I have a Belkin Wireless G Plus MIMO Router and had no problems connecting to corporate in the past until several months ago. I can connect just fine if I bypass the router and connect to the modem. I also have no problem if I go to places like Subway. There is no problem with the wireless internet connection, only a problem when I try to connect to corporate through the VPN.
View 3 Replies
Looking for routing with an SA540 router connecting to corporate VPN.We have an odd configuration that is beyond the scope of what I have configured previously with these devices..I am trying to configure the routing to the additional IP addresses listed for the HQ. The VPN tunnel between the .26.120.x and the .17.0.0 networks is built however it does not appear to be routing. The Cisco administrator at the HQ site says that they have "fully configured the routing" from all the listed IP addresses back through the VPN tunnel. The options I am unsure of for configuration of the SA540 router are: GW - I believe that I use the internal IP address of the 17.26.120.x router.Is this logical since the VPN tunnel. We are using NAT for the firewall internally.The existing 3 172.26.x.x VPN tunnels are live and working and fully routing between themselves.
View 2 Replies View RelatedI have created an IPSEC VPN tunnel using a Cisco ASA5520 (corporate) to a Cisco SRP541W (remote). The corporate subnet is 10.1.0.0/16, and the remote subnet is 192.168.1.0/24. From the remote subnet, I can ping anything on the 10.1.0.0 corporate network, but I cannot ping from the corporate network to the remote subnet. At first I thought this was something obvious, perhaps an incorrect acl or something easy on the corporate firewall. However, we have several other vpn tunnels established, all set up the same, and they work just fine. After looking at it a bit more closely, if I ping the remote subnet I see the hit counter increment by one each time, which leads me to believe that traffic is in fact being routed properly.Now I'm thinking that something in the remote SRP541W that is not allowing icmp traffic, but I can't find it anywhere. To be honest I have never used this type of firewall before, they have all been Cisco PIX501/506e and ASA5500 models.
View 2 Replies View RelatedA new Windows 8 computer can't access the SSLVPN corporate connection.
When we try to access the SSLVPN website to download the launcher (you have to download the VPN launcher everytime for our configuration), you can log in and that's fine, and then you can click on the VPN Tunnel link, a popup shows up but it doesn't actually download the launcher. Solutions we've tried so far:
1) Reinstalling C++ Redistirbutable
2) Adding the site to trusted sites and allowing unsigned ActiveX controls
3) Removing all internet objects through internet options.
Is there anything else we can try?
I have some trouble with the setup of an oeap 600 ap. The ap has joined the controller as it should and the remote-lan connection to my corporate network works well, but i can't connect to the corporate wlan.
When i check the event log on the ap it says:
"
*Oct 02 07:36:56.662: (Re)Assoc-Req from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:36:56.665: received assoc-rsp for wireless client, status=0011
*Oct 02 07:37:11.712: DisAssoc-Req/DeAUTH from 00:1a:73:d2:82:8c forwarded to WLC, wired: no
*Oct 02 07:37:11.713: WTP Event: Delete Mobile sent to wlc00:1a:73:d2:82:8c"
and a debug on the controller gives me:
apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Adding mobile
on LWAPP AP ec:c8:82:c2:3a:20(0)
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Association received from mobile on AP ec:c8:82:c2:3a:20
*apfMsConnTask_6: Oct 02 08:52:05.034: 00:1a:73:d2:82:7f Sending Assoc Response to station on BSSID ec:c8:82:c2:3a:20 (s
tatus 17) ApVapId 1 Slot 0
[code]....
how to connect two subnets with two switches and one router using router sim software?
View 1 Replies View RelatedCan I connect 2 routers to one phone line so that I can receive a wireless internet connection throughout my house?
View 1 Replies View RelatedHow do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
how to connect 2 routers on different lan
View 3 Replies View RelatedI am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
View 4 Replies View RelatedI have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
View 9 Replies View RelatedI want to connect two routers wirelessly without running cables , any easiest way without cables.
