Virgin Media Router - Can't Connect To Wireless Network
Feb 6, 2011
I have a virgin media wireless router which connecting perfectly via wireless connection the other day. All of a sudden it wont connect. I have turned the router on and off, reset the router to factory defaults but it still wont connect. My computer see's the wireless network but it just wont connect
View 3 Replies
ADVERTISEMENT
Jan 7, 2012
I have a VirginMedia 50Mps wireless router that runs 4 wired connections. These are all working fine and have Internet connection. When the router was installed I could also connect to the internet wirelessly on my Laptop which is running Windows Vista Home Premium. But of late I have been unable to connect to the Internet on the Laptop. When you place the mouse pointer over the Icon in the bottom right hand corner, the following message comes up : Currenlty connected to:Unidentified(virginmediaxxxxxxxx) (where xxxxxxxx is a numeric identifier for the modem). Access: Limited connectivity or sometimes it says Access : Local only.
View 4 Replies
View Related
Feb 8, 2011
I can't get my Phillips wireless notebook to connect to my virgin media hub, it connected before with a router but not this new one.
View 1 Replies
View Related
May 11, 2012
Virgin Media just upgraded my broadband to 100mbps. My main PC is in a place where unfortunately I cannot hard wire it to ethernet, and also the wifi signal is a bit rubbish - therefore I have been using D-Link Powerline AV Homeplugs DHP-307 200Mbps (N.B. I am fully aware that 200mbps doesn't really mean that through homeplugs, please read on)
Ages ago when my I first set this up my connection speed from Virgin Media was 50mbps and, after installing, I tested it a few times and got about 45mbps, which I was happy with.
However, due to the upgrade I thought I would test it again, and now I'm only gettin about 20-25Mbps. I did some diagnistic checks as follows:
A laptop plugged directly into my router via ethernet got 97 Mbps My laptop sitting next to my PC connected via wifi got 54 Mbps My PC connected via wifi with the ethernet/homeplug disconnected got 26 Mbps (I think my wireless card in the PC and the aeriel are both a bit rubbish though anyway)My PC connected via ethernet homeplug with no wifi got 23 Mbps
What I don't understand is:
1 - In the configuration utility for the homeplugs it says that the link speed for this plug is 96 Mbps, so how come that's not coming through?
2 - Why would it have one time been higher and now not? If it wasn't for point 1 above I might put it down to interference in the elecrical circuits, but I thought that's what the link speed would be showing me
I guess the best option would be to try and get VM to install a proper ethernet port in my study, however I can't imagine how they would do this without running cables through the house, which I don't want, so I'm trying to exhaust other options. I'm happy to ditch the homeplugs if there is something better.
View 1 Replies
View Related
Jun 13, 2012
I have a Sony Viao Model No-VGN-CS32GH, INTEL PENTIUM PROCESSOR T4200(2GHZ), WINDOWS VISTA HOME BASIC(32-BIT), MEMORY 2GB, HARD DISK DRIVE 250 GB, WIRELESS ADAPTOR-ATHEROS AR928X.I cant seem to connect to the wireless network virgin media 6582156 at my place.For some reason it connects half way to the network but not to the internet?
View 5 Replies
View Related
Oct 19, 2012
I have a wired network with 4 XP pro machines on it. It also has a Western Digital 3 TB MyBook NAS. The Internet connection is a Virgin Media Superhub wireless router connected via a fiber optic 60 Mb connection in the upstairs part of the house. Downstairs on the network is a netgear wireless router connected to the virgin router by a 10/100 Ethernet cable. I have a new laptop running windows 7 home premium that connects via either router depending on where it is in the house due to signal strength. If the laptop connects via the Netgear router it can see the whole network including the nas. if it connects using the virgin media router it can not access or see any other computer/nas on the network.
View 9 Replies
View Related
Jul 25, 2011
How do I make my home network secure. I am with virgin media and have a Linksys Router
View 1 Replies
View Related
Jan 7, 2013
to enable UPNP on a Virgin Media Super Hub, I have tried using both the IP addresses provided by Virgin media (192.168.0.1 and 192.168.100.1) but regardless of which browser I use the page constantly fails to load.
View 2 Replies
View Related
Dec 17, 2011
Im getting really poor performance on my 1841, my intial thoughts was a duplex mismatch however although im getting a few CRC errors (root cause unknown at this point) not enough to suggest that the this is the issue.
