I am having 2 Pc's and 1 ISP. I am havng a DSl modem cum router. Is it possible to connect two computers with 2 different ip addresses from same ISP? My ip address is a static one btw..
View 3 RepliesI'm having trouble trying to connect 3 computers via LAN for gaming using straight Ethernet cables and a net gear router. Only 2 computers seem to connect at a time. All 3 can connect to one another (one at a time) and the I.P. addresses have been set to 192.168.0.1 , 192.168.0.2 and 192.168.0.3. The cables work fine and the computers, but I'm wondering if I'm using the wrong kind of hub/router?
View 3 Replies View RelatedOne computer is an iMac running Snow leopard and the other is running Win 7. I wish to switch either computer to any of the two printers.
View 1 Replies View RelatedI have 192.168.2.1 and 10.10.0.1But i cant connect to 10.10.0.1 network from 192.168.2.1 network. What should I do to connect that both are same network I have a Linksys Router.
View 2 Replies View RelatedWe need internet connectivity on all workstations
View 1 Replies View RelatedMy new employer has asked me to determine any issues that could be causing performance issues our LAN. The network has two subnets and one of the first things that I noticed is that I cannot ping computers on subnet A from subnet B. I've looked into this and found a few things.-I CANNOT traceroute to computers on subnet B from subnet A-I CAN NMAP to computers on subnet B from subnet A-Computers on subnet A CAN ping other computers on subnet A and computers on subnet B CAN ping other computers on subnet B-Computers on subnet A CAN ping and access servers on subnet BI am relatively new to networking and not exactly sure where to start investigating this problem.
View 9 Replies View RelatedI recently got a new Toshiba laptop, which works perfectly. We already have an HP desktop PC as well as a Dell laptop, which are both connected to an Ethernet router. When I got my Toshiba, I couldn't connect to the router, whether from a new Internet cable, the cable the Dell uses, or the cable the HP uses (it works perfectly fine with Wifi). The next day I got up early and tried again, and it worked. The HP was turned on, and it connected. But then the Dell wouldn't. Over the next couple days, we realized the problem was that the router only allowed the first two computers that were connected to it to connect to the Internet, but not the third one. The router itself allows eight cables to be plugged into it at a time, so I don't see why it's only allowing two computers, whether laptop or desktop, to connect. Is there a possible solution to this?It's an 8-Port Workgroup Switch, Model EZXS88W.Also, our router DOES NOT support Wifi
View 1 Replies View Related4 pcs are connected to a adsl bb router having 4 lan ports. i have removed the adsl cable going to the bb router cos bb giving problems. i m then connecting to internet on any one pc using a tata photon usb device. i want to share this internet on other 3 pcs. those 3 pcs are getting their ips from the bb router in 192.168.1.x series. all pcs are pinging to gateway ie 192.168.1.1 but not pinging each other. why?
View 3 Replies View RelatedIn setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies View Relatedhow do i assign IP addresses to 10 computers in a network?
View 3 Replies View RelatedNetgear DG834 allocates IP Addresses using DHCP to 5 computers and 2 tills, the tills addresses and one computer IP addreess are reserved and fixed, so that data can be downloaded from the tills to this computer. However I had to re-format the computer and the Router now allocates a new IP address to it, which the tills cannot recognise, so I cannot download the data from the tills to the computer. Is it possible to change the newly allocated Computer IP address in the Router back to the old one.
View 9 Replies View RelatedI have a small business environment that uses a domain controller and supports about 50+ PCs. Starting this morning multiple computers have lost their ability to obtain an IP address. We have rebooted our domain controller and tried various fixes on local machines with no luck.
View 1 Replies View RelatedI can see what MAC addresses have a wireless session and I've used MAC Filtering to stop some MAC addresses from using the network at certain times, but they are still getting through to the internet. I don't know if they were to clone their MAC address as to whether this would show up with the cloned address in active sessions list. How I can stop some users from getting through at certain times? Any utility I can use on my Mac (Mac OS X 10.6. to show which computers/MAC addresses are on the network?
