Routers / Switches :: Cannot Connect To 192.168.0.1?
Sep 10, 2012
I am trying to portforward so I can host a server of a game I play, but whenever I try to connect to my default gateway it just times out and cannot load.I have done the cmd -> ipconfig/all and I found that my default is 192.168.0.1What do I do
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
I have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
I recently moved out of state and have been working remotely. I just got a new internet provider who will not let me connect to my office VPN without a small business account which is ridiculous. I've been reading up on how to work around this and haven't been able to figure anything out. I've signed up for a dynDNS account but the truth is I have zero experience with this and don't know what I'm doing - most of the stuff I'm reading is a foreign language to me. I can log into my router and change settings and I can get VPN info from my tech person and work so I just need to know what to do. I can't really work effectively without access to my network but I refuse to pay for a small business account
I'm trying to access 192.168.0.1 to configure my linksys router to add new hardware to my home network but my browser (Safari) can not open the page - error message suggests 'server where this page is located isn't responding.
with a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
First , I have installed the router and modem correctly , and i connected it to the switch , So the other devices connected to the internet but not connected to the workgroup so i can't share the files between the PC's ? Modem >>> Router >>> Switch >>> PC's
I have a Belkin Wireless G Plus MIMO Router and had no problems connecting to corporate in the past until several months ago. I can connect just fine if I bypass the router and connect to the modem. I also have no problem if I go to places like Subway. There is no problem with the wireless internet connection, only a problem when I try to connect to corporate through the VPN.
I have 4 computers on LAN using a router and I cannot see eachother, don't know how to configure the PCs. The router is set on DHCP for LAN, the PCs are using Windows 7 and can connect through the internet the router is providing (4 dells) but don't know how to set the computers to see eachother and to share files.
I'm having trouble trying to connect 3 computers via LAN for gaming using straight Ethernet cables and a net gear router. Only 2 computers seem to connect at a time. All 3 can connect to one another (one at a time) and the I.P. addresses have been set to 192.168.0.1 , 192.168.0.2 and 192.168.0.3. The cables work fine and the computers, but I'm wondering if I'm using the wrong kind of hub/router?
I try connecting to my Linksys wireless N router's setup but it doesnt even find the "site". I have tried pinging the router and i get no response, i have restarted the router and everything, It has never done this before.
I am unable to connect vivotek ip7137 camera with d link or netgear router I tried all my best made the connection with eithrnet cable , reset both machine set static ip of pc but nothing is happening?
I am wondering what the cable wires or sockets on the back of this router are for? could it be you can connect through the cable tv network the sockets fit perfectly in the back of the router thats a strange coinsidence dont you think?
We have a network in place. A week ago we switch to AT&T's UVerse and they replaced the Motorola modem with a Motorola NVG510 modem/router. There was a Netgear router behind the original Motorola but since we only needed 4 ports I pulled that out of the loop and used the Motorola. The three computers connected directly to the Motorola came right up. However, there was a switch with two computers connected to it and when the switch was connected niether of the computers connected to the switch would go to the internet. I took one of those off the switch and connected directly to the Motorola and immediately connected to the internet. Put it back through the switch and nothing.
we're using a network and only one computer can't seem to connect to the printer. it runs on a windows 7. tried reinstalling it but it seems nothing has changed same error messages is coming up each time i tried to setup the printer.
can't access gmail or any https sites at all such as fnb.co.za or auction sites ect... I've tried resetting my rooter, configured all the settings as they were when working, I have basically gone into my network & sharing centre and change adapter settings to make sure all the settings there are as should be, reset , & config all of those as well, I've also gone into cmd and reset my D-link completelly from the command, and also tried to restore my computer to an earlier stage which did not work either , Now all I can gather is that It has to be a block some where most likely with the rooter , which is blocking access to port 443.
A Telindus 1421 SHDSL Router and a Sagem F@st 1500WG wireless adsl router.The question is: Can i connect this two devices directly over the adsl port and share networks on each side of each of the devices?