Heres the config:
Building configuration.Current configuration : 5274 bytesLast configuration change at 20:31:01 PCTime Sun Dec 18 2011 by admin_xversion 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname xxxxxx!boot-start-markerboot-end-marker!!security authentication failure rate 10 log
View 7 Replies
View Related
Oct 20, 2012
Belkin N600 ADSL Dual Band wireless Router is terrible from my own experience and every article I read from other users on Virgin Media. At minimum, there is a cmpatibility issue. cannot find one article that resolves issues of wireless interuption, slow speeds, and disconnects. I'm ready to dump this 70 GBP device and spend another on netgear.
View 1 Replies
View Related
Apr 18, 2012
I've enabled the Media Server on my E3000 router. My PS3 can see the server and play media from it by my PCs can't!
I'm using Windows Media Player v 12.0 on Windows 7 and some older version on Windows XP and it's my understanding that the Media Server should appear under the "Other Libraries" section but it does not.
Am I doing something wrong? Is there a bug in the E3000 firmware (I have the latest as of this date) or is the Media Server simply not compatible with Windows Media Player? compatible media player for Windows 7?
I did read a post about a firmware upgrade on the 4200 that broke the media player, but I don't know if such a problem exists for the E3000.
View 1 Replies
View Related
Jul 17, 2011
Connecting E4200 media server (external hard drive connected to USB in router) to PS3.mapped External HD to media server folder. and enabled UPnP Media Server. after trying all options I can't see media server in PS3.
View 6 Replies
View Related
Aug 9, 2011
I have a wireless N router (DIR-655) in bridge mode connected to a TWC combo modem/wireless G router. I have Tversity media server running on a computer connected to the TWC, but my PS3 which is connected wirelessly to the TWC combo can't see Tversity. What am I missing? Do I need to forward some port from somewhere? FYI, I'm set-up this way so my N router can deliver full N speed, and my G devices connect to the slower TWC router. Everything sees the internet with no problem. Also, to note that devices connected to the D-link can see Tversity, but devices connected to the TWC cannot see Tversity
View 4 Replies
View Related
Mar 10, 2012
I have been using the e4200 for about a week. So far, so good! However, a primary reason I purch it was the ability to share via USB across my network (Files and such). Read the approved USB drives that r compatible and although my specfic drive was not listed (WD, my Passport) I connected it to the e4200 and set a folder called "movies"to share. In this folder I have both bluray rips (25-32GB) and standard rips (5gb or less). Regardless of source, the content was not playable. It buffered like crazy. So, is it as simple as using an approved USB drive and I will be able to share appropriately?
The same folder plays great when connected directly to one of my media streamers USB drive, so don't think the drive/source is bad.
View 2 Replies
View Related
Apr 26, 2012
My router has a main network name (SSID) and media network name (SSID). I know how to change the main network name (SSID) but I don't remember exactly how I can change media network name (SSID).
View 6 Replies
View Related
Feb 11, 2012
I have a 1TB USB hard drive attached to my E3000 (current firmware), I use it for FTP and Shared Media on my network. Recently I have noticed that I have files out there that have 0 KB in size (file names/details are still these), I re-upload the files to the folders and during the upload the correct file size shows but a bit later(within minutes) they all show 0 KB again. I have not seen this type of behavior on an HD before. Additionally, I added some 20 mp3 files to the FTP site, same thing happened but then I zipped up the 20 mp3 files and the zip file uploaded with not problems and is still there with its proper file size, of course this is not a solution when I want to play media files on my TV.
View 2 Replies
View Related
Sep 28, 2012
I have a Virgin Superhub at home which is capable of 2.4 OR 5GHz wireless. I have a mixture of 2.4 and 5 GHz tech at home so would like to use dual band. My wireless settings on my Superhub modem look like this.As you can see it has settings for 2.4 OR 5GHz and wireless modes of 54, 144 or 300Mbps.
What setting should I be using for my EA4500 to operate in dual band mode? I'm guessing I should put by Virgin Superhub modem in modem mode at 5GHz/300Mbps.I will besetting up seperate SSIDs for 2.4 and 5GHz bands.
View 3 Replies
View Related
Mar 19, 2011
getting my computer connected to the internet.I have a fresh install of XP Media Center Edition with SP2. I don't really have anything else installed as I wanted to make sure my internet connection was working to get updates. My computer is a Dell XPS720 desktop I have a DSL connection with [URL] and a Dlink Wireless Router DIR655.I have two portable computers that are on the local network with wireless connections and they are working o.k.On my desktop at the command prompt; I cannot "ping" anything and "ipconfig /all" returns nothing at all.
