Cisco Routers :: RV042G Fails To Work With Public Wan IP When Connected To SG300?
Feb 6, 2013
Am using a RV042G with a Fiber Optic connection terminated on WAN1 It was working fine untill received a new IP pool . When we configure with the ip on wan 1 and connect the SG300 the WAN Status shows connected but no internet connection. The wan ip doesnt work. If i replace the RV042G with a Netgear Firewall router The connection works fine with the WAN IP.
The network connection is very simple. What is that is not letting RV042G work with SG300?
View 4 Replies
ADVERTISEMENT
Feb 6, 2013
I have an issue with routing public IPs on the RV042G. I have been able to route the IP's in a couple of different ways, but there is always a nagging problem.
I have a PPPoE Business Class account with 5 routable public IP's. I would like to route the IPs and manage the private network using the RV042G.
Here is what I have tried and the problem that arose: 1) I used 1:1 NAT and the servers responded with no issue. This would be a workable config however I use Kerberos for single sign-on for my clients. To use this security protocol and bind the clients to the server, I must use a public IP on the server machines. In this scenario however, everything else worked fine. 2) I then tried using the DMZ and putting the servers on the DMZ port with a public IP entered in the network config of the machine. That even worked fine and I was excited until I noticed that the servers were reporting the public IP assigned to the DMZ port as their IP when they sent mail. I then ran a test and that is the case. The servers - each with a public IP - are reporting the IP of the DMZ port. I can't have that because the mail servers need to announce a correct IP so the reverse lookup will match. Once again, a little gnat gets in the soup.
View 2 Replies
View Related
Oct 23, 2012
1) SG200-18 configuration
- VLAN 10 and 20
- VLAN 10: Port 1 tagged, Port 14 untagged
- VLAN 20: Port 1 tagged, Port 13 untagged
- Port 1: 1UP, 10T, 20T Admit tagged PVID 1
- Port 14: 10UP Admit untagged PVID 10
- Port 13: 20UP Admit untagged PVID 20
Port 1 connected to Fiber ONT (On VLAN 10), Port 14 connected to RV042G WAN.Once RV042G LAN connects to SG200-18 (VLAN 1) port, RV042G WAN unable to get public IP and internet connection gone, port 14 showing "Discarding" under "Spanning Tree"
View 17 Replies
View Related
Oct 11, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
View 2 Replies
View Related
Jan 27, 2012
I'm planning to set up a network with two routers and one cable connection. One router will be for public wifi at my business and the other will be for my Point of sale system and private use. I think I have it figured out but want to double check the set up. Someone tell me if this isn't correct or if there's a better way of doing it.Cable modem --> connect via ethernet to Router #1 WAN port. Router #1 Lan port 1: connect via ethernet to router #2 WAN. Now, router 1 and 2 will have two different subnets; 192.168.1.x and 192.168.2.x respectively. Router #2 is the one that I should use for my private network and for the POS system since it can't be accessed by users from router #1 correct? I have DD-WRT installed on both routers but I plan on putting Tomato firmware for router #1 to limit bandwidth for public wifi and keep DD-WRT installed for router #2.
View 1 Replies
View Related
Jun 4, 2013
How can I update my router if my Internet won't work with the router connected? Right now my Ethernet line is going directly from my PC to my modem. Belkin N750.
View 1 Replies
View Related
Mar 25, 2013
How to setup 3 SG300-52 (in L2 mode) as per this diagram:Port 1 on all switches should be able to talk to each other and access the blob at the right.The ports 25 on the other hand should only be able to talk among themselves in their own private vlan. They are to carry sensitive traffic. So I created 3 vlans, vlan 78 for ports gi1, gi51 and vlan 10 for port25,49,50 and a dummy vlan: 666 with the intent of segratating vlan 10 from vlan 78. My attempts so far have failed. ports gi49-50 are configured as trunk ports and gi1,gi51 as access ports as the following cli output (excerpts of the startup config):
vlan database
vlan 10,78,666
exit
interface vlan 1
ip address 172.16.10.11 255.255.255.0
[code]....
Ports gi1 can talk to each other and access the blob but ports 25 refuse to talk to each other. But as soon as I remove the access links to the blob they can! Obviously, at that point port gi1 lose access.Is such a topology feasable or even advisable?
View 7 Replies
View Related
Oct 12, 2012
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23?First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80?
