I have two SG300-20 Switches and buy two MGBLX1 Modules for the Switches.
I plugedin the Modules but the Modules didn`t work and in the WebConsole i can´t see the Modules.
Is there any configuration to enable the SFP Modules? or is it a problem from my Switches
I was positively surprised to find the optical transmit/receive values using the show fiber-ports optical-transceiver detailed command on a SG300-10.
Now I'm wondering if there is also a SNMP-MIB to query these values? I've already tried the CISCO-ENTITY-SENSOR-MIB used by the larger devices running Cisco IOS, but this didn't work.
I received an SG300-MP as an RMA replacement for a Linksys SRW2008MP and I can't seem to get the SNTP to work.Previously on other devices I have only had to set the SNTP server name or IP address and that was it. So some of the options of the SG300 are foreign to me.So I first set
Administration > Time Settings > System Time > Main Clock Source (SNTP Servers) [X]
Then I set several SNTP server IP addresses
Administration > Time Settings > SNTP Unicast
SNTP Client Unicast [X] Enable
> Add
Other / 64.147.116.229 (nist1-la.ustiming.org)
Other / 24.56.178.140 (wwv.nist.gov)
Other / 128.138.141.172 (utcnist2.colorado.edu)
Other / 129.6.15.29 (time-b.nist.gov)
Some servers I set "Poll Interval" and some I didn't because I wasn't sure what this does.The status for all servers indicate "Down" with 31.12.1899 0.0.0 for the "Last Response"/I found those IP addresses via [URL] Also the setting
Administration > Time Settings > System Time SNTP Multicast / Anycast
I have disabled, and I don't know what this does either...
Using a sg300-52 switch I created two VLANs that share a port for access to the internet. All original devices added to the VLANs are functioning correctly so I have to beleive the VLANs are set up correctly. I added a new desktop and an old laptop to the VLAN and neither worked. I was able to get the desktop to work by enabling VLAN tagging in the network adapter. The laptop is 5 years old and it does not have any such setting in network adapter. There are 2 other devices that share the same port with the laptop and they both function properly. My conclusion is that the laptop does not support VLAN tagging. Is there someway to configure the switch to account for this?
View 6 Replies View Relatedi am trying to get a SG300 work as a router between VLAN's?So fare without any lock?Test setup one SG300 switch and 2 PC's ?Ping works from host to VLAN IP's, but not from host A to host B
Here is the host configuration
<TABLE style="BORDER-BOTTOM: #000000 1px solid; BORDER-LEFT: #000000 1px solid; WIDTH: 400px; BORDER-TOP: #000000 1px solid; BORDER-RIGHT: #000000 1px solid" class=jiveBorder border=1 cellSpacing=0 cellPadding=3 mcestyle="BORDER-BOTTOM: #000000 1px solid; BORDER-LEFT: #000000 1px solid; WIDTH: 400px; BORDER-TOP: #000000 1px solid; BORDER-RIGHT: #000000 1px solid">
[code]...
Here is the switch configuration
SG300 with FW 1.1.2.0 configuration i L3 mode
set system mode router
confip routing (needed on SG300??? - ti is on a 3560 i PacketTracer)
vlan databasevlan 5vlan 6vlan 7
[code]...
I've got an SG300-10 connected back to back (trunked) with a Cisco 3560X switch, across a fibre link and am seeing some big inconsistencies in terms of unicast data transferred across the ports between them.
During a night time window of 4am - 6am I run backups which involves a large copy of files, that almost saturates a GigE link - we can see from the 3560X end that the link is running at a bit over 800MBit/sec of throughput, sustained. The duration of this transfer is consistent with the size of the files being transferred (ie just over an hour, and is what I'd expect for a data transfer of about that amount). Back-of-the-envelope calculations indicate that the 3560X is measuring this data throughput correctly.
However on the SG300 end of the link, which is also being polled by the same application (Cacti), I'm observing spikey counts of only around 20MBit/sec during that window. These counters are very obviously incorrect - there's a huge amount more data moving across the port than that. The incorrect calculations are showing on both the trunk port out of the SG300 (uplink) as well as the interface where the NAS is connected in (which is an access port).
