to enable UPNP on a Virgin Media Super Hub, I have tried using both the IP addresses provided by Virgin media (192.168.0.1 and 192.168.100.1) but regardless of which browser I use the page constantly fails to load.
View 2 RepliesI have a VirginMedia 50Mps wireless router that runs 4 wired connections. These are all working fine and have Internet connection. When the router was installed I could also connect to the internet wirelessly on my Laptop which is running Windows Vista Home Premium. But of late I have been unable to connect to the Internet on the Laptop. When you place the mouse pointer over the Icon in the bottom right hand corner, the following message comes up : Currenlty connected to:Unidentified(virginmediaxxxxxxxx) (where xxxxxxxx is a numeric identifier for the modem). Access: Limited connectivity or sometimes it says Access : Local only.
View 4 Replies View RelatedBelkin N600 ADSL Dual Band wireless Router is terrible from my own experience and every article I read from other users on Virgin Media. At minimum, there is a cmpatibility issue. cannot find one article that resolves issues of wireless interuption, slow speeds, and disconnects. I'm ready to dump this 70 GBP device and spend another on netgear.
View 1 Replies View RelatedI have a wired network with 4 XP pro machines on it. It also has a Western Digital 3 TB MyBook NAS. The Internet connection is a Virgin Media Superhub wireless router connected via a fiber optic 60 Mb connection in the upstairs part of the house. Downstairs on the network is a netgear wireless router connected to the virgin router by a 10/100 Ethernet cable. I have a new laptop running windows 7 home premium that connects via either router depending on where it is in the house due to signal strength. If the laptop connects via the Netgear router it can see the whole network including the nas. if it connects using the virgin media router it can not access or see any other computer/nas on the network.
View 9 Replies View RelatedI have a virgin media wireless router which connecting perfectly via wireless connection the other day. All of a sudden it wont connect. I have turned the router on and off, reset the router to factory defaults but it still wont connect. My computer see's the wireless network but it just wont connect
View 3 Replies View RelatedHow do I make my home network secure. I am with virgin media and have a Linksys Router
View 1 Replies View RelatedIm getting really poor performance on my 1841, my intial thoughts was a duplex mismatch however although im getting a few CRC errors (root cause unknown at this point) not enough to suggest that the this is the issue.
Heres the config:
Building configuration.Current configuration : 5274 bytesLast configuration change at 20:31:01 PCTime Sun Dec 18 2011 by admin_xversion 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname xxxxxx!boot-start-markerboot-end-marker!!security authentication failure rate 10 log
I have a Virgin Superhub at home which is capable of 2.4 OR 5GHz wireless. I have a mixture of 2.4 and 5 GHz tech at home so would like to use dual band. My wireless settings on my Superhub modem look like this.As you can see it has settings for 2.4 OR 5GHz and wireless modes of 54, 144 or 300Mbps.
What setting should I be using for my EA4500 to operate in dual band mode? I'm guessing I should put by Virgin Superhub modem in modem mode at 5GHz/300Mbps.I will besetting up seperate SSIDs for 2.4 and 5GHz bands.
Virgin Media just upgraded my broadband to 100mbps. My main PC is in a place where unfortunately I cannot hard wire it to ethernet, and also the wifi signal is a bit rubbish - therefore I have been using D-Link Powerline AV Homeplugs DHP-307 200Mbps (N.B. I am fully aware that 200mbps doesn't really mean that through homeplugs, please read on)
Ages ago when my I first set this up my connection speed from Virgin Media was 50mbps and, after installing, I tested it a few times and got about 45mbps, which I was happy with.
However, due to the upgrade I thought I would test it again, and now I'm only gettin about 20-25Mbps. I did some diagnistic checks as follows:
A laptop plugged directly into my router via ethernet got 97 Mbps My laptop sitting next to my PC connected via wifi got 54 Mbps My PC connected via wifi with the ethernet/homeplug disconnected got 26 Mbps (I think my wireless card in the PC and the aeriel are both a bit rubbish though anyway)My PC connected via ethernet homeplug with no wifi got 23 Mbps
What I don't understand is:
1 - In the configuration utility for the homeplugs it says that the link speed for this plug is 96 Mbps, so how come that's not coming through?
2 - Why would it have one time been higher and now not? If it wasn't for point 1 above I might put it down to interference in the elecrical circuits, but I thought that's what the link speed would be showing me
I guess the best option would be to try and get VM to install a proper ethernet port in my study, however I can't imagine how they would do this without running cables through the house, which I don't want, so I'm trying to exhaust other options. I'm happy to ditch the homeplugs if there is something better.
Lost connection to Internet though router appears normal. Belkin router, MacBook.
View 1 Replies View RelatedI can't get my Phillips wireless notebook to connect to my virgin media hub, it connected before with a router but not this new one.
View 1 Replies View RelatedI have a Sony Viao Model No-VGN-CS32GH, INTEL PENTIUM PROCESSOR T4200(2GHZ), WINDOWS VISTA HOME BASIC(32-BIT), MEMORY 2GB, HARD DISK DRIVE 250 GB, WIRELESS ADAPTOR-ATHEROS AR928X.I cant seem to connect to the wireless network virgin media 6582156 at my place.For some reason it connects half way to the network but not to the internet?