View 1 Replies
View Related
Feb 5, 2013
Trying to ssh from our QNAP to our switches and copy the running-config.These tests are on an SG-300. When ready well be doing the same thing on all of our 2960's. So maybe the SG300 is the problem.
View 1 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
Mar 3, 2013
my router (RV042G V01 Firmware Version : v4.2.1.02 ) get errors I can't understand.Lost connection, can't get a new IP, DNS does not work, total hangup.After a short time / reset everything works fine up to the next error.In the Log I found the following interest entries:undefined Kernel undefined Kernel failed (1).undefined Kernel Message from server.
View 1 Replies
View Related
Sep 24, 2012
I purchased RV042G and setup one-to-one NAT problem to several servers. ometimes the NAT servers lost the internet connection. My case as below
ISP provide two set Public IP Address , one modem
e.g.
set one) 100.100.1.2-6, gateway 100.100.1.1
set two) 200.200.2.2-6, gateway 200.200.2.1
[code]....
All computers and servers (one-to-one NAT) outbound and inbound all work fine. After several hours, only the servers (one-to-one NAT) alert internet connection broken, but the computers (non NAT) still have internet connection.
What's the problem occurs? Why only one-to-one NAT servers lost the connection? and Why only serveral hours later, the server lost the internet connection.
If I changed the WAN setting to same as subnet of the one-to-one NAT, it doesn't occur any problem.
View 3 Replies
View Related
May 20, 2013
I run my business network on the 192.168.x.x range with a server set as 192.168.2.4 statically. The router is currently connecetd to two DCHP wan connections from my ISP, I'm on a residential consumer plan. It has defaulted to loadblanacing with the second WAN however I want to have the second wan's public IP be used by my server and only the server however I wish for the server to still be on the lan so I can use HYPER-V's brided network connection feature to run VMs on the lan, and I would like their wan connection to be from wan 1... as for the entire lan except the server at 192.168.2.4 Is this possible, I can't seem to get the 1-to-1 NAT to do it?
View 4 Replies
View Related
Nov 8, 2012
I've setup the RV042G with one ISP connection for now.I have my main PC running fine, but I have another PC hard lined to the router that had a connection after I power cycled the modem and router but now it no longer does. disabled the network on that PC, now I can't get it back at all.I have a wireless e2000 in one of the ports that I disabled the DCHP on and it seems to be running nicely.before I disabled the PC in question, aka port 3, it was showing as connected in the "192...." but now only as enabled.
View 1 Replies
View Related
Sep 27, 2012
Is there anyway to monitor netflow on RV042G. We have a network at a small school that will get bogged down during the day.
View 1 Replies
View Related
Apr 22, 2013
Have a rv042g, newest firmware, trying to setup one to one nat on the configs page, I select enable, enter private ip , enter public ip, enter the range, and click "add to list" and nothing.... no error message, doesn't add to the list below it
View 1 Replies
View Related
Jan 29, 2013
I have RV042G dual WAN VPN router as a gateway in my small office. My ISP requires from me to connect through PPTP VPN to have access to the network. I've configured my router with static IP and every time I connect a laptop or desktop pc I need to connect to the VPN with the Windows VPN client.
View 3 Replies
View Related
Oct 4, 2012
We have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
This issue happens when using any sort of VPN that's supported by the router.
View 1 Replies
View Related
Oct 17, 2012
I have created a protocol binding rule and even a bandwidth rule to make sure outgoing FTP needs to go through WAN2 interface. But it still goes through WAN1, it only works when I disconnect WAN1
View 13 Replies
View Related
Mar 16, 2013
I have a problem with the RV042G V01 router manufactured 12/2012.
After router settings the router works fine without any problems. After 10 or 12 hours I got the message that the side could not be opened, while no DNS. I checked inside the router and all settings looks ok DNS adresses from ISP are present on both WAN settings . When I use inside the router the funktion for DNS it will work but from any client is does not work. When I restart the router alls works fine. After few hours ( it's differnt 1,2 or 6 ) I have the same problem. No entry in the log's !
View 7 Replies
View Related
Aug 26, 2012
Recently setting up a RV042G for my SOHO. Everything seems to be fine except for SSL port forwarding. I know the router's external static IP is reachable because I test it out with remote management functionality from an external IP. Port forwarding also works correctly because I have other behind the router servers in both UDP and TCP working flawlessly. PPTP VPN also works corrrectly. What I can't get it to run is an Apache server. Looks to me RV042G kind of drop all SSL or HTTP ports from the WAN side.
