A Telindus 1421 SHDSL Router and a Sagem F@st 1500WG wireless adsl router.The question is: Can i connect this two devices directly over the adsl port and share networks on each side of each of the devices?
I have CentOS and the application I am running does not listen on 192.168.1.5 (Private IP address). Right now I have connected using bridge mode and I can see in my network configuration-> ppp and eth0. PPP has public IP and eth0 has private IP. Is there any way that I can get public ip assigned to eth0? I do not have Static IP, I want to use the public dynamic IP assigned by my ISP to use in eth0 interface.
I have one ADSL router that I have configured Port Forwarding on it, but the internet is very slow. I also have another 3G router and I want to use it for internet because it is much faster, but it cannot do Port Forwarding. How can I connect this two routers in one network such that ADSL router is for Port Forwarding only and 3G router is for internet only?
Have one switch and network.PC number one have win98 and network adapter and connected to the switch.PC number two have winXP and network adapter and connected to the switch same as win98.Network works on win98 and winxp they see each other.internet working on winxp but dont work on win98
I have 3 laptops, 2 tivos, wii, ipad, i touch, etc..... how many items can connect to one router without drops outs? My internet keeps dropping off since my last device connected to my wireless home network and we have to keep hitting the reset button. Do different routers support more devices than others?
Our church has 1 phone line, we run BTBusiness Broadband at one of the building where we have a couple of charities based. We have the phone line connected to an extension at the other end (where the Church is) >80m away. Any way of running a second concurrent router on the extension so I can set up an office with a VOIP number, pC's printers etc there too? We use Devolo ethernet over mains and wireless for the main building, but the church itself is on a completely seperate mains power supply so I can't use that. I could run 100m Cat 5 and locate a switch on that, but any way of achieving something similar over the phone cable which is already in place.
I was using Linksys ADSL router ( WAG120) as modem router. Recently I bought new Linksys x3000 and installed a modem router in place of WAG120. Now i would like to connect the both routers to get the signals in first floor of my house.
We've (an independent school) just bought an SR520 with a view to replacing one of our Draytek 2820s. We need to set up some site-to-site VPN with NAT and the Drayteks won't do it.
I've been trying to configure the SR520 in just the most basic fashion using CCA (3.1) and the CLI but with no success. I can't get a PPP connection with our ISP.
I've tried following the instructions in the software config pdf and also tried replicating the various 'running configs' reported in other posts in this forum to allow connection to a UK ISP, with no success. I don't know how many times I've reset the poor thing to factory defaults.
I have to say that I'm dismayed at how flaky the CCA appears to be. Many of the things I've tried with it simply don't work and often end up in it hanging. Close to useless in my view.
So instead I've tried to use the CLI which seems a lot more solid but is somewhat impenetrable and there's precious little by way of supporting explanation.
i have a belkin wireless router F6D4230-4. the "wired" and "router" lights are green but the "wireless", "modem", and "internet" lights won't come on. when they do, its red. the router is connected but won't pick up in any other rooms or on our phones.
How do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I am trying to connect 2 wireless routers to expand my wireless signal. I want to connect the router 1 (in 2d floor) to a powerline av and then get the router 2 to the powerline (in the ground floor) so i can have wireless there too. I've tried some configurations i found online, but can't get to make the network functioning. The routers and powerline av are all dlink. I don't mind having 2 networks, but it would be better to have only one
I have a laptop connected to a net gear wireless router (for internet), but I am very close to buying a Belkin network USB hub to make my hard drive wireless, but this requires a router. I do not want move my hard drive to where my net gear router is, so I need to get another router, i am looking at a Belkin router so that I can make my hard drive wireless (This is the only reason for the router, it will not be used for internet) so I can keep my hard drive in the same place.
I am trying to portforward so I can host a server of a game I play, but whenever I try to connect to my default gateway it just times out and cannot load.I have done the cmd -> ipconfig/all and I found that my default is 192.168.0.1What do I do
All of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
I recently moved out of state and have been working remotely. I just got a new internet provider who will not let me connect to my office VPN without a small business account which is ridiculous. I've been reading up on how to work around this and haven't been able to figure anything out. I've signed up for a dynDNS account but the truth is I have zero experience with this and don't know what I'm doing - most of the stuff I'm reading is a foreign language to me. I can log into my router and change settings and I can get VPN info from my tech person and work so I just need to know what to do. I can't really work effectively without access to my network but I refuse to pay for a small business account
I'm trying to access 192.168.0.1 to configure my linksys router to add new hardware to my home network but my browser (Safari) can not open the page - error message suggests 'server where this page is located isn't responding.
with a networking issue that I'm having with the 2nd computer I have trying to connect to the interntet via my Westell 7500 DSL router. I ran the diagnostic tool on the NIC to make sure it working correctly and it is, and so is the cable according the tools; I also verified that myself via unplugging/plugging the cable into the router and it detects eachMy other 2 computers work fine via the router.Here is the ipconfig info;Host Name:XXXXXXPrimary Dns Suffix: (blank)Node Type: HybridIP Routing Enabled: NoWINS Proxy Enabled: NoEthernet Adapter Local Area Connection:Connection-specific DNS suffix: (blank)Description: Intel(R) 82562V-2 10/100 Network ConnectionPhysical Address: 00-1D-09-8D-34-3BDHCP Enabled: Yes
First , I have installed the router and modem correctly , and i connected it to the switch , So the other devices connected to the internet but not connected to the workgroup so i can't share the files between the PC's ? Modem >>> Router >>> Switch >>> PC's
I have a Belkin Wireless G Plus MIMO Router and had no problems connecting to corporate in the past until several months ago. I can connect just fine if I bypass the router and connect to the modem. I also have no problem if I go to places like Subway. There is no problem with the wireless internet connection, only a problem when I try to connect to corporate through the VPN.
I have 4 computers on LAN using a router and I cannot see eachother, don't know how to configure the PCs. The router is set on DHCP for LAN, the PCs are using Windows 7 and can connect through the internet the router is providing (4 dells) but don't know how to set the computers to see eachother and to share files.
I'm having trouble trying to connect 3 computers via LAN for gaming using straight Ethernet cables and a net gear router. Only 2 computers seem to connect at a time. All 3 can connect to one another (one at a time) and the I.P. addresses have been set to 192.168.0.1 , 192.168.0.2 and 192.168.0.3. The cables work fine and the computers, but I'm wondering if I'm using the wrong kind of hub/router?