Cisco Wireless :: WAP4401 Unable To Log On To Web Admin
Jan 6, 2011
I just purchased a WAP4410N A V02 and am unable to logon using the default credentials (admin/admin). Using the default IP, 192.168.1.245, I can get to the login page, I simply cannont log in.power reset the WAPheld the reset button for 30 seconds while powered on then power reset the WAPheld the reset button on for 30 seconds while powered on, powered off the WAP for 30 seconds then powered the WAP back ontried using admin and blank as the usernametried using admin, password and blank for the password All without success.
View 1 Replies
ADVERTISEMENT
Jan 8, 2012
I recently installed a WAP4410N for a customer without any problem, but a few days later I received a call requesting assistance as the customer could not login to the web admin page.
The login screen was showing, but it wasn't acceptingthe username and password that I had set. Today I visited customer to investigate.
I discovered that I could login without any problem using my Windows laptop, but that customer could not use any of their Apple MACs to login.
Apart from one Windows PC, all customer computers were Apple OS. Customer could login using their Windows PC without any problem.
View 2 Replies
View Related
May 3, 2012
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
View 1 Replies
View Related
Apr 13, 2012
Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)
View 3 Replies
View Related
Oct 18, 2012
I just got back from being gone for a couple weeks and my router stopped working. I tried to reset the router and connect to the admin screen at 192.168.1.1, but it gives a "page not found" error. My internet work with a wired connection to the router, and the computer's IP address is 66.xxx.xxx.xxx. Looking at most forums which talk about this problem it seems like most people have IP addresses starting with 192. Why does mine start with 66? Is this related to the problem of being unable to access the admin screen? This is a home network and I'm running Ubuntu and have a Linksys WRT54G router. I get the same IP address whether I connect just from the modem to the PC, or from modem to router to PC.
View 3 Replies
View Related
Jan 18, 2013
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
View 3 Replies
View Related
Oct 24, 2011
This is an odd one, possibly a broken unit but I have a SRW2024P which has been running for a couple of years all OK but some time ago I noticed I couldn't access the web interface. I decided to leave it until I actually needed to change something, which is now!
After much messing around modifying a null-modem cable to work (i.e. connected pins 2,3 and 5) I managed to connect to the console through HyperTerm. Did a full factory re-set and XMoDem'd the 1.2.9 software on again but still no luck.
I tried accessing the web console and telnet with the default IP and tried setting my own IP but can't even ping them.
There are a few other peculiarities: The units MAC address in the console is shown as 00-00-00-00-00-00The units hardware version is blank in the consoleBoth PING and TRACERT tests fail to any address except the units ownTFTP uploads fail to connect (the TFTP server doesn't even log an access attempt)All other clients connected to the switch are working fine and the port statuses in the console show working connections Basically; it is as if the web/config/admin 'module' is disconnected from the actual switch in some way?
View 6 Replies
View Related
May 22, 2012
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies
View Related
Dec 13, 2012
Unable to access router admin page for Haier model R800
View 1 Replies
View Related
Apr 21, 2011
How to shut off wireless admin access on a 1131 AP? I only want to be able to administer the device via the wired LAN. I need to shut of http, ssh, and telnet.
I haven't been able to find anything in the GUI.
How to know the CLI commands?
View 6 Replies
View Related
Feb 13, 2011
I'm having an issue with our WAP2000 access point. I had to reset the access point and now I can't access the admin console. I've set a static IP address just as I did when I first set it up. Now when I browse to the 192.168.1.245 in my browser it just displays an Authentication error.
View 1 Replies
View Related
Aug 20, 2012
We have 1242-AG series AP which is configured in Rogue Detector mode. After adding this AP to WLC its showing Admin Status of AP as Down.
When i am trying to enable the Admin Status its giving me following error
" Admin status cannot be enabled for AP in Rogue Detector mode".
how to enable Admin Status for Rogue Detector AP.
View 4 Replies
View Related
Sep 18, 2012
I have a E4200 router(firm 1.0.14), which was acting strange, so I reset it.(Windows PC's were hacked with Bluetooth RAT) I did a 30-30-30 reset, and flashed v1.0.14 firmware again.