Configuration:
- 4 port forward rule under "Setup/forwarding" for 80/8080/443 and 8443 all to the webserver with a static IP.
- Firewall page I have Firewall, SPI, DoS enabled.
- Added a firewall rules to allow all HTTP and HTTPS traffic from WAN1 to the webserver static IP.
- Toggle Block WAN Request, HTTPS and multicast does not affect the result.
- Toggle and mapping the remote management port to other port beside 443 does not affect the result.
The same setup will works corretly under my old Netgear FVS router. Am I missing something in RV042G setup?
View 3 Replies
View Related
Jul 8, 2012
I just got the RV042G today. I found the router can only accept 100000 Kbit/sec as bandwith, which is 100Mps only. According to the specification, it should have 1000Mps WAN. I have a internet link of 1000Mps, which is now limited by this router.
View 30 Replies
View Related
Mar 24, 2013
I'm trying to make an attached topology. This router should be attached to 2 different ISPs on both WAN interfaces (ISP1 with IP address - A.B.C.D, and ISP2 with IP W.X.Y.Z) and I want to use DMZ, too. My idea is to make a L2/L3 segmentation with 2 VLANs - Vlan RED for DMZ (private network 192.168.1.0/24) and vlan BLUE for Internal network (network 192.168.2.0/24). I checked in the manual that vlans are supported, but I can't see anything about 802.1q, can I use one trunk port or I should use 2 physical cables?
There should be inter-vlan routing and basic stateful firewall, so PCs in Vlan Blue should be able to initiate connections to DMZ servers, but the opposite should be denied. Router should make a port forwarding on its both WAN interfaces and forward incomming traffic (from Internet) to DMZ servers (with NAT). Both DMZ servers and internal PCs should have an internet access with NAT over both WAN uplinks.
Can I use RV042G for this setup and if not at all - are there any cisco SMB device which can do this?
View 5 Replies
View Related
Nov 11, 2012
How to configure an IPSec VPN with router RV042G.I need to know how to configure an IPSec VPN. Cisco Router with RV042G.
I spend this client your VPN parameters. [code]
View 2 Replies
View Related
Nov 4, 2012
i got a problem in configuring a VPN Connection for our Colleagues (Laptops & Iphones 4/4S/5) We got an RV042G .
A WAN Connection from Deutsche Telekom AG with Static IP connected in WAN1. Configured for PPPoE. Ive got configured a Port Forwarding on our SBS 2011 Server for OWA and other Services on web. I´ve got extreme Problems configuring VPN Connections. We use Quick VPN, other tools got to much buttons to click .
1st i configured a Group VPN , with FQDN (Remote Group) Local Group (IP only) . i configured 2 users. Then on a Laptop connected to the internet through an Hotspot Connection of an Iphone.
I entered the WAN IP .. Username. Password. Pressed ENTER. I get to the point of Verifyiing Network, and after it timeout with Remote Gateway not responding. Do you want to wait. If i Press Yes, after max. 1 minute there comes the message again.
I looked in the VPN Summary, and i see, that my username was connected through VPN for seconds, but then disconnected. Do i have overseen an option to configure??
View 4 Replies
View Related
Jun 5, 2013
We are connecting to a Cisco DPC3825 cable modem supplied by our ISP. It has been configured to act as a switch only. They have supplied us with 2 static IP addresses.
When each WAN port is connected individually, everything is fine. I see the IP addresses on the respective WAN port, and it is working fine.
When I connect both WAN ports to the modem at the same time, I see a large amount of traffic between the WAN ports, as indicated by the port LEDs, and the RV042G becomes completely non-responsive through its web interface.
How do I get the RV042G working with both WAN ports connected?
View 3 Replies
View Related
Mar 5, 2013
I'm about to upgrading our RV042 to RV042G since everything in the Network ist ready for Gigabit except the RV042
I think it's important to mention that another RV042, which is at a 2nd location, will remain for the VPN connection between the two locations. (Older Hardware are used at the 2nd location).
My Question is, are there any known issues, which should be cleared before changing the router.
Mainly issues with configuration migration and compatibility between RV042 and RV042G VPN connections.
