Cisco Routers :: WRVS4400N - Unable To Access Admin Console

Jan 18, 2013

Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
 
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
 
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
 
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
 
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
 
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.

View 3 Replies


ADVERTISEMENT

Cisco Routers :: WRVS4400N - Admin Console / No Response

Aug 29, 2011

I am having intermittent problems with wireless connectivity to this router.  It stops responding to requests completely but existing connections continue to function. 

The hardwired connections also are functional but I cannot get to the admin console to see what is going on. The router is currently not being used to connect to the outside world.  When it was before this situation still existed.  I am using firmware version V2.0.1.3

View 1 Replies View Related

Unable To Access Linksys Console

May 2, 2012

I have linksys ADSL Router which is having one line port for Phone Line and 4 Ethernet Ports.The Router IP is 192.168.1.1. When i connect this Router through one of its Ethernet Port to one of the Network Point(which is DHCP enabled)is working fine. I get the IP 192.168.3.x from my existing DHCP not from the ADSL Router which is enabled.Secondly, Although i can Ping the Router IP 192.168.1.1 from Wifi client 192.168.3.X, But when i try to open the Router Console a Login window open and is says " your are trying to access the Router in an insecure ways and it doesnt not authenticate ID and PWD.When i directly connect Router to my Laptop then am able to do so.

View 1 Replies View Related

D-Link DIR-601 :: Unable To Get WAN Admin Access?

Apr 13, 2012

Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)

View 3 Replies View Related

Wireless :: Unable To Access Linksys Router Console?

May 2, 2012

My Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?

View 1 Replies View Related

Cisco Firewall :: FWSM 3.2.6 / Unable To Access From Switch Console

Aug 15, 2011

I am having FWSM in active /standby mode deployed on two different cat 6k chassis. Unable to access the fwsm module from switch using ' session module mod_no processor 1 ", it throws error " % telnet connections not permitted from this terminal" Running Version 3.2.6 on fwsm, Cat 6k is running 12.2.33.SXH1,
 
switch#session slot 3 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
% telnet connections not permitted from this terminal
---------------------------------------------------------------------------
 
have allowed telnet on line vty, configuration on Line vty is simple allowing all transport protocols
 
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
line vty 5 15
exec-timeout 5 0
transport input all
transport output all

View 3 Replies View Related

WRT120N Can't Connect To Admin Console

May 30, 2012

I was trying to get into my router to give it a reboot yesterday, but was unable to get into the console. I used the username/password I've used for over a year (it was also auto saved) but it would not let me in. I went through all the steps to do a hard reset/restore default settings and it wouldn't let me. I had to access the boot loader to reload firmware, and that worked out just fine.

Now, I still cannot get access to the administration console with the default username (blank) and password (admin). I've tried moving my PC to ports 1-4 and none work.

I was about to give up on the router but I tried connecting from my iPhone and everything works just fine. I was even able to change my SSID and WPA key again.

Would this be a hardware issue, or could there be something in Windows 7 that's affecting it? I have disabled the windows firewall and AVG and still can't get any access from either Firefox or IE.

A couple of times I was able to get onto the first page of the console through IE, but if i tried clicking anything else it would ask for the username/password again and not connect. Now it won't even let me in once.

View 6 Replies View Related

D-Link DIR-825 :: Can't Seem To Login Into The Admin Console

Mar 12, 2013

I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w

View 1 Replies View Related

Cisco Firewall :: ASA5510 - Admin Console

Sep 4, 2011

Our main ASA5510 is set up to failover to a second 5510, and is using the management port for that purpose. All of the other LAN ports are in use.
 
Currently we can manage the ASA using ASDM5.2 from and device on the LAN.
 
We are now going through PCI Compliance, and one of the vunerability scans has picked up the fact that the firewall appears to accept connections on SSL v2. However, if I try to set SSL to use v3 or TLS v1 only (as we don't use webVPN), I get a message that I will no longer be able to use ASDM to manage the firewall as changing to SSL v3 will 'prevent ASDM from establishing a secure connection with the ASA'
 
So does this mean that the ASA does use / accept SSL v2? The help files say that it will accept 'hellos' in v2 but will then try to negotiate to SSLv3 or TLS v1. It doesn't give more details about what happens next, but I would have assumed that if it can't negotiate to one of the later protocols it will drop the connection - is this correct? If that's the case I may be able to get PCI to accept it.
 
However, if this is not acceptiable and I have to switch to SSL v3, what options do I now have of administering the ASA through a GUI?