View 5 Replies View Relatedhow to connect two subnets with two switches and one router using router sim software?
View 1 Replies View RelatedCan I connect 2 routers to one phone line so that I can receive a wireless internet connection throughout my house?
View 1 Replies View RelatedHow do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
how to connect 2 routers on different lan
View 3 Replies View RelatedI am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
View 4 Replies View RelatedI have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
View 9 Replies View RelatedI want to connect two routers wirelessly without running cables , any easiest way without cables.
View 1 Replies View RelatedWe sold an ESW 540 switch to a 3COM customer that is replacing old equipment. This replacement will be on different faces so we have to interconnect some 3COM switches to the Cisco equipment. We are installing rigth now and this two situations:
Virtual machines can´t get IP addresses via DHCP (using a different MAC address) when connected to the Cisco switch. Physical machines receive IP addresses from DHCP without problem. This situation never happened with 3COM switches.When we interconect the Cisco Switch to the 3COM switches (not using uplink ports) the connection never goes up. Remembering that 3COM switches are old we fixed the speed to 100 Mbps Full Duplex but it didn't work.
I am trying to portforward so I can host a server of a game I play, but whenever I try to connect to my default gateway it just times out and cannot load.I have done the cmd -> ipconfig/all and I found that my default is 192.168.0.1What do I do
View 6 Replies View RelatedIs there a way to set static ip addresses to each port on at sf 300-08?
View 1 Replies View RelatedI've got a LAN with private IPs for the computers, and public, static IPs for the VoIP phones. They are a Hosted VoIP provider, and I want to give priority to the public IPs with my ESW-520-48P switch. How do I implement that in this switch?
I have no roles assigned on the ports and no VLANs setup either. I had tried segregating the VLANs first, but eliminated that route. It's all VLAN 1 now in the switch again. For some reason when I implemented VLAN 100 for voice, voice stopped working on the phones, but data was still fine.
I recently moved out of state and have been working remotely. I just got a new internet provider who will not let me connect to my office VPN without a small business account which is ridiculous. I've been reading up on how to work around this and haven't been able to figure anything out. I've signed up for a dynDNS account but the truth is I have zero experience with this and don't know what I'm doing - most of the stuff I'm reading is a foreign language to me. I can log into my router and change settings and I can get VPN info from my tech person and work so I just need to know what to do. I can't really work effectively without access to my network but I refuse to pay for a small business account
View 5 Replies View RelatedI'm trying to access 192.168.0.1 to configure my linksys router to add new hardware to my home network but my browser (Safari) can not open the page - error message suggests 'server where this page is located isn't responding.
View 3 Replies View Relatedwith a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
View 3 Replies View RelatedFirst , I have installed the router and modem correctly , and i connected it to the switch , So the other devices connected to the internet but not connected to the workgroup so i can't share the files between the PC's ? Modem >>> Router >>> Switch >>> PC's
View 1 Replies View RelatedI have two dvr 4 channel each and I need to connect them to just one static IP, is that possible?
View 1 Replies View Relatedi was trying connecting two LAN network on different location.
View 2 Replies View RelatedI have a Belkin Wireless G Plus MIMO Router and had no problems connecting to corporate in the past until several months ago. I can connect just fine if I bypass the router and connect to the modem. I also have no problem if I go to places like Subway. There is no problem with the wireless internet connection, only a problem when I try to connect to corporate through the VPN.
View 3 Replies View RelatedI have 4 computers on LAN using a router and I cannot see eachother, don't know how to configure the PCs. The router is set on DHCP for LAN, the PCs are using Windows 7 and can connect through the internet the router is providing (4 dells) but don't know how to set the computers to see eachother and to share files.
View 2 Replies View RelatedCan conect to the internet but unable to connect to 192.168.0.1
View 4 Replies View Related