Cacti is polling the OID: .1.3.6.1.2.1.2.2.1.16.57 which translates to IF-MIB::ifOutOctets.57 = Counter32.I'm running version 1.3.0.62 but this problem is not new to this release - previous releases and 1.2 based releases also had this problem.
It looks like multicast traffic may be being counted correctly (that's only a suspicion though), however what I am certain of is that there is a very large discrepancy with the unicast traffic counts.Is this OID the correct one to be using for this switch?
I have an SG300-20 here for testing (firmware: 1.1.2.0, boot version: 1.0.0.4, language version: 1.1.1.6 English). Everything seems to work on it, except, that if I choose Radius authentication by mac address only, then the switch does not honor the Idle-Timeout and Session-Timeout attributes from the Radius server (freeradius).
The setup is the following: I have a no name access point plugged in to switch port gi1. The port gi1 is set up for Radius authentication by mac address only. The access point itself is authenticated, no problem with that. If I connect through the access point by (say) a mobile phone, it is authenticated, no problem. The radius server does send the Idle-Timeout and Session-Timeout attributes, I checked it by running "freeradius -X", both are set to 30 seconds. Then I turn off the wireless card in my mobile phone and check the dot1x users by "show dot1x users". My mobile phone's mac address remains there for 5-10 minutes, so the Idle-Timeout and Session-Timeout does not work.
Another way I could resolv this problem is by explicitely asking the switch to reauthenticate the user. Unfortunately there is no CLI command to do just that, I can do however a reauthentication on a port using "dot1x re-authenticate gi1" (for example). But it does not work as it is expected: the switch uses the stored mac-address to reauthenticate the user, so nothing changes on the port (unless something changes in the radius server). I think it should work like the following: remove the authenticated user from the port, and whenever that mac address makes some network traffic, then reauthenticate as if it were a completely new connection. BTW: it would work for me also if I could just remove an authenticated user from a port, but I did not find a command to do that.
As a last resort I can simply shutdown the port, bring it up again ("shutdown" and "no shutdown" in the interface config), then all users are removed from the port and they all mush reauthenticate. But it causes a network outage for a couple of seconds for all users on that port, on a busy access point it is quite disturbing, and it is not an elegant way to do this.
So my actual question is: is there a way to remove an authenticated user either automatically (Idle-Timeout and Session-Timeout) or manually from this switch?
I enclose the relevant part of the running config.
interface range gi1-2
dot1x host-mode multi-sessions
exit
vlan database
vlan 2-4
exit
[code]....
I whish to connect the two switches shown below.The distance between them is 50m (~54 yards), one floor apart, and I would like to link them with the cheapest optical solution possible.I have been given a solution with 19inch patch panel, splitter, pigtail cords, patch cords, SC connectors, i.e., the lot.Not being an expert in networking, I feel that is an overkill solution.
Servers______________________________________ Devices/Other Switches
| ___________________________________________________|
| ___________________________________________________|
V ___________________________________________________V
(SLM2048-EU-SFP port) <----------------------> (GBIC port-CISCO 2950 Series)
^
|
|
SAN
These are our first switches and seems like GUI is lot different than the online. Out intervlan routing is o not working. I am absolutely sure that I setup the switch in L3 mode since it allows me to create mutiple interfaces. I am hoping that this GUI issue is related to interVLAN routing.
Below is the blog I started for InterVlan issue [URL]
This is the link for online simulator and what I see in its IP tab. I know this switch is not SG300. [URL]
This is what I see on our switch.
Our switch version
switchd64684#show version
SW version 1.1.0.73 ( date 19-Jun-2011 time 18:10:49 )
Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 )
HW version V01
1) I have a Cisco SG300-28P. I plan to add a SG300-52. Would it be possible to manage the new switch through the SG300-28P web browser ?
2) There are 2 fans in the POE model SG300-28P. How many fans are they in the non POE switch SG300-52 ?
We have a scenario where we want to connect 14 access layer 2950 switches to Core switch 3750 via optical fiber in a LAN.What model of 3750 Switch should we use to tackle this situation.I have learnt that WS-C3750X-24P should support it.Isnt it?
Can we use optical fiber SFP module to connect 2950 switches to core switch?Does Cisco 2950 Switch support optical fiber sfp module?
Can I connect a single Cat5e cable between two SG300-28 and link them? If so what must I configure?
