking my website ip address.I could previously access this site until one day, without changing any router settings, it started blocking communication to my website. pings, tracerts, web browsers, everything simply times out. It resolves the IP address ok but doesn't go any further than that. I was on firmware 1.31 and have now upgraded to 1.35NA, but no luck. I have also tried resetting factory defaults to no avail. If i bypass the router and plug my computer straight into the modem, the site loads fine. so its definitely the router. I have tried this on a number of devices to make sure. It appears that for some reason the router is blocking that specific IP address as it is on a shared hosting and I can't access any other sites on the same IP address. Does the router check the IP address with any web service before returning the request?

View 4 Replies View Related

D-Link DIR-655 :: Admin Interface Has Failed In Some Way

Jun 20, 2011

Bought a new DIR-655 Rev B a few weeks ago.It's web admin interface has failed in some way.  The device is still passing all user traffic in both directions, but attempts to connect to the admin interface with my web browser, from both the wired inside and the WAN outside fail.  I can telnet to the actual tcp port number that it's configured for and establish a connection, but I can't get any response from it.  At this point I'm expecting the only way I'm going to clear the condition is to power cycle the device when I get home from work.  It is to note I have the device configured for https for the admin interface.  Perhaps that's the more 'advanced' feature that's newer and is exhibiting some kind of bug, I wonder.  I'm running the latest firmware available from D-Link. 

View 5 Replies View Related

D-link Dir-615 :: No Wifi And Cannot Access Admin Homepage Via Ethernet

Mar 19, 2011

I can however connect to internet ?

Tried Explorer & Firefox

View 1 Replies View Related

D-Link DAP-1522 :: Can't Access Admin Screen After Connected

Nov 30, 2011

I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.

On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled

I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:

a). Reset DAP-1522

b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522

View 3 Replies View Related

D-Link DCS Network Camera :: 920 - Changing Admin Password?

May 16, 2010

Im having some problems changing my admin password on my DCS920

I know the default login is Login: admin / Password: "blank"

So I go into maintence, and there's an option to change the password.

it lists:

old password
newpassword
confirm

So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.

A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work

I type leaving the username blank, and type in new password... WONT WORK

I type admin, and new password again.. WONT WORK

I try password with first letter capital.. WONT WORK

I try password with ALL CAPS... WONT WORK..

Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.

Am I doing something wrong in changing my password ?

I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.

View 4 Replies View Related

Home Network :: D-link Dsl2500u - Cannot Connect To Admin Interface?

Dec 4, 2012

I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why

View 2 Replies View Related

Broadband :: D-Link DSL-2680 Router Is Slow

Apr 22, 2012

My Router is incredibly slow, what can I do?I currently have a D-Link DSL-2680. My ISP is TalkTalk.I have had problems with it since day 1, I had it running at one point on 300Kbs when downloading, and for me that was good. But now I am running 9.8Kbs when downloading and sometimes slower. I did a speed test and that reports speeds of 0.2Mbs.I have done a tracert and it's results were;Microsoft Windows [Version 6.0.6000].

View 2 Replies View Related

D-Link DIR-615 :: Slow Internet Speeds After Getting Router

Feb 27, 2012

Okay i just got the DIR-615 N Router and at first i was getting 40 ping on speedtest.net but now I'm getting 360 ping which is really frustrating since i upgraded because my old one was having troubles and also when i get to the check connection in the setup i am getting Your new router does not appear to be connected properly.

View 3 Replies View Related

Tp-link Adsl2+ Wireless :: Td-w8960n - Disable Admin Access Over Wifi?

Nov 21, 2012

Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :

Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.

View 4 Replies View Related

TP-Link Dual-Band Wireless :: WDR4300 Admin Page Ssl Option?

Apr 6, 2013

Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :

I have a question regarding the admin page on the router. Default it seems to accept only http access and I cannot find the option to switch this to ssl over https. Now the admin password goes across the WLAN in clear text which is not secure and not what I want. Is there any way to change the setting so the page is only accessible through https?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved