D-Link DIR-655 :: Admin Interface Has Failed In Some Way
Jun 20, 2011
Bought a new DIR-655 Rev B a few weeks ago.It's web admin interface has failed in some way. The device is still passing all user traffic in both directions, but attempts to connect to the admin interface with my web browser, from both the wired inside and the WAN outside fail. I can telnet to the actual tcp port number that it's configured for and establish a connection, but I can't get any response from it. At this point I'm expecting the only way I'm going to clear the condition is to power cycle the device when I get home from work. It is to note I have the device configured for https for the admin interface. Perhaps that's the more 'advanced' feature that's newer and is exhibiting some kind of bug, I wonder. I'm running the latest firmware available from D-Link.
View 5 Replies
ADVERTISEMENT
Dec 4, 2012
I finally managed to set up this DSL modem / router on Sunday to replace my old Billion router. I set it up with DHCP and running on IP 192.168.1.254.Last night, the power tripped, and when everything came up again the entire network was dead - PC's were not getting IP's from DHCP.I connected a known working cable directly from laptop to router and attempted to access 192.168.1.254, nothing.So I reset the router and try again to the default IP 192.168.1.1. Nothing. Tried another PC, nothing.Restart router, try again, nothing. Plugged into my other router and try again, nothing. When I initially got the router I had the same problem until one day it just worked, still no idea why
View 2 Replies
View Related
Oct 25, 2012
I am trying to troubleshoot my new design as you can find it in the attached file, the setting of the up-link interfaces as below:
View 6 Replies
View Related
Nov 11, 2011
Went to log into the web admin interface on my SG-300 today and I get this in both IE and Firefox:
I'm not able to login by typing user/password and just pressing enter. I've tried power-cycling the switch, however, since the power cycle, the font-panel system LED has been blinking green. I seem to recall, though I can't locate the reference now, that this means the switch is running with factory settings, but that cannot be right because:
1. I had previously saved a new configuration on the switch, which it should be using now.
2. It is answering on the configured non-factory IP address -- just not rendering the web admin interface successfully.
I've had this unit for approximately a month. This is not the first issue I have had with this unit (see: [URL] and I'm experiencing some strange LAN speed issues since I installed it. Do I need to RMA this thing?
View 1 Replies
View Related
Mar 6, 2013
I took one and a half hours to get everything set up, I've got a PPoE connection, my problem is that ever since I entered the administration interface each and every page takes 2-5 minutes to load, it's absurdly slow, also, when trying to setup my WiFi, it timed out several times, I updated the router to the latest firmware, the same issue, it took me 4-5 retries to get WiFi set up properly. Sometimes navigating from page to page is quicker, 30-40seconds, but still those are some big times.
Is this normal behavior or do I have a hardware problem and I need to take it back and request a new one?
Mention: I am wired from a laptop, all the lights are blue, blinking nicely.
View 9 Replies
View Related
Feb 28, 2013
I have a AIR-LAP1131AG-A-K9 this Ap is registered but, i cant enabling admin status on interface B/g, when select option throws a error. "Error in Enabling Admin Status"
View 4 Replies
View Related
Feb 16, 2012
I was unable to access the web admin on my WRT160n v3 w/ latest firmware this morning. Reset config to defaults & was able to get in. Enabled HTTPS access & disabled HTTP access & was right back where I started; reset to defaults again & left both boxes checked. Can access via HTTP, but HTTPS requests get refused/reset.
The reason I needed access was that when I booted up my laptop this morning, my wireless card wasn't picking up an IP address via WIFI, only worked via ethernet, so I need to see what was going on there — several reboots of the router didn't fix, nor has it fixed the HTTPS access problem described above.
View 6 Replies
View Related
Jan 10, 2013
How can I change the language of the admin interface on a belkin wireless router (F7D2401) it all appears dutch.
View 2 Replies
View Related
Oct 12, 2011
how to totaly disable Admin/ASDM access on our public interface of our 5510. I don't want to change IPSec or SSL access to the outside interface. Just totaly disable access to Admin/ASDM from the outside without halting all other access.
View 3 Replies
View Related
Jul 10, 2012
i have WLC 5508 showing the below Logs , which prevent the users from connecting to the SSIDs , also its disconnecting the associted users DHCP Socket Task: Jul 11 09:54:08.992: %SIM-3-DHCP_SERVER_NO_REPLY: sim_interface.c:1039 Failed to get DHCP response on interface 'interface-02'. Marking interface dirty.*mmListen: Jul 11 09:54:08.638: %MM-3-INVALID_PKT_RECVD: mm_listen.c:7671 Received an invalid packet from 10.21.1.25. Source member:0.0.0.0. source member unknown.it shows 3 to 4 times durring 1 hour ,
View 2 Replies
View Related
Jul 22, 2012
having a bit of trouble setting up our 5510. None of us have ever played with a firewall before. We've got most of the basics covered. I was able to get to the outside world to do a software update to the box, but my laptop that sits in the inside can't see the outside. We only have the default access rules in place at the moment. Our old ISA firewall rules don't really translate all that well to this new box.
