Cisco :: Unable To See Log Messages Via Console
Feb 11, 2013i have been facing this problem as i cannot see any log messages via my console port,except by looking at logs manually by "show log" command,
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3750 Turn Off 802.1x Console Messages
Dec 16, 2012Is there a way to turn off 802.1x authentication messages to the console of a 3750 switch? The issue we have is that we like to monitor the terminal when remotely configuring our switches. However, every time a computer authenticates to the network we get messages and sometimes quite a few depending on the situation.
View 3 Replies View RelatedCisco Switching/Routing :: C4507R+E - How To Disable Radius Messages In Console Mode
Jan 14, 2012I am using radius authentication on C4507R+E with supervisor card 6L-E and IOS 15.0.2(SG1). It works perfectly but all radius messages appear in the console. Radius is very verbose, I can't use console because of the significant number of messages and I am worried about switches performances. I add that all debug commands are disabled.
View 1 Replies View RelatedCisco Switching/Routing :: 4506 Phones Connected To Module Went Down / Messages Logged On Console
Sep 25, 2011We are facing issue with one of the module installed on cico 4506 swicth. All of a sudden cisco phones connected to that module went down and the messages logged on the console. [code]
View 9 Replies View RelatedUnable To Access Linksys Console
May 2, 2012I have linksys ADSL Router which is having one line port for Phone Line and 4 Ethernet Ports.The Router IP is 192.168.1.1. When i connect this Router through one of its Ethernet Port to one of the Network Point(which is DHCP enabled)is working fine. I get the IP 192.168.3.x from my existing DHCP not from the ADSL Router which is enabled.Secondly, Although i can Ping the Router IP 192.168.1.1 from Wifi client 192.168.3.X, But when i try to open the Router Console a Login window open and is says " your are trying to access the Router in an insecure ways and it doesnt not authenticate ID and PWD.When i directly connect Router to my Laptop then am able to do so.
View 1 Replies View RelatedCisco Switching/Routing :: Unable To Console / Ssh To 6513
Aug 9, 2012I have a 6513 with redundant sup 720-3B's that I cannot get onto. In short, one of the power supplies failed, it still passes traffic but I can't console or ssh to the box. Other than the two sup 720's, I have a 4 port 10gig card, a 16 port GBIC Card and an IDS module. I have tried removing the 10Gig, IDS and one of the sup's but still don't get anything on the console. I have rebooted the entire chassis and don't get anything on my console while booting. I have tried changing the speed of my terminal to every setting available incase someone has changed it at some stage but to no avail. I have tried swapping sup's, using only one at a time in the chassis but not getting anything. Is there anything else I can try to get onto this chassis? The power supply is a 3000w with a 32amp input. The failed power supply had tripped a switch, when i brought it back up, the power supply came out but the output failed LED is on. My #questions are, is there anything else I can do to try get onto the console, and is the power supply goosed when the RED LED is lit? I have reseated the power supply also but the same result.
View 2 Replies View RelatedCisco Switching/Routing :: 1841 - Unable To Make Router To Send Syslog Messages To Server
Dec 15, 2012I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
Cisco Routers :: WRVS4400N - Unable To Access Admin Console
Jan 18, 2013Although I hasten to point out that I have owned and used an 'IBM' type PC since 1988 and have always managed to get things configured correctly until NOW!
Apart from the last time I tried to use a Linksys product. I had the WRVS4400N recommended to us by a friend as we run a small FTP server to share promotional materials amongst sales operatives around the world, wanted to protect it from intrusion and was told that a Cisco Linksys product with a VPN was the way to go.
I duly purchased a WRVS440N and have been trying to log into the admin console via both browsers (IE9 and Google Chrome) that are installed on a laptop running Win7 which in turn is the only thing connected to the stated device via ethernet port 1... I have tried accessing it via http://192.168.1.1 and have even tried a suggestion from another forum to try https://192.168.1.1 - this only results in my being told that the address does not have a trusted certificate and I even tried every suggested workaround...
I have tried all kinds of reset periods from 10 seconds to a minute, both hot and cold and each time the result is the same - I type in 'admin' and 'admin' in the appropriate boxes and the dialogue box continues to return to the browser window with empty fields...
