Cisco Switches :: Unable To Connect To / From Admin Module On SRW2024P
Oct 24, 2011
This is an odd one, possibly a broken unit but I have a SRW2024P which has been running for a couple of years all OK but some time ago I noticed I couldn't access the web interface. I decided to leave it until I actually needed to change something, which is now!
After much messing around modifying a null-modem cable to work (i.e. connected pins 2,3 and 5) I managed to connect to the console through HyperTerm. Did a full factory re-set and XMoDem'd the 1.2.9 software on again but still no luck.
I tried accessing the web console and telnet with the default IP and tried setting my own IP but can't even ping them.
There are a few other peculiarities: The units MAC address in the console is shown as 00-00-00-00-00-00The units hardware version is blank in the consoleBoth PING and TRACERT tests fail to any address except the units ownTFTP uploads fail to connect (the TFTP server doesn't even log an access attempt)All other clients connected to the switch are working fine and the port statuses in the console show working connections Basically; it is as if the web/config/admin 'module' is disconnected from the actual switch in some way?
I have an issue with SRW2024P-K9-BR (SG300). Datasheet and configuration guide show me that is possible configure DHCP snooping in this switches, but web interface and console don't appear related menus/commands.
I'm using firmware version 1.1.2.0 and didn't found anything about this here.
I just got back from being gone for a couple weeks and my router stopped working. I tried to reset the router and connect to the admin screen at 192.168.1.1, but it gives a "page not found" error. My internet work with a wired connection to the router, and the computer's IP address is 66.xxx.xxx.xxx. Looking at most forums which talk about this problem it seems like most people have IP addresses starting with 192. Why does mine start with 66? Is this related to the problem of being unable to access the admin screen? This is a home network and I'm running Ubuntu and have a Linksys WRT54G router. I get the same IP address whether I connect just from the modem to the PC, or from modem to router to PC.
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
We are looking forward to implement IBM BladeCentre Swiches connectivity with Nexus 2k module.I would like to brief you about my network over as follows:
Currentl Solution : we want to connect the IBM Blade Switches (4) as demonstrated in the attached diagram which will be connected to Nexus 2k module as Ether-channel Access port.
Initially we been proposed by our vendor with this design and Now vendor is recommending us to connect the Blade switch etiher to Nexus 5k switch or directly to 6513 core-switches instead of Nexus 2k modules as they say Nexus 2k modules are only to connect the Edge devices .
We do not have ports available on Nexus 5010 to connect the cables from IBM Blade Centre Switches. Otherthan that, incase if we go ahead and connect the IBM Blade switches as access ether-channel access port with Nexus 2k module what are consequences we have to face realted Spanning tree or any other.
I just purchased a WAP4410N A V02 and am unable to logon using the default credentials (admin/admin). Using the default IP, 192.168.1.245, I can get to the login page, I simply cannont log in.power reset the WAPheld the reset button for 30 seconds while powered on then power reset the WAPheld the reset button on for 30 seconds while powered on, powered off the WAP for 30 seconds then powered the WAP back ontried using admin and blank as the usernametried using admin, password and blank for the password All without success.
Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)
I am unable to connect to webview on our SRW2024 switch. I use a macpro G5 running 10.6.8. When i try to connect to it through Safari, Chrome, or Firefox using 192.168.1.254, I receive a message that a connection cannot be established. 192.168.1.254 is the ip mentioned in the manual. I used an ip scanner and it showed the actual ip is 192.168.0.1. But I cannot connect to webview through this ip either. We got this switch a year ago and did not change any settings, we just connected it and it worked fine. But now we want to change some settings on the switch but cannot connect.
Trying to connect 2 switches together (both 2960G 8 ports). I have an SFP in each (GLC-LH-SM). They are connecting over SingleMode Fibre using the correct cabling. The fibre cores have been tested and are all ok also.
I can't get no Layer 1 connectivitiy at all. Just dead. I have tried 4 different GBICS, swapped cabled etc.. I have forced the media type to use SFP. No link light....
I thought it would just be a case of plugging in the gbics cables and off I go! I read about forcing the speed and duplex on the port but because the port if SFP, the speed and duplex settings are not available. This seems to be hard coded.
I am unable to connect vivotek ip7137 camera with d link or netgear router I tried all my best made the connection with eithrnet cable , reset both machine set static ip of pc but nothing is happening?
I have an Iball Baton Router. I am not able to connect to it from my PC. However, I am able to connect to the router from my Laptop.I have tried isconnecting and renewing the ip. Can see that ip (192.168.1.102) is issued to my PC and can ping to the same. But, do not get any reply when I ping to the gateway (192.168.1.1 - ip for the router). My OS is Windows 7 64 bit.Let me know if you need any more information
I recently installed a WAP4410N for a customer without any problem, but a few days later I received a call requesting assistance as the customer could not login to the web admin page.
The login screen was showing, but it wasn't acceptingthe username and password that I had set. Today I visited customer to investigate.
I discovered that I could login without any problem using my Windows laptop, but that customer could not use any of their Apple MACs to login.
Apart from one Windows PC, all customer computers were Apple OS. Customer could login using their Windows PC without any problem.
I am trying to connect two D-link 24 port switches thru cat 6 cable, distance is less than 50 meters, but its not working but if i connecting it with a Laptop i am able to connect to the network. But if i connect the switch in between it fails i tried changing the switch and cable but no use anyone have a clue how it fails?
Went to log into the web admin interface on my SG-300 today and I get this in both IE and Firefox:
I'm not able to login by typing user/password and just pressing enter. I've tried power-cycling the switch, however, since the power cycle, the font-panel system LED has been blinking green. I seem to recall, though I can't locate the reference now, that this means the switch is running with factory settings, but that cannot be right because:
1. I had previously saved a new configuration on the switch, which it should be using now.
2. It is answering on the configured non-factory IP address -- just not rendering the web admin interface successfully.
I've had this unit for approximately a month. This is not the first issue I have had with this unit (see: [URL] and I'm experiencing some strange LAN speed issues since I installed it. Do I need to RMA this thing?
Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
what to do with my router cdr -king i cant access 192.168.1.1 in second time. i access it for the first time but i forgot to configure password now i cant connect using ID:admin Pass:admin
I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1
I have a wireless router that was named and all the wireless equipment (laptop, ipod, phones) was connecting easily with no problems. Everything is saying "unable to connect". I have no clue what she did but she said her laptop asked her for the 8 number code from the router and she entered it.
I recently purchased an SG300-10 switch. Is it possible to change the TCP port numbers for the administrative services on this device? For example, if I wanted to change the web admin port from being availble on port 80 to port 8080, or move the SSH port from 22 to 2022, how would I do this?
I've looked over the web admin interface, and the Security > TCP/UDP services option looks like what I want, but I see no way to change a service's listening port. Is this possible?
I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5. Also need to connect VPN but unable to.
Deployed two Cisco ISE 1.1.3. ISE will be used to authenticate wireless users, admin access to WLC and switches. Backend database is Microsoft AD running on Windows Server 2012. Existing Cisco ACS 4.2 still running and authenticating users. There are two Cisco WLCs version 7.2.111.3.Wireless users authenticates to AD through ACS 4.2 works. Admin access to WLC and switches to AD through ISE works. Wireless authentication using PEAP-MSCHAPv2 and admin access wtih PAP/ASCII.
Wireless users cannot authenticate to AD through ISE. The below is the error message "11051 RADIUS packet contains invalid state attribute" & "24444 Active Directory operation has failed because of an unspecified error in the ISE".Conducted a detailed test of AD from ISE. The test was successful and the output seems all right except for the below: [code]
Update:
1) Built another Cisco ISE 1.1.3 sever in another datacentre that uses the same domain but different domain controller. Thais domain controller is running Windows Server 2008. This works and authentication successful.
2) My colleague tested out in a lab environment of Cisco ISE 1.1.2 with Windows Server 2012. He got the same problem as described.
I was trying to get into my router to give it a reboot yesterday, but was unable to get into the console. I used the username/password I've used for over a year (it was also auto saved) but it would not let me in. I went through all the steps to do a hard reset/restore default settings and it wouldn't let me. I had to access the boot loader to reload firmware, and that worked out just fine.
Now, I still cannot get access to the administration console with the default username (blank) and password (admin). I've tried moving my PC to ports 1-4 and none work.
I was about to give up on the router but I tried connecting from my iPhone and everything works just fine. I was even able to change my SSID and WPA key again.
Would this be a hardware issue, or could there be something in Windows 7 that's affecting it? I have disabled the windows firewall and AVG and still can't get any access from either Firefox or IE.
A couple of times I was able to get onto the first page of the console through IE, but if i tried clicking anything else it would ask for the username/password again and not connect. Now it won't even let me in once.
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
I have connected 2 SG500x switches using an SFP-H10GB-CU1M SFP+ Copper Cable module. Since the port shows as a 10G port, I would expect the speed to show as 10G as well. However, it shows as "Unknown". This doesn't leave me with confidence that it is being recognized properly. The link is working properly, but I haven't run tests to verify if I'm getting full 10G throughput or not. Shouldn't it show 10G as the link speed?