View 3 Replies
View Related
May 11, 2013
I'm trying to set up a single web server in a DMZ using the RV042G and the docs seem woefully inadequate to explain how this is accomplished.
I've attach a picture of my setup..
I'm assigned a single Public IP.. in the example I've used 172.16.5.22 and so I've set the WAN interface for static IP.
The DMZ port is not obvious how to set up.. So I've chosen to define a private subnet and throw the web server in there. As I activate the DMZ, I specify a "subnet" and its address as 10.10.10.1, which I'm assuming goes to the DMZ/WAN port. I assign my webserver the address 10.10.10.3.
I leave the Access rules in their default condition.
I am a little unsure as to how to setup the static IP info for the web server.
Gateway: 10.10.10.1 ?
DNS: 10.10.10.1? or 172.16.5.1?
Problem #1
=========
My first problem is that the webserver cannot access the Internet. I get a timeout when I open the browser. I've tried every address there as the gateway and DNS..
Problem #2
========
If a person on the WAN side is attempting to connect to 172.16.5.22:80, how does the RV042G know to send it to the 10.10.10.3 device? It doesn't know what address the webserver is assigned; I just gave it a 10.10.10.1 address as the subnet address.
I think I'm missing something, conceptually here.
Can, in fact, you use the RV042G in this fashion with only a single public IP address? There is almost no information on how the router actually routes traffic when you choose either 'subnet' or 'range' (where the DMZ is in the same subnet as the WAN)
View 6 Replies
View Related
Apr 17, 2013
We looking into options for using VPN to allow users to work from home at our company. We already run Windows Active Directory and have a Cisco RV042G router. We would like to set up a VPN that will authenicate user through AD. Is this possible with the RV042G?
View 2 Replies
View Related
Aug 23, 2012
I am running Cisco ACS 5.1 802.1x with certificate based authentication for Wired and Wireless connections. The issue that I am having is that when a user comes in from home with their laptop the wireless connection works, they pass the authentication and have network access fine. But when the plug the laptop into a docking station the LAN connection fails and gets put in the Auth Failure Vlan. A reboot of the phone/ shut/no shut fixes this, but I really need to find a resolution.This is an intermittent fault and only effects users with both LAN and WLAN enabled. Running ACS 5.1.0.44, all Cisco 3750s - c3750-ipservicesk9-mz.122-55.SE.Certificates are issues by group policy and only using computer authentication.
View 2 Replies
View Related
Feb 13, 2013
I received an SG300-MP as an RMA replacement for a Linksys SRW2008MP and I can't seem to get the SNTP to work.Previously on other devices I have only had to set the SNTP server name or IP address and that was it. So some of the options of the SG300 are foreign to me.So I first set
Administration > Time Settings > System Time > Main Clock Source (SNTP Servers) [X]
Then I set several SNTP server IP addresses
Administration > Time Settings > SNTP Unicast
SNTP Client Unicast [X] Enable
> Add
Other / 64.147.116.229 (nist1-la.ustiming.org)
Other / 24.56.178.140 (wwv.nist.gov)
Other / 128.138.141.172 (utcnist2.colorado.edu)
Other / 129.6.15.29 (time-b.nist.gov)
Some servers I set "Poll Interval" and some I didn't because I wasn't sure what this does.The status for all servers indicate "Down" with 31.12.1899 0.0.0 for the "Last Response"/I found those IP addresses via [URL] Also the setting
Administration > Time Settings > System Time SNTP Multicast / Anycast
I have disabled, and I don't know what this does either...
View 5 Replies
View Related
Jul 13, 2011
Using a sg300-52 switch I created two VLANs that share a port for access to the internet. All original devices added to the VLANs are functioning correctly so I have to beleive the VLANs are set up correctly. I added a new desktop and an old laptop to the VLAN and neither worked. I was able to get the desktop to work by enabling VLAN tagging in the network adapter. The laptop is 5 years old and it does not have any such setting in network adapter. There are 2 other devices that share the same port with the laptop and they both function properly. My conclusion is that the laptop does not support VLAN tagging. Is there someway to configure the switch to account for this?
View 6 Replies
View Related
Jun 9, 2011
I have two SG300-20 Switches and buy two MGBLX1 Modules for the Switches.
I plugedin the Modules but the Modules didn`t work and in the WebConsole i can´t see the Modules.
Is there any configuration to enable the SFP Modules? or is it a problem from my Switches
View 3 Replies
View Related