View 2 Replies
View Related
Mar 9, 2011
I have ASA 5510 with 8.3 version and using multi context. I created a new context ABC and tryed to add routes in the context for the ABC networks it would not work. There was an error in the log stating, “failed to locate egress interface”. I changed the metric on the static routes from 1 to 2 and it started working. Is it normal in a multi context?
View 4 Replies
View Related
Nov 25, 2012
I'm receiving this error on a WAVE-574 appliance. The primary interface is configured and I can ping between the wave and the central manager.
View 1 Replies
View Related
Apr 9, 2013
I have ASA 5505, in routed mode, basic license.I run a web server in DMZ. I can reach Internet from DMZ. Also, the trafic from outside can reach the web server. However, if the web site is requested from within the DMZ, the request will fail, and the firewall log contains the following message:
Failed to locate egress interface for TCP from DMZ50: 30.30.30.10/49213 to 170.70.30.114/80
I don't have DNS, so the request must go to Internet, even the web site is hosted on the server in DMZ.
Here is sample of my config file:
interface Vlan1
nameif inside
security-level 100
ip address 162.160.1.3 255.255.255.0
!
interface Vlan2
[code]....
What can be the reason for requests, originated in DMZ, to fail, and how could it be fixed?
View 1 Replies
View Related
Oct 30, 2011
I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout. Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem. Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.
View 5 Replies
View Related
Dec 12, 2012
I have a DLink N300 (DIR 615), firmware 9.02NA.I've been trying to log into the "admin" but was only able to once. When I did get it everything was greyed out so I couldn't make any changes.
View 1 Replies
View Related
Jan 6, 2013
i'm having some trouble logging in as admin. I leave the password section blank as directed but it comes up as "incorrect password". I then tried the same using the "User" and it worked just fine but i cant change any of my settings.
View 6 Replies
View Related
Jan 28, 2012
I just bought the Dir-655 with 2.00 firmware. I am having trouble with my NAT on my game system and I have tried everything but I have everything setup on my router where it needs to be. I read somewhere, where a guy was having my same trouble and he upgraded his firmware to 2.03na. I have tried with no success whatsoever.
Downloading the file from the d-link website with no problems. But i keep getting the same message when i try to upgrade the router saying the file may be corrupt, the router is to busy, or I am not logged in as an Admin. I am the only one using the internet and I am logged into my router as the admin. it wont even start uploading the firmware to my router..
View 9 Replies
View Related
Feb 19, 2013
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
View 1 Replies
View Related
Apr 13, 2012
Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)
View 3 Replies
View Related
Mar 12, 2013
I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w
View 1 Replies
View Related
Apr 5, 2011
I have a dir-655 a3 router that is blocking my website ip address.I could previously access this site until one day, without changing any router settings, it started blocking communication to my website. pings, tracerts, web browsers, everything simply times out. It resolves the IP address ok but doesn't go any further than that. I was on firmware 1.31 and have now upgraded to 1.35NA, but no luck. I have also tried resetting factory defaults to no avail. If i bypass the router and plug my computer straight into the modem, the site loads fine. so its definitely the router. I have tried this on a number of devices to make sure. It appears that for some reason the router is blocking that specific IP address as it is on a shared hosting and I can't access any other sites on the same IP address. Does the router check the IP address with any web service before returning the request?
View 4 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Dec 7, 2009
I am having issues with my freinds new DIR-825 Rev:B1 Firmware:2.02NA, The admin pages are intermittently slow to load and sometimes wont load until I power cycle the device. I am using IE8 on vista x64, and have the issue on all pc's on the network. Is there a work around for this?
View 7 Replies
View Related
Feb 26, 2013
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
View 4 Replies
View Related
Mar 19, 2011
I can however connect to internet ?
Tried Explorer & Firefox
View 1 Replies
View Related
Nov 30, 2011
I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522
View 3 Replies
View Related
May 16, 2010
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password
newpassword
confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
View 4 Replies
View Related
Feb 28, 2011
For about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.
Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:
I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.
All I want to do is just port forward my game servers again without the use of Hamachi or other programs
View 2 Replies
View Related
Nov 21, 2012
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
View 4 Replies
View Related
Apr 6, 2013
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I have a question regarding the admin page on the router. Default it seems to accept only http access and I cannot find the option to switch this to ssl over https. Now the admin password goes across the WLAN in clear text which is not secure and not what I want. Is there any way to change the setting so the page is only accessible through https?
View 1 Replies
View Related
Oct 16, 2011
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
View 9 Replies
View Related
Jun 24, 2011
I have problem with my system. my system is Windows 7 STARTER. When i am using internet, every time the message is showing "Link to Broad Band connection failed - reconnect pending............" like that message is comming.
View 2 Replies
View Related