Presently, I'm using Ubuntu Linux 12.04 LTS, to access Setup(Admin) via computer. After changing to a strong password to access the Admin, I setup everything, as it appeared, [when I used Cisco home network app in Windows, then went in and wrote everything down, in a (paper)notebook], that I keep locked in the safe.
Next, I set the SSID as JCs Gate, expecting JCs Gate & JCs Gate-Guest to appear wireless, after setting up WPA2 security(for both bands), and turning on guest AP and limiting it to 3 as not many use it. After saving and rebooting the router, I am still seeing Cisco23540 as my SSID, and I prefer not to broadcast my router make, as I've reported the neighborhood kid(to his father), after several hacking attempts, from his MAC addy(which I know because I see it in the logs, and sold them the PC custom built) and want to get Cisco out of the SSID.
I'm a hardware IT tech pro, with a MCSE cert, so I'm not a stranger to router setups, after 15+ years in the biz. Either, I'm missing something or going crazy. BTW for about 1hour both JCs Gate and Cisco 23540 were both broadcasting.
View 3 Replies
View Related
Feb 4, 2012
We have a fast broadband service and three teenagers, two of which have laptopsWe are allowed 100Gb/month; if we exceed that, the we are charged $1.5/Mb. The provider has a web interface where we can check the last 24hours' usage. When ever we go over the daily budget, I ask the darling children who was watching all the videos-- to which they all say "not me".I want a wireless router with some admin features that allow me to see real-time who is the bandwith pig and shut them doI am not aware of any routers in the $100-$150 range that have these kind of features. There are industrial grade Cisco routers, but these have more features than I need and are really expensive
View 2 Replies
View Related
Oct 21, 2012
1552 E Ap with a 2504 WLC. Single Root Ap with Mesh the Mesh has the problem. Both Power Injector and AP has been replaced . How do you turn on the 802.11 B Radio? No other problems at 40 other sites with identical installation.
View 1 Replies
View Related
Feb 28, 2013
I have a AIR-LAP1131AG-A-K9 this Ap is registered but, i cant enabling admin status on interface B/g, when select option throws a error. "Error in Enabling Admin Status"
View 4 Replies
View Related
Sep 3, 2011
How do I find the security key for admin-pc network, when i type the one i have it comes up as mismatched.
View 1 Replies
View Related
May 7, 2012
I need to get to my web admin page, but I cannot get into my router to do so.IE tells mt that there is a certifacte error, and then gives me the option of going in anyway.When I select that option, nothing happens, and the same IE warning page remains.I am plugged directly into an e-net port on the router, and it is a WRT160N.
View 1 Replies
View Related
Apr 25, 2012
I tried all methods: Cisco Connect (on Vista), http and https, but none works. However, the router seems function correctly. My laptop can acquire DHCP address and browse via the router. But I just cannot connect to the router to perform Admin tasks.Problem: when I launch CiscoConnect: the GUI shows "Cannot access your router", even though I am using the router to browse the net wirelessly and wirely. Using browser to navigate to http://192.168.1.1 and https://192.168.1.1 also give me cannot access error!
View 1 Replies
View Related
Aug 3, 2010
After flashing the latest version of the firmware for the WRV200 (1.0.39) all of the pages on the web based admin tool are not working, and some are missing alltogether.I need to be able to re-flash the firmware to an earlier version (or attempt to re-flash this version) without using the web-based admin tool, as the page for doing the flash is one of the one's that is missing. Re-setting it doesn't work. I have tried searching here and through Google without any luck so far. The WRV200 works fine, but obviously is not locked down from a security standpoint, which is a large problem.
View 5 Replies
View Related
Mar 13, 2013
Deployed two Cisco ISE 1.1.3. ISE will be used to authenticate wireless users, admin access to WLC and switches. Backend database is Microsoft AD running on Windows Server 2012. Existing Cisco ACS 4.2 still running and authenticating users. There are two Cisco WLCs version 7.2.111.3.Wireless users authenticates to AD through ACS 4.2 works. Admin access to WLC and switches to AD through ISE works. Wireless authentication using PEAP-MSCHAPv2 and admin access wtih PAP/ASCII.
