I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"
Moved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
I'm trying to install an Engenius EAP9550, configured as a wireless repeater. the instructions are beyond abominable (as the review on Amazon warned). They tell me to enter 192.168.1.1 (which is my linksys E2000 wireless routers address, though they say nothing about that) and tehn give me no other information on how to configure or set this up.
I'm having trouble setting up my WAP 4410n. I can connect to it wirelessly, I can ping it, but somehow when I try to connect to the admin intervace (in my case 192.168.1.36) I get the following error message:
"The connection was reset. The connection to the server was reset while the page was loading"
My I shut down my firewall, restarted my router, removed cookies and cleaned cache, but that's as far as my knowledge goes.
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
I'm using my 655 as a WAP, so nothing is connected to the WAN port. Since I run a SBS2008 in my home, I also have the 655's DHCP disabled.If I enable Network Filtering, everything inbound/outbound on the LAN ports works except accessing the Admin page. Even if I put the connecting PC's LAN MAC in the tablet.
We have an SLM248G switch which seems to be giving a few problems. When attempting to access the switch, the admin page loads but after logging-in, the admin portal page does not load fully, see screenshot.
Even after a factory reset (reset button held), the issue continues. Is there any other workaround for completely resetting everything?
I recently am trying to get an open nat type so I can play Playstation network better. I watched a video and they told me to turn off the NAT and I did now it does not let me connect to the router page now, I can connect to the internet and stuff but I can't connect to the router page
I don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
I recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1: Not shown: 65531 closed ports PORT STATE SERVICE 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 1780/tcp open unknown
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
Region : Netherlands Model : TL-WDR4300 Hardware Version : V1 Firmware Version : ISP :
I have a question regarding the admin page on the router. Default it seems to accept only http access and I cannot find the option to switch this to ssl over https. Now the admin password goes across the WLAN in clear text which is not secure and not what I want. Is there any way to change the setting so the page is only accessible through https?
I am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout. Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem. Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
I have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
Is there a way to put a login banner on the ACS admin web page? Either display it directly on the web page or do a redirect to a banner page? Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
For about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.
Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:
I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.
All I want to do is just port forward my game servers again without the use of Hamachi or other programs
I recently replaced my RV042 with an RV042G. I did an export of the RV042 Config and used the Config Migration Tool to upgrade the file to v3 (I had an old v1 RV042). When I first logged in to the RV042G it was quite happy and I imported the config file successfully.After installing the RV042G in my system it fired up and worked perfectly. Unfortunately when I now try to log in via the web interface it comes up with 'Invalid Site Certificate' each time. I've tried importing the certificate but that does not work as it is flagged as invalid.All I can assume is I have either imported the origional RV042 certificate as part of the config or importing the config has corrupted the original RV042G site certificate. I assume this is a generic issue and not specific to the RV042G as I have had this problem before but cannot remember how I solved it.The bottom line would be a hard reset and load all my settings manually but I can't spare the time just now.
I can access the website in other places(such as my library, another house, my university, my towns book store, etc.) but not at my own house. I can access the website anywhere but my own home! I contacted my ISP provider and he said that the website was not blocked by the ISP provider because the ISP consultant was able to access the website .I know the problem isn't rooted in my computer and believe that the problem is IP related because I was not able to access the website on either of the three computers at my house.
My computer won't connect to any of Google's servers. ANY of them. Gmail, docs, reader, nothin. I can visit youtube, but I cannot get to the log-in page. EVERY other site works pretty well. Heck, even using a site that uses a Recaptcha it doesn't load the recaptcha!Nothing wrong with my hosts file.
Tracert results in 6 successful hops and then times out (I think at my ISP?) the last 2 successful hops are chnddsrj01-ae2.0.rd.ph.cox.net And then langbprj02-ae2.rd.la.cox.net Then all time outs
My other PC is connected to the SAME wifi network right now, and I'm posting from it, and it works fine. Both are on XP. Reboots haven't worked. Happens on all browsers. Every other website I can find is just fine.
I have a little problem with installing my new router. There were quite a lot of problems with the old smc, so I've bought a TP-Link router. I installed it just alright, it said congratulations, you have internet. I don't have though, not even on the directly plugged computer. It's kind of frustrating, since the old router is still working like before. So I plugged an ethernet cable from the old router's lan to the tp-link wan and with that, the new network is working just fine. The problem with the internet access occurs only, if the router is directly plugged to the modem. (The computers do find the network but the connection is kind of offline.) I don't really know what could be the problem, since I'm a little new to routers. I've read almost everything in the new router's manual and I'm pretty sure it's installed correctly. (ADSL username and password copied from the old settings, mac address copied, all ip addresses pinged, done power cycle etc..) I thought about resetting the modem, but I'm a bit afraid of losing the old router's internet connection as well.