View 1 Replies View RelatedI am trying to portforward so I can host a server of a game I play, but whenever I try to connect to my default gateway it just times out and cannot load.I have done the cmd -> ipconfig/all and I found that my default is 192.168.0.1What do I do
View 6 Replies View RelatedI recently moved out of state and have been working remotely. I just got a new internet provider who will not let me connect to my office VPN without a small business account which is ridiculous. I've been reading up on how to work around this and haven't been able to figure anything out. I've signed up for a dynDNS account but the truth is I have zero experience with this and don't know what I'm doing - most of the stuff I'm reading is a foreign language to me. I can log into my router and change settings and I can get VPN info from my tech person and work so I just need to know what to do. I can't really work effectively without access to my network but I refuse to pay for a small business account
View 5 Replies View RelatedI'm trying to access 192.168.0.1 to configure my linksys router to add new hardware to my home network but my browser (Safari) can not open the page - error message suggests 'server where this page is located isn't responding.
View 3 Replies View Relatedwith a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
View 3 Replies View RelatedFirst , I have installed the router and modem correctly , and i connected it to the switch , So the other devices connected to the internet but not connected to the workgroup so i can't share the files between the PC's ? Modem >>> Router >>> Switch >>> PC's
View 1 Replies View RelatedI have two dvr 4 channel each and I need to connect them to just one static IP, is that possible?
View 1 Replies View Relatedi was trying connecting two LAN network on different location.
View 2 Replies View RelatedI have 4 computers on LAN using a router and I cannot see eachother, don't know how to configure the PCs. The router is set on DHCP for LAN, the PCs are using Windows 7 and can connect through the internet the router is providing (4 dells) but don't know how to set the computers to see eachother and to share files.
View 2 Replies View RelatedCan conect to the internet but unable to connect to 192.168.0.1
View 4 Replies View RelatedI am trying to extend range of my DIR-615 with a DAP-1360. Part of the installation requires pulling up 192.168.0.50 on my brouser. But it won't pull up.
View 1 Replies View RelatedI'm having trouble trying to connect 3 computers via LAN for gaming using straight Ethernet cables and a net gear router. Only 2 computers seem to connect at a time. All 3 can connect to one another (one at a time) and the I.P. addresses have been set to 192.168.0.1 , 192.168.0.2 and 192.168.0.3. The cables work fine and the computers, but I'm wondering if I'm using the wrong kind of hub/router?
View 3 Replies View RelatedI have a windows 7 and can connect to my router but my windows xp laptop wont connect to the same router i took it back to the shop and they connected it to there wifi. so what can be the problem.
View 2 Replies View RelatedI try connecting to my Linksys wireless N router's setup but it doesnt even find the "site". I have tried pinging the router and i get no response, i have restarted the router and everything, It has never done this before.
View 1 Replies View RelatedI am unable to connect vivotek ip7137 camera with d link or netgear router I tried all my best made the connection with eithrnet cable , reset both machine set static ip of pc but nothing is happening?
View 1 Replies View Relatedcant get my blue ray to connect to wireless. on network connection test it stops on gateway ping?
View 1 Replies View RelatedI have a cricket broadband modem to connect to the internet. I want to use my Dlink di-524 router to share that internet connection with the other computers on my network. How do I do this?
View 1 Replies View RelatedI am wondering what the cable wires or sockets on the back of this router are for? could it be you can connect through the cable tv network the sockets fit perfectly in the back of the router thats a strange coinsidence dont you think?
View 2 Replies View RelatedWe have a network in place. A week ago we switch to AT&T's UVerse and they replaced the Motorola modem with a Motorola NVG510 modem/router. There was a Netgear router behind the original Motorola but since we only needed 4 ports I pulled that out of the loop and used the Motorola. The three computers connected directly to the Motorola came right up. However, there was a switch with two computers connected to it and when the switch was connected niether of the computers connected to the switch would go to the internet. I took one of those off the switch and connected directly to the Motorola and immediately connected to the internet. Put it back through the switch and nothing.
View 4 Replies View RelatedI want to get the internet on my desktop and use the wireless capabilities on the router with the laptop. What does the connection look like?
View 3 Replies View Relatedwe're using a network and only one computer can't seem to connect to the printer. it runs on a windows 7. tried reinstalling it but it seems nothing has changed same error messages is coming up each time i tried to setup the printer.
View 1 Replies View RelatedWe wish to connect up to eight devices using TL-PA211KIT. As these devices have a pair facility, is this possible?
View 2 Replies View Related