Wireless users cannot authenticate to AD through ISE. The below is the error message "11051 RADIUS packet contains invalid state attribute" & "24444 Active Directory operation has failed because of an unspecified error in the ISE".Conducted a detailed test of AD from ISE. The test was successful and the output seems all right except for the below: [code]
Update:
1) Built another Cisco ISE 1.1.3 sever in another datacentre that uses the same domain but different domain controller. Thais domain controller is running Windows Server 2008. This works and authentication successful.
2) My colleague tested out in a lab environment of Cisco ISE 1.1.2 with Windows Server 2012. He got the same problem as described.
View 6 Replies
View Related
Feb 14, 2013
I have two 5508 WLCs. Both have APs attached to them. If I create a guest account with the lobby administrator on one, will that user account be able to log in to the network if the client is attached to the ohter WLC? So far, I have found that I need to create the same user on both WLC's, in order to have the user login.
View 2 Replies
View Related
Dec 27, 2012
I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"
View 3 Replies
View Related
Jul 8, 2011
I just got a WRV 210 wireless router (three of them actually, planning to set up a VPN). But I can't set the admin password. I've tried 4 times, and every time, i've got to hold the reset button to reset to factory settings in order to access the management pages! I enter the new password in both fields, and then click to save the settings. It restarts. Then i try to log in - and it doesn't accept the new password. It doesn't accept the default password. I've tried with admin/(new password) and (new password)/(new password), and admin/admin. None of them work, forcing me to reset router to factory settings. I've tried a password composed of 6 letters followed by a . Thinking that maybe the . was throwing it off, I tried 6 letters followed by 3 numbers. That doesn't work either. I've updated to firmware version 2.0.1.5. No luck.
View 1 Replies
View Related
Feb 23, 2012
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
View 1 Replies
View Related
Dec 18, 2011
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1:
Not shown: 65531 closed ports
PORT STATE SERVICE
139/tcp open netbios-ssn
443/tcp open https
445/tcp open microsoft-ds
1780/tcp open unknown
View 2 Replies
View Related
Aug 11, 2012
As I've seen in my Linksys' admin panel, I have a log option (Administration/Log). So if I enabled it i can check which sites was browsed in my home network?And the second question: if Linksys can store the browsed sites history and if I will use a VPN connection on my PC or iPhone (not router!) the logs will be still look like before setting-up VPN on PC? So like: [URL] not like: [URL]?
View 3 Replies
View Related
Mar 6, 2013
I took one and a half hours to get everything set up, I've got a PPoE connection, my problem is that ever since I entered the administration interface each and every page takes 2-5 minutes to load, it's absurdly slow, also, when trying to setup my WiFi, it timed out several times, I updated the router to the latest firmware, the same issue, it took me 4-5 retries to get WiFi set up properly. Sometimes navigating from page to page is quicker, 30-40seconds, but still those are some big times.
Is this normal behavior or do I have a hardware problem and I need to take it back and request a new one?
Mention: I am wired from a laptop, all the lights are blue, blinking nicely.
View 9 Replies
View Related
Apr 17, 2012
how to change username admin to something different. I can reset the router password but there's no easily identifiable option for changing the username.
View 5 Replies
View Related
Sep 29, 2011
I have an E1000 linksys router. I am trying to determine the admin password. I have looked at seeral entries regarding this. I do not have CICSO connect installed. Not sure why. The router works fine. I have the CD that came with the router. I have also downloaded current version of connect software. Both of them want to config the router. The first item asked for is the admin password. I know I press reset button. I am trying to retrieve password without doing that.
View 1 Replies
View Related
Jun 9, 2012
I have logged into the admin area 192.168.... And I do not see where to change the SSID.
View 2 Replies
View Related
Jan 5, 2012
I have the WRT160N router for 3.5 yrs and it's worked perfectly since installing it. About two weeks ago it began intermittently dropping cable connection. First few times I thought I could resolve it by unplugging/plugging router & modem so they can "re-syn" to the cable connection. That still works but now it occurs sometimes multiple times within a few minutes/hours and then won't happen again for an entire day/days. The other day I had connectivity but instead of the usual 5 bars I only had 3 while using my laptop in the same spot in the house as usual.
View 5 Replies
View Related
Feb 3, 2013
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
View 9 Replies
View Related
