Is there a way to put a login banner on the ACS admin web page? Either display it directly on the web page or do a redirect to a banner page? Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
We are using ACS 5.3 running on VMWare.
I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.
View 9 Replies View RelatedI recently replaced my RV042 with an RV042G. I did an export of the RV042 Config and used the Config Migration Tool to upgrade the file to v3 (I had an old v1 RV042). When I first logged in to the RV042G it was quite happy and I imported the config file successfully.After installing the RV042G in my system it fired up and worked perfectly. Unfortunately when I now try to log in via the web interface it comes up with 'Invalid Site Certificate' each time. I've tried importing the certificate but that does not work as it is flagged as invalid.All I can assume is I have either imported the origional RV042 certificate as part of the config or importing the config has corrupted the original RV042G site certificate. I assume this is a generic issue and not specific to the RV042G as I have had this problem before but cannot remember how I solved it.The bottom line would be a hard reset and load all my settings manually but I can't spare the time just now.
View 2 Replies View RelatedI am trying to log into my WRT610N version 2.0 Router admin page 192.168.1.1 using the secure HTTPS://192.168.1.1 protocol I have the router local management setting to allow both http and https access login:192.168.1.1/Management.asp I am using Microsoft IE version 10 and Firefox version 19.02 and latest Chrome browsers and none of them will work using the HTTPS protocol.This used to work in the past using older versions of the browsers though I would see a certicificate error warning.I have 2.00.01 build 15 firmware installed and I already tried reseting the router. Perhaps the router needs new firmware update to handle this with the latest browsers?
View 6 Replies View RelatedI'm having trouble with a Cisco Catalyst 2950 Series Switch where by I'm following the procedure from Cisco's web site to remove the Banner and login information, url..
Each command is being accepted by the switch from following the information given within the help sheet above,the problem i have now is when i turn the power off then turn the switch back on I'm still getting the banner and login information even though i have follwed Cisco's help correctly.
I'm experiencing some problems with AAA authentication banners and banner logins.I'm trying to use spaces and empty lines, but when login, all the lines are after each other, no empty lines, no spaces.The problem appears on a 3750 with IOS version 12.2(5)SE2.
View 5 Replies View RelatedI have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.
I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.
I have installed LMS4.2.2 on Windows 2008 server and am unable to login via the 'admin' username. I get "Invalid Username or Password. Please try again" error message. I can successfully login using Windows AD username and password.
I have reset the password for 'admin' username with the following:
!
nmsrootinperl.exe resetpasswd.pl admin
Server has been rebooted PRE and POST password reset.
i'm having some trouble logging in as admin. I leave the password section blank as directed but it comes up as "incorrect password". I then tried the same using the "User" and it worked just fine but i cant change any of my settings.
View 6 Replies View RelatedI followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout. Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem. Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.
View 5 Replies View RelatedI wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w
View 1 Replies View RelatedMoved into a new place, set up a connection. Server provider gives only one mac address, they set it on my router. They say that it should be working, make a restart and that's it. I did that but still no connection. Moreover, I cannot connect through the router at all and therefore cannot access router admin page to configure it either. Now what to do? Password for the router is correct. Even when I take down all the security, still I cannot connect.To be more specific, at first I could enter the router admin page, but since I didn't know how to configure it properly, I made some mistake. I think I choose setting "configure wireless network" and changed something there. After that I cannot access the admin page or connect through the router.
View 1 Replies View RelatedI have a binatone wi-fi modem. Internet is working good from router but i am not able to connect to router admin page i.e 192.168.1.1 and not be able to change wi-fi password.
View 3 Replies View RelatedI'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
View 1 Replies View RelatedI'm having trouble setting up my WAP 4410n. I can connect to it wirelessly, I can ping it, but somehow when I try to connect to the admin intervace (in my case 192.168.1.36) I get the following error message:
"The connection was reset. The connection to the server was reset while the page was loading"
My I shut down my firewall, restarted my router, removed cookies and cleaned cache, but that's as far as my knowledge goes.
My organization has deployed 3 Cisco RV042 (v3) at our 3 sites. They have been working pretty well up until about a week ago. One of them continues to route traffic and perform port-forwarding, but the VPN has completely stopped working and I can no longer access the web administration interface. I get the standard login page, but any attempt to login (with correct or incorrect password) takes maybe 5 minutes with a spinning status icon, followed by a blank page leaving the browser at: url...
I have the router logs e-mailed to me, and I can see that the system boots up with Jan 1 2010 as the system date, but it eventually gets the correct date from NTP, so I'm doubting this is causing the problem.
These were working for months prior to this happening, and even a reboot of the affected RV042 does not allow me to log into it or setup the VPN tunnels. I have found similar threads on this forum: url...
How to access the admin page of the RV220W from an iPad wih the default security certificate? If so, what steps did you go through? Or is this only possible when purchasing a certificate?
View 10 Replies View RelatedI was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
View 3 Replies View RelatedI have this problem since updating my firmware from 1.00.12 to 1.0016 (Annex A)
Problem: After leaving the router on for 1 day(dont know exactly how many hours), I tried logging in again on the admin page 192.168.1.1. Auth box appears, put username & password, but blank page after that. Tried using Safari/Firefox and it's the same. Router is working, all the LED lights are good, Internet is working, DHCP and all other config is normal. It's just that I can't access the admin page anymore.