View 5 Replies View RelatedI cannot open router settings... I had recently opened some ports on my router. However today I tried to access the settings and all it does is a web search for the gateway (192.168.1.254). The internet is working. I reset the router and it did not work. I cannot do a hard reset because I will lose all my settings for my company's settings. Also the router is a Netopia modem/router
View 2 Replies View RelatedI've been trying to set up my TP-Link WR740N router but it always give the error "Failed to Verify router settings" on the last step of the set up screen. Broadband: Globe broadband (Wired)Modem: Siemen Gigaset SE260 I'm also confused on the 2nd Set up screen, it gives the option to select Dynamic IP Static IP PPoEI've tried using the Dynamic IP and PPoE but still getting the same error message
View 1 Replies View RelatedI was just recently hired in my company, we have an sf300-24p switch but I cant find the console cable for it, I think it needs a female to female db9 serial cable, all I have is a DB9 serial to rj45 console cable for the 2801 router, also I cant find the IP address of the sf300 switch, it is directly connected to the 2801 router, I issued a show arp to the router but didnt find the switch's IP add for web access, to sum it up I have no way of configuring the switch, is there any way to find the IP address of the switch? It also dosnt show on show cdp neighbors?
View 13 Replies View Relatedi recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies View RelatedHave a PS3 that will connect to my wrt120n if I unplug the modem and router then plug back in after 2 minutes. if I shut off my PS3 or after approx 1 hour, PS3 drops my connection. I'm trying to access my router page online but after entering the default into my browser, the pop up box will not accept any combo of entries to allow me access. I have an SSID name and my router is password protected. It does not connect me when I use any combo of user name or password or the default "admin".
View 2 Replies View RelatedI tried to log on to my wireless routers IP address but it only gives me a blank page after signing in. the IP address is 192.168.1.1. Is there a problem with this ip address?
View 1 Replies View RelatedI purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server. I click them and nothing happens.Also, the Cisco light on the router keeps blinking.
View 5 Replies View RelatedI have the E3000 and have attched a WD 1TB USB drive. I set it up for FTP and Media sharing and it worked fine but somehow recently I could not connect anymore. I checked the router and all of my setting for the FTP and Media server were gone. The disk drive still shows avaiable but now it shows the entire 1TB free (it was at least half used). This is the second time this has happened, first I tjhought it was a bad disk and replaced it but now it happened again. I did do a power cycle some time ago but I remember it still work after that. Not sure why I am losing my settings. This does not give me a comfort level as to storing anything valuable on that drive.
View 1 Replies View RelatedI have te E4200. When I backed up and restored my media server settings were not there as well as ftp, I found this out upgrading to 1.0.02 that turned out to be a huge waste of time anyways.
View 7 Replies View RelatedI have a WRT54G router and for some reason I'm unable to receive the media stream at my home, but when I connected to my friends N-type router it works fine. I have no other connectivity issues. The only thing that I remember doing that may have caused this was to upgrade my firmware because my droid phone wouldn't connect.
View 8 Replies View RelatedThere are several features that don't work and are returning errors. For starters, when trying to save settings for media/device prioritization I am receiving a 2123 error message. Unable to save settings. EA4500/N900 Router, Cisco Cloud Connect.
View 3 Replies View RelatedI have an Iball Baton Router. I am not able to connect to it from my PC. However, I am able to connect to the router from my Laptop.I have tried isconnecting and renewing the ip. Can see that ip (192.168.1.102) is issued to my PC and can ping to the same. But, do not get any reply when I ping to the gateway (192.168.1.1 - ip for the router). My OS is Windows 7 64 bit.Let me know if you need any more information
View 8 Replies View RelatedFor some port fowarding reasons I have to change my router setting to these:Maximum Ports: 4096TCP Timeout (in seconds): 600UCP Timeout (in seconds): 120I am using a Realtek router ( Family PCI-E Gigabit Ethernet <NDIS 6.20>)This is supposed to be EXTREMELY easy but I lack any general computer knowledge whatsoever. In laymen's term, I am N00B.
View 1 Replies View RelatedI have installed a DIR615 N Router and can get onto the Internet on the PC, but when I type in the device IP address it comes up with an "error" message so I cannot configure it.
View 6 Replies View RelatedI try to login to my router http://192.168.1.1/ I try and put in the user name and password that I think it is. Is it the user name and password you set up or one that's already there and if so where can I find it??
View 6 Replies View Relatedi have a ZyXel prestige 650H-31 Model # router and i'm not able to go on to configuration page of the router i tried 192.168.1.1 several times, even after system reboot and router reset, but of no use. I've a wire connection with desktop (RJ-45 port) not USB AND MY PPPoE lights never lit. originally when i entered the gateway 192.168.1.1 it asked me for username & password, since i didn't have the password at that time i tried to reset the router but after that when ever i entered 192.168.1.1 in the browser it never came up with the option to enter user name & password. I've checked all the wires are also connected. I tried prompt command and it showed that timed out thrice and then sent= 4 received= 0 lost= 100%. I had D-Link router prior to it and later connected the D-Link router an i was able to get connected to net and browse normally.
View 1 Replies View RelatedI have a Hawking 300N and I have misplaced my disk and I neing walked through this to have it set back up. I hooked it all up correctly and it says no internet connection
View 1 Replies View Relatedi am unable to configure my netgear router with my clear modem
View 1 Replies View Relatednew instal will not give me page to enter password
View 1 Replies View RelatedI am unable to see my network media player (wired CAT6 or wireless) using the SAMBA Share feature. My UPNP works fine. I do not have this issue when I am using the Linksys WRT54G or a Netgear WNDR3700 (I returned it to give the E3000 a try) - so I know all my share persmissions and device firewall is turned off. How do I get it to work with the E3000? I want to be able to transfer and stream media files to my media player using SAMBA. Usually my network media player automatically detects SAMBA Servers/Devices and adds it to its list for me to access. But when I use the E3000 that is not the case.
View 4 Replies View RelatedHow can I access this router?
View 2 Replies View Related