The shame is that I have managed to re-flash a BT Voyager 190 ethernet modem successfully with DynaLink v3.29a firmware (which allows it to be used with any ISP besides AOL [for whom this modem was solely intended]) and can set it up as a DHCP server, non-DHCP with a single link to another server or non-DHCP and no link.... The point is the modem works... I'm using it right now to type this! We have a single static IP from our ISP and the BT modem is working just fine (as is the TP-Link wireless modem/router that the WRVS4400N was intended to replace)... there are other options in it's firmware for port forwarding, etc and I'm convinced that it wil be adequate for use in conjunction with the WRVS4400N.
I have to concede that the WRVS4400N was not sold to us as NIB; it was sold as re-conditioned and was shipped to or via Ingram Micro Distribution from Cisco Systems, Veldweg 3, Herkenbosch 6075 NL (Holland) via UPS on or about the 31st of July, 2012... there is a shipping label on the original packaging that tells me that so it has in fact been back to Cisco at some point and for some reason.
Cisco Firewall :: FWSM 3.2.6 / Unable To Access From Switch Console
Aug 15, 2011I am having FWSM in active /standby mode deployed on two different cat 6k chassis. Unable to access the fwsm module from switch using ' session module mod_no processor 1 ", it throws error " % telnet connections not permitted from this terminal" Running Version 3.2.6 on fwsm, Cat 6k is running 12.2.33.SXH1,
switch#session slot 3 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
% telnet connections not permitted from this terminal
---------------------------------------------------------------------------
have allowed telnet on line vty, configuration on Line vty is simple allowing all transport protocols
line vty 0 4
exec-timeout 5 0
transport input all
transport output all
line vty 5 15
exec-timeout 5 0
transport input all
transport output all
Wireless :: Unable To Access Linksys Router Console?
May 2, 2012My Linksys Routers IP is 192.168.1.1 am unable to access the console, although i changed the computers IP 192.168.x.y. i have tried by Hard Resetting the Router but still the same?
View 1 Replies View RelatedCisco Switching/Routing :: 2960 S - Stack Of 4 Unable To Console From Members?
Sep 10, 2012I have stack of 2960 S switches.I can console only from Master not from memember switches is this default behaviour?
View 1 Replies View RelatedCisco Switching/Routing :: 2960 / Unable To Access Switch Via Console?
Dec 27, 2012I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies View RelatedCisco Switching/Routing :: C2950-24 / Unable To Take Control In Console Mode
Jan 25, 2012I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
Cisco Wireless :: Unable To Console Into 2600 And 1552 Series Access Points?
May 7, 2013We are having a hard time to console into to the APs using the serial connection (USB to serial converter).We have tried the recommended settings (9600, 8 bits, no parity, 1 stop bit, no flow control (also tried XON/XOFF)) without any success.We are able to connect to 3560 series switches and 5508 WLCs using the same cables, notebook and application (putty, hyperterminal & secureCRT).
View 4 Replies View RelatedCisco Switching/Routing :: Unable To Login To 2960 Via Console Through Terminal Server
Oct 23, 2012I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server, and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
I tried resetting the line on the terminal server, but that didn't work.
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.
Cisco Switching/Routing :: Unable To Login Through Console Port On 1941 Router
Mar 12, 2012I have a strange issue that I am having an issue figuring out. I am trying to login to the 1941 router through the console port. When I enter the username and password, which I just set, it fails. I am able to login under a different login but when I try to enter the enable mode the enable password doesn't work, which I just set as well. I can login with the TACACS+ login from a SSH session. Here is the line config:
line con 0
exec-timeout 15 0
logging synchronous
[Code].....
Cisco Switching/Routing :: Unable To Access C2811 Router (AC Operated) Through Console Port
Jan 11, 2012I not able to access cisco 2811 router (AC operated) through console port when I try to access it by selecting COM Port, but I able to access by selecting the TCP/IP option.