When I power on/off the device, the problem is gone. Admin page is accessible again. But after some number of hours again, same problem blank admin page.
Does it has something to do with the router config like g.dmt/dsl 2 ?
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
View 1 Replies View RelatedMotorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
View 3 Replies View RelatedFor about a month or two now, I've not been able to connect to my router's admin page @ 192.168.1.1 I am using a D-Link DSL-2680 router.
Whenever I go to connect to 192.168.1.1 in my Web Browser, it just sits there trying to connect and does nothing. But eventually after some minutes I get the error: 'This web page is not available The web page at http://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 101 (net::ERR_CONNECTION_RESET): Unknown error.' Here is a screenshot:
I tried pressing the reset button on the back of my router, but it would just sit there with the green power LED and another green LED just flashing constantly (I assume this is the ethernet 1 cable LED) and this happens for more than 10 minutes.
All I want to do is just port forward my game servers again without the use of Hamachi or other programs
I have two wireless repeaters and can no longer access their set-up / admin page via default IP 192.168.10.1,I don't know the brand of the repeaters, which are commonly sold on eBay. Here's one example: eBay Item # 300829809133, They work well as repeaters, but it's frustrating that I can no longer access their set-up / admin page via default IP 192.168.10.1. Right now I have only one repeater plugged in and connected to my laptop via ethernet cable. The 2nd repeater is unplugged. The Wifi on my laptop is switched off and disabled, so I'm actually connected to the Internet via my laptop's ethernet port via ethernet cable to the repeater's ethernet port, then via wifi signal from the repeater to my Zyxel wireless router and Comcast cable modem. If I'm connected to the Internet via the repeater, why can't I access the repeater's set-up / admin page using default IP 192.168.10.1? When I enter http://192.168.10.1/ into Internet Explorer, I get only the error message "Internet Explorer cannot display the webpage"
View 3 Replies View RelatedI don't have to completely reset my router as I have a ton of configs on it. Anyway, recently for some reason, I lost all access to my admin page. Cisco Connect also cannot find the router. Funny thing is that all of my wireless profiles work just fine. Meaning all of the computers in my home connect to the internet just fine using the router. Both the guest access and WPA connected machines.[url]...
View 1 Replies View RelatedI recently tried to edit settings on my E3200 and was unable to get to the page. I typed in 192.168.1.1 in the address bar, made sure no proxies were enabled and tried on wired and wireless computers and all the times it said "page could not be displayed" i haven't not reset with the button on the back. I also did an map scan of the router and this is what came up
Interesting ports on 192.168.1.1:
Not shown: 65531 closed ports
PORT STATE SERVICE
139/tcp open netbios-ssn
443/tcp open https
445/tcp open microsoft-ds
1780/tcp open unknown
After clearing the Browser-Cache I cant get to the Home page when I login to LMS3.2. Instead of the Homepage following is showing: NOT FOUND Unable to find URL. The selected View has been deleted or Friendly URL has been modified.
View 1 Replies View RelatedWe have an SLM248G switch which seems to be giving a few problems. When attempting to access the switch, the admin page loads but after logging-in, the admin portal page does not load fully, see screenshot.
Even after a factory reset (reset button held), the issue continues. Is there any other workaround for completely resetting everything?
I have set up a second E4200 as an AP.Even though I’m getting a signal from it I can’t open the ADMIN page. Also, it’s NOT showing up on my main 4200 "DHCP client table'.I configured it as a static IP 192.168.1.145 during setup and still cannot get in. My ping to .145 comes back “timeout”!Since I’m getting a full signal from it, it must be working so why can’t I get in and why doesn't it show up?
View 7 Replies View RelatedRegion : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
I have a question regarding the admin page on the router. Default it seems to accept only http access and I cannot find the option to switch this to ssl over https. Now the admin password goes across the WLAN in clear text which is not secure and not what I want. Is there any way to change the setting so the page is only accessible through https?
I have a BEFSR41 V2 working as dial in ADSL connection.While I changed my settings of the UPnP in the router I lost access to the admin page. Well most strange is that everything is working.I kept my internet access as well as the computer and printer access.The only thing I lost is access to the router admin page.The password it was not defaulted to admin, neither kept the password that I had set up.
View 9 Replies View Relatedcustomize the login page for the ssl-vpn as mentioned. When the vpn is set up, the default template allows my customers users to login with this : IMAGE 1
While trying to edit the login page, I have to create a new Customization file from CLIENTLESS SSL VPN ACCESS -> PORTAL -> CUSTOMIZATION in the ASDM. When I do that and I try to edit the login page, it comes up with 2 forms of authentication and an internal password prompt like this: IMAGE 2
How can I edit the login page I created so that users will only see the regular username and password fields like the default template?
I have an ASA5510 that I am trying to set up for remote access using SSL VPN & clientless SSL VPN. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. I have a TAC case opened and have spoken with 4 engineers thus far. I have tried several software versions on the device and they all give the same result.When going to https://(outside interface ip address), I receive the expected ssl certificate error, then I click to continue to the website, and the browser never loads a page. I can see the ssl negotiation in my debug, and it completes that portion. My http debug shows the get requests to https://(outside interface ip address)/+CSCOE+/index.html and/or logon.html, but the page never loads.
View 7 Replies View RelatedI configured my ACS 5.1 correctly, but I get an "Access is denied to NCS" at the web login page. In the ACS i see a successful authentication.
View 14 Replies View Related