I am unable to connect vivotek ip7137 camera with d link or netgear router I tried all my best made the connection with eithrnet cable , reset both machine set static ip of pc but nothing is happening?
I have an Iball Baton Router. I am not able to connect to it from my PC. However, I am able to connect to the router from my Laptop.I have tried isconnecting and renewing the ip. Can see that ip (192.168.1.102) is issued to my PC and can ping to the same. But, do not get any reply when I ping to the gateway (192.168.1.1 - ip for the router). My OS is Windows 7 64 bit.Let me know if you need any more information
I have a wireless router that was named and all the wireless equipment (laptop, ipod, phones) was connecting easily with no problems. Everything is saying "unable to connect". I have no clue what she did but she said her laptop asked her for the 8 number code from the router and she entered it.
I have two windows 2008 machines on vmware. I assign 10.0.0.1/8 and 10.0.0.2/8 to them. Both connected to same virtual switch. Now should these two PCs ping each other? In my case they dont ping. What i get is Repy from <ip address>: Destination host unreachable.
I try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
I have just upgraded my AIM and Skype messengers and now it won't let me sign in. I did before with my old versions. It is saying that my internet connection is bad which it is not. I have looked up ports in my Yahoo messengers, Control Panel and Bit Torrent still nothing.
i have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
I got an old WISE WS-4016 16-port 10/100Mbps Fast Ethernet Switch from a friend of mine which was not in use. However i am unable to find any information regarding this switch anywhere online.Unfortunately we couldn't find any manual for this switch as well.
to enable UPNP on a Virgin Media Super Hub, I have tried using both the IP addresses provided by Virgin media (192.168.0.1 and 192.168.100.1) but regardless of which browser I use the page constantly fails to load.
I am able to connect to corporate VPN with no issues when connecting directly to ISP modem. When I try to complete the same VPN connection via a Wireless Router (Linksys WRT160Nv3) i get the following message: "Network error. Unable to look up host names"I have tried connecting and it will initially connect, but 15-30 seconds it will drop and connection can't be re-established.Is there a setting on the Linksys WRT160Nv3 that needs to be changed?
I am trying to connect two D-link 24 port switches thru cat 6 cable, distance is less than 50 meters, but its not working but if i connecting it with a Laptop i am able to connect to the network. But if i connect the switch in between it fails i tried changing the switch and cable but no use anyone have a clue how it fails?
I am unable to connect to webview on our SRW2024 switch. I use a macpro G5 running 10.6.8. When i try to connect to it through Safari, Chrome, or Firefox using 192.168.1.254, I receive a message that a connection cannot be established. 192.168.1.254 is the ip mentioned in the manual. I used an ip scanner and it showed the actual ip is 192.168.0.1. But I cannot connect to webview through this ip either. We got this switch a year ago and did not change any settings, we just connected it and it worked fine. But now we want to change some settings on the switch but cannot connect.
Trying to connect 2 switches together (both 2960G 8 ports). I have an SFP in each (GLC-LH-SM). They are connecting over SingleMode Fibre using the correct cabling. The fibre cores have been tested and are all ok also.
I can't get no Layer 1 connectivitiy at all. Just dead. I have tried 4 different GBICS, swapped cabled etc.. I have forced the media type to use SFP. No link light....
I thought it would just be a case of plugging in the gbics cables and off I go! I read about forcing the speed and duplex on the port but because the port if SFP, the speed and duplex settings are not available. This seems to be hard coded.
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
I have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
This is an odd one, possibly a broken unit but I have a SRW2024P which has been running for a couple of years all OK but some time ago I noticed I couldn't access the web interface. I decided to leave it until I actually needed to change something, which is now!
After much messing around modifying a null-modem cable to work (i.e. connected pins 2,3 and 5) I managed to connect to the console through HyperTerm. Did a full factory re-set and XMoDem'd the 1.2.9 software on again but still no luck.
I tried accessing the web console and telnet with the default IP and tried setting my own IP but can't even ping them.
There are a few other peculiarities: The units MAC address in the console is shown as 00-00-00-00-00-00The units hardware version is blank in the consoleBoth PING and TRACERT tests fail to any address except the units ownTFTP uploads fail to connect (the TFTP server doesn't even log an access attempt)All other clients connected to the switch are working fine and the port statuses in the console show working connections Basically; it is as if the web/config/admin 'module' is disconnected from the actual switch in some way?
I am trying to portforward so I can host a server of a game I play, but whenever I try to connect to my default gateway it just times out and cannot load.I have done the cmd -> ipconfig/all and I found that my default is 192.168.0.1What do I do