View 1 Replies View Related

Cisco Routers :: Unable To Combine RV016 With A WRVS4400N

Dec 2, 2011

I just installed a new RV016, and have it up and running currently using just one WAN (cable) on the Internet2 port. Just FYI I do plan to have a second WAN on Internet1 (DSL) once I get this next step working and want that to be the dafault provider, hence the use of Internet2 for this first connection.I already have a WRVS4400N installed that has a whole network on it that will be independant to the new the network and am trying to connect the WRVS4400N to my RV016. It is currently plugged into port 8 of the RV016 and the port is currently set to VLAN2.I know just enough to be a danger to myself here. :-) The RV016 is using the default IP of 192.168.1.1 while the WRVS4400N uses 192.168.10.1.I do know that "Typically, a Cisco RV0xx Series router is used as an access router, with a single LAN subnet. By default, the firewall is pre-configured to deny LAN access if the source IP address is on a different subnet than the router’s LAN IP address. However, you can enable multiple subnets to allow this router to work as an edge device that provides Internet connectivity to different subnets in your LAN."Hence I have added added the 192.168.10.1 subnet with mask 255.255.255.0 (to the RV016) and have tried switching the WRVS4400N from Gateway mode to Router mode. The RV016 can see it but nothing on the WRVS4400N network has any internet access, while computers on RV016 do. I assume this is because of the firewall blocking the traffic.

View 3 Replies View Related

Cisco Routers :: WRVS4400N Router Unable To Login

Aug 9, 2012

Just installed a new WRVS4400N router.  wireless working.  however refuses to let me log back via Ethernet cable in at URL given me 403 Forbidden, Access Denies, Management via WLAN is not allowed.  Was able to reset and noe braodcasting unsecured "cisco b" signal, but no way to get into router and set up security.  unsure what I have done. 

View 1 Replies View Related

Cisco Switching/Routing :: 2960 / Unable To Access Switch Via Console?

Dec 27, 2012

I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.

View 11 Replies View Related

WRT120N Can't Connect To Admin Console After Reset

Jan 1, 2013

I reset my WRT120N and after rebooting i entered user name :admin /password:admin as usual but it refused my access.

View 2 Replies View Related

Cisco Wireless :: WAP2000 Admin Console Not Accessible?

Feb 13, 2011

I'm having an issue with our WAP2000 access point.  I had to reset the access point and now I can't access the admin console.  I've set a static IP address just as I did when I first set it up. Now when I browse to the 192.168.1.245 in my browser it just displays an Authentication error. 

View 1 Replies View Related

Unable To Access Admin Page Of Baitone Router?

May 22, 2012

I was doing some changes in baitone router due to mistake i have disabled something in it.Now i am not able to access its admin page....Before it i was accessing through 192.168.1.1

View 3 Replies View Related

Cisco Wireless :: Unable To Console Into 2600 And 1552 Series Access Points?

May 7, 2013

We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).

View 4 Replies View Related

Linksys Wireless Router :: Unable To Access Cisco Admin Page For 54G V5

May 3, 2012

I moved. Runnig an iMac at home. Can connect to the internet but was not able to access my cisco admin page for 54G V5.  Also need to connect VPN but unable to. 

View 1 Replies View Related

Cisco Switching/Routing :: Unable To Access C2811 Router (AC Operated) Through Console Port

Jan 11, 2012

I not able to access cisco 2811 router (AC operated)  through console port when I try to access it by selecting COM Port, but I  able to access by selecting the TCP/IP option.

View 5 Replies View Related

Cisco Routers :: RV042 - Access Web Admin

Jun 12, 2012

brand new RV042 client (tried MacOS and Win7 on two laptops) will get IP from DHCP and shows correct IPs for gateway etc. - however entering the IP 192.168.1.1 to access web admin does not work (tried current versions of Firefox, safari and Firefox); browser is not offline router was reset to factory setting (by pressing reset for over 30sec) ping on IP above works
 
hardware broken?

View 3 Replies View Related

Routers / Switches :: Can't Access 192.168.1.1 Using Admin ID And Password

Mar 29, 2013

what to do with my router cdr -king i cant access 192.168.1.1 in second time. i access it for the first time but i forgot to configure password now i cant connect using ID:admin Pass:admin

View 2 Replies View Related

Cisco Routers :: WRVS4400N V2 - DIAG Always On / No Access

Apr 21, 2012

After a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
 
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"

View 1 Replies View Related

Cisco Routers :: Access LAN Resources Through WRVS4400n?

Apr 24, 2012

I am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.