View 1 Replies View RelatedI have SG300-28P that I am using as layer-3 switch. Recently I ran in to SG300-52 switch and even though loading same firmware doesn't give me option to do layer-3 switching. For SG-300 I see options in GUI to create vlan interfaces under IP information section, while SG300-52 has IP information option only under the management section.let me know if these are 2 different hardware types and L3 is not possible on SG300-52. If its possible to enable L3 switching on SG300-52?
View 2 Replies View RelatedI'm replacing 2 3COM 4500 Swithes with the SG300-52 Cisco switch. We have 3 VLANs, 10, 20, 100. The switch is set for Layer 3 and I have setup DHCP relay. what settings i should set on the Cisco for the following setups:
3COM Setup
#
interface GigabitEthernet1/0/1
[Code].....
We have several of the SG300 Serices switches. We use them to route VLAN traffic to Remote Offices, Internet Connections, and WiFi Access Points.In one remote office we have a SG300-10 setup to route the HQ Network and the remote Office Subnet. The SG300 is Connected to HQ via Fiber and has multiple Tagged VLANs on it. If I do speed tests over the Fiber Link on the Incoming Tagged Netwotk I get Decent performance, 80Mbs. If I switch to a networtk that is not priginating from HQ, and have the SG300-10 route packet, I get dismal performance. 15-20Mbs.
I Fireded up a New SG300-28P FW v1.2.7.76. Added a the HQ VLAN 101 and new VLAN 1025 . Mapped some Tagged and untagged ports for each. Switch was connected to HQ Network as untagged VLAN 101. I put a laptop on an Untagged VLAN 101 port. Ran some tests, cam back with 750-850Mbs. Great. Put the same laptop on a Tagged 101 Port, Configured the NIC for Tagged VLAN 101, Same test, same Speeds, 750-850Mbs.I then Configured laptop for Tagged VLAN 1025. Connected to tagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!
I then Configured laptop for Untagged VLAN 1025. Connected to unagged VLAN 1025 port. Ran speed tests, resuts were 15-20Mbs!It was only the Laptop and the Connection to the HQ net on the SG300-28P. Why is the performance of this unit soooooo poor when it needs to route?Other Switches have FW v1.0.0.27 or FW v1.1.2.0. They have Similar speed issues. All Configured for Layer 3.
does the SG300 switches can be used with Microsoft NLB in Multicast mode?I know on traditional Catalyst switches you can statically "map" IP's to mac's and then to multiple ports but this doesn't seem to work correctly on the SG switches - it gives an error about the mac not being not Unicast?
View 2 Replies View RelatedAny snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedI'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
I'm having alot of trouble trying to connect more that one LAG between two SG300-52 switches.Basically i have configured both switches with the same vlans. For 2 of the vlans i would like to connect them together between the two switches using LAG. Switch1 has Vlan 5 (ports 1-12) & Vlan 10 (Ports 25-36) with LAG configured on ports 1-2 and ports 25-26. I have setup the second switch identical to the first. But when i connect the LAG's there is no connectivty. If i disconnect one LAG the other starts working.Can you only have i interconnect LAG between switches?
View 1 Replies View RelatedI have two SG300 serie switches and two Gigabit connection between them. How do I configured these two links to work toghether like a one 2 Gigabit channel?
View 2 Replies View RelatedAm using a RV042G with a Fiber Optic connection terminated on WAN1 It was working fine untill received a new IP pool . When we configure with the ip on wan 1 and connect the SG300 the WAN Status shows connected but no internet connection. The wan ip doesnt work. If i replace the RV042G with a Netgear Firewall router The connection works fine with the WAN IP.
The network connection is very simple. What is that is not letting RV042G work with SG300?
I recieved my IPS module license for my ASA 5525 . I enetered the key via the ADSM and it prompted me to restart the firewall .. After that i cannot get into the firewall via the ASDM .
View 3 Replies View RelatedI have a question, does the SG300-28 support VTP and STP?. I want to add it to my network's VTP domain so I don't have to manage vlans manually on the SG300-28 and also be able to configure STP to keep my network loop free.
View 2 Replies View RelatedOn my SG300 I set up LAG for the last two ports.
I then plugged them into my SRW224G4P, once I do that I get dropped packets.
I was thinking maybe doing firmware upgrades to both switches?
I need to know how to configure each port in switch SG300-10 to vlans, i need to configure one port "trunk" with catalyst switch and assign 4 ports to different vlans. any solution?
View 2 Replies View RelatedIn the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?
View 6 Replies View RelatedWe purchased a SG300-52 last week to replace a 5yr old Dlink which has worked perfectly. 1 day after the SG300 went it it started crashing with this fatal error problem so I reverted the firmware back from 1.2.7.76 (latest) to 1.1.2.0 but I still get the problems. It crashes when I have it on my lan with users connected or if I just have the switch on my desk with just my laptop connected, so it cant be a load issue or a network topology issue. I already have a Cisco SGE2010 on my network without problems.
View 7 Replies View RelatedI have a question about ACL and binding. I have a SG300 28P and a couple of other linksys switches and Access points that are connected to it via trunks. The cisco SG300 28P is running in layer3 mode and i have created a couple of vlans and one of them is a guest vlan. Now to my question, i create an ACL and an ACE that vill funktion so that guest vlan only can connect to the internet and not the rest of the internal network. And then i must bound the ACL to an interface port or lag, what i can see it is not possible to bind it to an vlan? so if i have a port on some of the other switches that is member of the guest vlan, vill the ACL on the SG 300 stop guest vlan trafic to the internal network that is comming from some of the other switches?
View 1 Replies View RelatedI want to set up a vlan only for the wifi APs and wifi clients on my network. They can't access to any server, only internet acces. I already implement this configuration and its working, but now I want to allowed a couple of laptops to connect to servers in other vlan. what should I do? Should I do it using Mac address of laptops or IP?
View 9 Replies View RelatedYesterday I upgraded my SG300-10P to firmware 1.2.7.76. I was curious about the new SYN Protection feature, but it seems to do nothing on my installation.
The switch is running in Layer 2 mode. I have ACLs in place and DoS prevention is not enabled. I also tried clearing ACLs and enabling DoS prevention. As I understood the Admin Guide enabling DoS in the Security Suite Settings is not necessary for using the SYN Protection.
In my firewall I see about 300 pps with SYN flags only arriving. What "they" do is sending me SYN packest to port 80 from forged IPs, so that my system should send SYN-ACKs to the victim system. In this case it is the Arab Bank. They are down at the moment...I think that is called a spoofed SYN flood attack.
So I thougt the SYN Protection feature should exactly solve that problem but it does not and does not show any "Last Attack" entries.
If I put a SYN filter in place it works, even if I put SYN Rate Protection in place. But that is just a dirty workaround. My firewall blocks those SYN packets with a SNORT rule.
Is there an SG300 or SG500 that has all ports as SFP ports?
View 1 Replies View RelatedI am using a couple cisco sg300 28P switches along with a sonciwall firewall/router. The sonicwall was already in place and working so they didnt want to replace it. I understand how to configure the vlan on the sonicwall, but could use some info on the cisco. I would basically like to create 3 vlans, 1 default for management, 2 for pc's on lan, and 3 for the cisco spa504g phones/'voip. Would i just go into the vlan managment, configure the 2 new vlans and give them two id's? These offices have one network drop, so the phones and pc's will be sharing the switch ports, however the phones have a setting to configure the vlan id so they know which one theyre on. Is there anything i need to do after that? I want to make sure that vlan 3 has the highest priority becuase its voice, is there some qos configurations i need to make on that switch as well? Also, the port that links the two cisco swtiches together, does that need to be set as "trunk" port? I understand what vlans are, but its just the first time ive run into these cisco models. .
View 0 Replies View RelatedI bought the SG300-10 Switch a few days ago and updated it to firmware 1.3.0.59, but i think there's a bug in this firmware. If I go to "IP Configuration" IPv4 Routes" in L3 Mode nothing is displayed. In the log file i see that:
21474773112013-Mar-16 09:51:34Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB. 21474775182013-Mar-14 22:39:22Error%HTTP_HTTPS-E-DIAGNOSTICS: ERROR - in <RL_vtLeadTableGet> tag, can not find the table rlInetRoutingDistanceTable in the MIB., aggregated (1)
Reset of the Switch doesn't work.