View 5 Replies View RelatedCisco Switching/Routing :: 2691 - Unable To Reach Enable Mode By Console Connection
May 10, 2012I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
Linksys Wireless Router :: WAG200G - Unable To Get 192.168.1.1 Setup Console In Bridge Mode Only
Jun 13, 2012I'm using Linksys WAG200G Wireless modem and connection mode is "Bridge Mode Only", in this mode I'm not getting the 192.168.1.1 setup console and Wifi facility.
View 3 Replies View RelatedCisco WAN :: POE Log Messages On 857 Router?
Oct 3, 2012I have noticed poe log messages in my cisco 857 router, looking around there is mention of a cosmetic ios bug pertaining to 877 router but not the 857. BUG - CSCsd68389. Why i am getting these errors on my 857?
001586: Oct 5 11:25:06.499 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE
001587: Oct 5 11:25:06.499 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0
001601: Oct 5 13:06:29.879 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE
001602: Oct 5 13:06:29.879 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0
001603: Oct 5 13:06:31.387 NZST: esw_dtc_ltc4258_reg_write: no acknowlege from POE
001604: Oct 5 13:06:31.387 NZST: esw_mrvl_pdc_hardware_config failed on slot 0/0
[code].....
Cisco :: ASR1000 CUBE SP Log Messages
Dec 6, 2012we're trying to integrate our SBC instances (CUBE SP on ASR1000) into our network management system (EMC SMARTS)Syslog messages from SBC instances are some kind of cumbersome with lot of line breaks resulting in multiple syslog messages the NMS must parse.How do I configure it to just put it all into one line just as "normal" log messages?
View 2 Replies View RelatedCisco :: LMS 4.2 Not Processing Syslog Messages
Mar 12, 2012I have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies View RelatedCisco :: LMS 4.1 - No Syslog Messages Appearing?
Sep 28, 2011LMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies View RelatedCisco :: LMS 4.0.1 Not Processing Syslog Messages
Jun 19, 2012My Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies View RelatedCisco :: Syslog Messages Not Showing With LMS 4.1
Mar 3, 2013I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
Cisco :: LMS 3.2 - Invalid Syslog Messages
Aug 22, 2011I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
Cisco :: Can IPM LMS 4.1 Send Messages Or Traps
Dec 21, 2011We need IPM (LMS 4.1) to send and e-mail, sms o trap to NNM, is it possible??
View 2 Replies View RelatedServers :: Can't See Messages On Facebook?
Feb 7, 2013what can i do if my computer is not letting me see my messages on facebook what
View 1 Replies View RelatedKeeps Repeating 2 Messages Then Timing Out?
Mar 30, 2011it keeps repeating 2 messages then timing out
View 1 Replies View RelatedD-Link DIR-655 :: What Does Syslog Messages Mean
Jul 26, 2012I'm getting the Syslog messages frequently on daily basis.
View 4 Replies View RelatedCisco :: Debug Syslog Messages In Router
Jun 26, 2012Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedCisco :: Getting DHCP Client Messages On Boot
Apr 25, 2013I have a Cisco ASA 5505 I've configured as a DHCP server. I'm getting DHCP on workstations attached to the appliance, but I'm getting the following message when the appliance loads:DHCP Client: can't enable DHCP Client when DHCP Server/Relay is running on the interface DHCP: Interface 'inside' is currently configured as SERVER and cannot be changed to a CLIENT by a CLIENT featureI'm not trying to configure this thing as a client, so I'm not sure why the system is producing this message.
View 2 Replies View RelatedCisco :: S370 - Getting Critical Messages After Installation
Jul 27, 2011After installing a S370, and upgrading AsyncOS, I have critical messages such as:
An application fault occurred: ('journal/base.py _check_file_size|371', "<class 'journal.exceptions.CorruptError'>", 'CorruptError: File size does not match (33328990208 38708391936)', '[coeuslog/coeuslogd.py run|909] [coeuslog/coeuslogd.py _run|872] [journal/base.py mount|437] [journal/base.py _mount|493] [journal/base.py _recovery|577] [journal/base.py _check_file_size|371]')
Product: Iron Port S370 Web Security Appliance
Model: S370
Version: 7.1.0-307
Serial Number: 842B2B49C468-CNLVX4J
Timestamps: 27 Jul 2011 12:16:03 +0200