View 1 Replies View Related

Cisco Routers :: How To Access RV220W Admin Page On IPad

Jul 14, 2011

How to access the admin page of the RV220W from an iPad wih the default security certificate? If so, what steps did you go through? Or is this only possible when purchasing a certificate?

View 10 Replies View Related

Cisco Routers :: WRVS4400N - Access VPN When Assigned By DHCP?

Jul 6, 2012

My ip address of my WRVS4400N changes every so often. when i use the ip assigned to connect remotely, it works until the ip is re-assigned through dhcp. I know there is a way around this bu ysing a name or something. I just don't know how to set that up.

View 1 Replies View Related

Cisco Routers :: WRVS4400n Port Forwarding (SSH Access)

Apr 23, 2012

I have a WRVS4400n and a CentOS server that I need to enable a SSH access to from WAN. I created a single port forward rule to open port 22 and forward to server (which address is 192.168.41.3) However ssh connect doesn't happen, the command "ssh user@{external_IP}" times out after 20 seconds. If I connect my server directly to modem through outside interface - I have no problems connecting to it. Once it's behind router - no luck. I even added same rule for UDP, not sure if it's needed, but it definitely didn't hepl. The router is on firmware version 2.0.1.3, version on a bottom is 2.

View 4 Replies View Related

Cisco Routers :: IPSec Access Control On WRVS4400N?

Oct 7, 2011

I have a WRVS4400N, and need to apply access control to an IPSec tunnel that terminates at a client site, but can't seem to make the device comply.
 
I can configure ACLs on their device for the LAN to restrict packets coming back into my network, and can restrict packets outbound frm my LAN but that is hardly a secure method of doing this in my opinion.

View 1 Replies View Related

Cisco Routers :: WRVS4400N Internet Access Policies Blocking Everything

Aug 8, 2011

After updating the firmware of my WRVS4400N from V 2.0.1.3 to 2.0.2.1 all traffic was blocked for all machines, even some not included in the list of PCs. As the log was showing that all traffic was blocked by access policies, I disabled the only rule I had (blocking access to some sites to some MAC address list) and everything worked fine.I tried creating a new, simpler rule but after activation it blocked again all traffic for all the LAN.After many trials, I decided to roll back to the previous V2.0.1.3 which solved this problem.

View 1 Replies View Related

Cisco Routers :: WRVS4400N Internet Access Policy Not Working

Jun 23, 2012

I am trying to create an IAP for a single computer based on it's MAC address.  I want to block certain keywords and websites 24/7.  When I setup the IAP as number 1, I add the MAC address of the computer in question.  I then Select Allow and choose Everyday and 24 Hours.  I type in the forbidden domains and click add after each one.  I type in the keywords and click add after each one.  After I click on Save, all of my computers on the network lose internet access.
 
I have WRVS4400N VPN Version 2, firmware version 2.0.2.1

View 2 Replies View Related

Cisco Routers :: WRVS4400N Wireless Client Has No Internet Access

Jul 18, 2012

I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever. However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
 
I have:reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.Tried to move the router close to the laptop, no difference.

View 4 Replies View Related

Cisco Routers :: Wireless Clients On WRVS4400n Cannot Access Server

Mar 10, 2012

When clients connect wirelessly to the WRVS4400N they successfully get a DHCP address from the Windows 2008 server.  After they have the address they can no longer access the server.  It cannot be pinged, no drives can be mapped and internet access fails because the same server is running DNS.  The WRVS4400N is setup for DCHP relay to the server.  Wired clients do not have this problem.  Wireless clients that connect to a secondary WAP on the same LAN also do not experience this problem.  I have updated the router to the latest firmware version, reset it to factory defaults and reconfigured from scratch.  Turning the server firewall off has not made any difference either.  I have been able to bypass the internet problem by adding a second external DNS server in the DHCP scope options. 

View 5 Replies View Related

Unable To Access Router Admin Page Haier R800 Router

Dec 13, 2012

Unable to access router admin page for Haier model R800

View 1 Replies View Related

Cisco :: Unable To See Log Messages Via Console

Feb 11, 2013

i have been facing this problem as i cannot see any log messages via my console port,except by looking at logs manually by "show log" command,

View 3 Replies View Related

Cisco Switching/Routing :: Unable To Console / Ssh To 6513

Aug 9, 2012

I have a 6513 with redundant sup 720-3B's that I cannot get onto.  In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box.  Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module.  I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console.  I have rebooted the entire chassis and don't get anything on my console while booting.  I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis?  The power supply is a 3000w with a 32amp input.  The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit?  I have reseated the power supply also but the same result.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved