D-Link DIR-601 :: Unable To Get WAN Admin Access?
Apr 13, 2012
Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)
View 3 Replies
ADVERTISEMENT
May 22, 2012
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies
View Related
Jan 18, 2013
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
View 3 Replies
View Related
May 3, 2012
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
View 1 Replies
View Related
Feb 26, 2013
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
View 4 Replies
View Related
Mar 19, 2011
I can however connect to internet ?
Tried Explorer & Firefox
View 1 Replies
View Related
Nov 30, 2011
I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522
View 3 Replies
View Related
Nov 21, 2012
Region : NewZealand
Model : TD-W8960N
Hardware Version : V3
Firmware Version : 1.4.0 Build 111130 Rel.56405n
ISP :
Just installed my new 8960 and it's working fine. However, I'd like to disable admin access from wireless, and only have that available via the LAN. I can't find anything that looks like it'll do that in any of the setup pages, is it possible? All previous wireless routers I've had have been able to do this.
View 4 Replies
View Related
Oct 16, 2011
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
View 9 Replies
View Related
Dec 13, 2012
Unable to access router admin page for Haier model R800
View 1 Replies
View Related
May 13, 2013
Region : UnitedStates
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.1
ISP : T2
I have a problem with my tp-link router. I dont have an internet access of the router, updated firmware... When i connect to router by laptop the internet works fine, but when i connect to router by phone i have an internet access only 5 second and than i lost it, but still connected. I don't know what is the problem here, maybe phone?
View 3 Replies
View Related
Oct 18, 2012
I just got back from being gone for a couple weeks and my router stopped working. I tried to reset the router and connect to the admin screen at 192.168.1.1, but it gives a "page not found" error. My internet work with a wired connection to the router, and the computer's IP address is 66.xxx.xxx.xxx. Looking at most forums which talk about this problem it seems like most people have IP addresses starting with 192. Why does mine start with 66? Is this related to the problem of being unable to access the admin screen? This is a home network and I'm running Ubuntu and have a Linksys WRT54G router. I get the same IP address whether I connect just from the modem to the PC, or from modem to router to PC.
View 3 Replies
View Related
Jan 6, 2011
I just purchased a WAP4410N A V02 and am unable to logon using the default credentials (admin/admin). Using the default IP, 192.168.1.245, I can get to the login page, I simply cannont log in.power reset the WAPheld the reset button for 30 seconds while powered on then power reset the WAPheld the reset button on for 30 seconds while powered on, powered off the WAP for 30 seconds then powered the WAP back ontried using admin and blank as the usernametried using admin, password and blank for the password All without success.
View 1 Replies
View Related
Jan 8, 2012
I recently installed a WAP4410N for a customer without any problem, but a few days later I received a call requesting assistance as the customer could not login to the web admin page.
The login screen was showing, but it wasn't acceptingthe username and password that I had set. Today I visited customer to investigate.
I discovered that I could login without any problem using my Windows laptop, but that customer could not use any of their Apple MACs to login.
Apart from one Windows PC, all customer computers were Apple OS. Customer could login using their Windows PC without any problem.
View 2 Replies
View Related
Oct 24, 2011
This is an odd one, possibly a broken unit but I have a SRW2024P which has been running for a couple of years all OK but some time ago I noticed I couldn't access the web interface. I decided to leave it until I actually needed to change something, which is now!
After much messing around modifying a null-modem cable to work (i.e. connected pins 2,3 and 5) I managed to connect to the console through HyperTerm. Did a full factory re-set and XMoDem'd the 1.2.9 software on again but still no luck.
I tried accessing the web console and telnet with the default IP and tried setting my own IP but can't even ping them.
There are a few other peculiarities: The units MAC address in the console is shown as 00-00-00-00-00-00The units hardware version is blank in the consoleBoth PING and TRACERT tests fail to any address except the units ownTFTP uploads fail to connect (the TFTP server doesn't even log an access attempt)All other clients connected to the switch are working fine and the port statuses in the console show working connections Basically; it is as if the web/config/admin 'module' is disconnected from the actual switch in some way?
View 6 Replies
View Related
May 25, 2012
More that a year ago, with guidance from D-Link Customer Service, I performed setup on a system consisting of a DSL-2640B (with wireless disabled) and a DAP-1522 as an access point. I included the 1522 so as to have an N network, since the 2640 is G. The system works fine and I'm able to stream via the 1522 to an N 300 USB Adapter. Internet access is fine, and I'm able to access the 2640 with no problem.I want to add another 300 in a different location. To do that, I'll need to access the 1522 from my Windows 7 computer, since I've lost the passphrase that I'll need for the 300.Everything that I've read tells me to connect the 1522 directly to my computer via cable and to temporarily change the network adapter settinge to:
IP = 192.168.0.x various sources list values of 2 and 99 for x
Subnet mask = 255.255.255.0
Gateway = 192.168.0.50
Then to use a browser window to go to 192.168.0.50 Regardless of the settings that I use, the browser (IE9) always indicates that it can't connect with that address. accessing the 1522, or on any alternative way to obtain the passphrase.
View 3 Replies
View Related
Feb 5, 2012
I've installed aDIR655 for my friend's cafe and found that Clients ( both wired and WIFI ) have difficulties accessing Yahoo and MSN while Googles etc ( and other Newspaper and webmail sites are OK ) is fine.....I tried to reload and reboot and re-config etc but all in vain...
View 1 Replies
View Related
Oct 30, 2011
I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout. Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem. Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.
View 5 Replies
View Related
Dec 12, 2012
I have a DLink N300 (DIR 615), firmware 9.02NA.I've been trying to log into the "admin" but was only able to once. When I did get it everything was greyed out so I couldn't make any changes.
View 1 Replies
View Related
Jan 6, 2013
i'm having some trouble logging in as admin. I leave the password section blank as directed but it comes up as "incorrect password". I then tried the same using the "User" and it worked just fine but i cant change any of my settings.
View 6 Replies
View Related
Jan 28, 2012
I just bought the Dir-655 with 2.00 firmware. I am having trouble with my NAT on my game system and I have tried everything but I have everything setup on my router where it needs to be. I read somewhere, where a guy was having my same trouble and he upgraded his firmware to 2.03na. I have tried with no success whatsoever.
Downloading the file from the d-link website with no problems. But i keep getting the same message when i try to upgrade the router saying the file may be corrupt, the router is to busy, or I am not logged in as an Admin. I am the only one using the internet and I am logged into my router as the admin. it wont even start uploading the firmware to my router..
View 9 Replies
View Related
May 3, 2011
Few days ago, I updated the firmware of my router to 1.35NA and everything seemed to be working fine at first. After a while though, I noticed my Nexus One phone wasn't getting internet through WiFi anymore. It is connected to WiFi still, and it can ping the other devices on the network but it won't connect to the web. I have a Xoom tablet connected to WiFi as well and it is getting access to the web, though it seems to drop web access from time to time too, even before the firmware update. My phone always had a connection to the web through WiFi before the update. The two PCs that have a wired connection work fine. In the router logs, I also noticed that "UPnP renew entry 255.255.255.255 <-> ... UDP timeout:0 'Teredo'" being spammed over and over since the update, which I read has something to do with IPv6?
View 14 Replies
View Related
Jul 28, 2011
I am trying to setup a DIR-601 wireless router (Hardware Version: A1 Firmware Version : 1.00NA ) with my connection from Astound.I am able to connect to the internet from the cable modem (Motorola SURFboard SB5101) but I am unable to get it to work through the router. All the lights on the router look ok.When I look at the WAN status from the router setup page I see :
WAN
Connection Type : DHCP Client
Cable Status : Connected
Network Status : Disconnected
Connection Up Time : N/A
[code]....
* I noted that the router did not show me the correct time. Is that normal ?I have even copied my laptop's MAC address but it did not work. I restarted the modem and the router a number of times but to no avail.
View 1 Replies
View Related
May 5, 2013
I recently purchased a DLink DIR-815 router to replace my aging Linksys. The router works great, except that I can't access my ISPs website, nor their IMAP server. I can access every other page on the web. If I connect direct to the modem, or through my old Linksys it's fine, but with the DLink I'm having problems. Internet is DSL using PPPoE. The net info from the status tab is:
Local address : 206.248.167.xxx
Subnet Mask : 255.255.255.255
Peer address : 206.248.154.104
Primary DNS Server : 206.248.154.22
Secondary DNS Server : 206.248.154.170
ISP web page is at 206.248.155.70, and mail server is at 206.248.188.90 I have reset the router to factory default, and setup the PPPoE, and still the same issue. I have also tried using the DMZ but no luck. ISP can't seem to figure out the issue, and points to the router configuration.
View 4 Replies
View Related
Feb 19, 2013
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
View 1 Replies
View Related
Mar 12, 2013
I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w
View 1 Replies
View Related
Apr 5, 2011
I have a dir-655 a3 router that is blocking my website ip address.I could previously access this site until one day, without changing any router settings, it started blocking communication to my website. pings, tracerts, web browsers, everything simply times out. It resolves the IP address ok but doesn't go any further than that. I was on firmware 1.31 and have now upgraded to 1.35NA, but no luck. I have also tried resetting factory defaults to no avail. If i bypass the router and plug my computer straight into the modem, the site loads fine. so its definitely the router. I have tried this on a number of devices to make sure. It appears that for some reason the router is blocking that specific IP address as it is on a shared hosting and I can't access any other sites on the same IP address. Does the router check the IP address with any web service before returning the request?
View 4 Replies
View Related
Jun 20, 2011
Bought a new DIR-655 Rev B a few weeks ago.It's web admin interface has failed in some way. The device is still passing all user traffic in both directions, but attempts to connect to the admin interface with my web browser, from both the wired inside and the WAN outside fail. I can telnet to the actual tcp port number that it's configured for and establish a connection, but I can't get any response from it. At this point I'm expecting the only way I'm going to clear the condition is to power cycle the device when I get home from work. It is to note I have the device configured for https for the admin interface. Perhaps that's the more 'advanced' feature that's newer and is exhibiting some kind of bug, I wonder. I'm running the latest firmware available from D-Link.
View 5 Replies
View Related
Dec 5, 2012
Region : UnitedStates
Model : TL-WR702N
Hardware Version : V1
Firmware Version :
ISP : CenturyLink
I've just received my new TL-WR702N that I want to use as a repeater (downstairs) for my router (upstairs). I've tried the configurations listed on the TP-Link website, but none of them give me internet access. In fact, the local area connection shows the TL-WR702N as an "unidentified network".
View 2 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Dec 7, 2009
I am having issues with my freinds new DIR-825 Rev:B1 Firmware:2.02NA, The admin pages are intermittently slow to load and sometimes wont load until I power cycle the device. I am using IE8 on vista x64, and have the issue on all pc's on the network. Is there a work around for this?
View 7 Replies
View Related
Jul 3, 2012
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
View 1 Replies
View Related
May 16, 2010
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password
newpassword
confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
View 4 Replies
View Related