View 3 Replies
View Related
Aug 11, 2011
I have just setup a E2000 at home. All the wireless connections work and also my NAS server who i wired. But when i try to setup my wired media server it will not connect.
View 6 Replies
View Related
Jul 26, 2010
I am unable to see my network media player (wired CAT6 or wireless) using the SAMBA Share feature. My UPNP works fine. I do not have this issue when I am using the Linksys WRT54G or a Netgear WNDR3700 (I returned it to give the E3000 a try) - so I know all my share persmissions and device firewall is turned off. How do I get it to work with the E3000? I want to be able to transfer and stream media files to my media player using SAMBA. Usually my network media player automatically detects SAMBA Servers/Devices and adds it to its list for me to access. But when I use the E3000 that is not the case.
View 4 Replies
View Related
Sep 28, 2010
So I am on my second HDD with Iomega. I am thinking now that this is a router problem rather than a HDD problem. I have a 1TB Iomega home media network drive, eversince I bought my router and began using it I have been unable to use my HDD. It is hard wired to the router via RJ-45 cable and both units have been reset and powered up in about every order you can imagine. I have reset factory defaults on the router and made security changes to ensure there was nothing blocking that port. I am at wits end. I cannot connect to the HDD and the drive flashes yellow and blue indicating it cannot estabilsh or receive an IP address from the router.
View 6 Replies
View Related
Jan 26, 2013
I'm trying to set up an Iomega Home Media Network Cloud NAS and I'm having problems with opening ports 50500-50599. I have opened port 80 and 443 successfully and included the above port range above as well, but when I check it on www.yougetsignal.com the ports 50500-50599 are still closed. I even tried to split the range in two parts, and still no success. I have been in contact with my ISP and confirmed they do not block any ports in the 50500-50599 range and that the cable modem (a Motorola SBV5120) is operating in Bridge Mode.
View 3 Replies
View Related
Aug 4, 2011
I recently replaced my Linksys WRV54G with a Linksys e2000 where I stream H.264 vido in 480p from one computer connected over gigabit to my Media Center running on Windows 7 64 bit connected at 10/100.
Before the router change, I was able to playback video over the network with no problems. If I connect the Linksys WRV54G again, the issue goes away. The Linksys WRV54G does not have gigabit and I have read related issues of video stuttering over gigabit.
View 4 Replies
View Related
May 29, 2012
I have searched so many threads concerning the problem I am having but have yet to find anything that works.On Sunday my husband changed our router. We have just moved from Sky to Talk Talk. Before the change, my wireless connection was absolutely fine.Now, everything else in the house is working on wireless fine (xBox, my smartphone, hubby's PC) except for my crappy Lenovo N 500 (XP SP3).Here is a copy/paste from my ipconfig /all:[CODE]
View 19 Replies
View Related
May 25, 2011
I am trying to connect to my son's wireless internet with my own laptop. I can't get it to connect - I have tried to "renew IP address" and it doesn't work. I also got a message when I went to Start Run, etc etc "no operation can be performed on Wireless network while is has its media disconnected" I am able to connect to my own wireless internet at home on same laptop.
View 1 Replies
View Related
Apr 19, 2011
Trying to establish a wireless connection from WD TV Live Plus unit to Westell 327W router using an AirLink 150 adapter. The media player sees my network and seems to have a good signal, but keeps telling me "limited or no connectivity." The media player (with adapter) is about 20 feet from the router with direct line-of-sight.Also, 3 other Wi-Fi devices having no problem connecting anywhere in the house.Power down/power up, move adapter to alternate USB port, re-try connection multiple times.
View 4 Replies
View Related
Feb 6, 2012
How do I configure a local area net work with unbounded media?
View 1 Replies
View Related
Feb 20, 2012
I have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.
View 4 Replies
View Related
May 24, 2011
I purchased a Virgin Mobile Online Stick where you do not need a telephone jack, modem, router etc. or anything to go online, It's like, go online from everywhere, like at&t offers it too. Costs like 40-50 bucks a month.But I cannot go online. i insalled the stick and when open the icon, it connects and says ready, but I cannot reach ANY site at all.I saw in the network section that there is a little red x infront of the locale area connection and it always says, connect a cable. But this should not be the cae since you do not need any kind of cables with this stick.A friend of mine and I had the same stick from at&t and it worked perfect. We just double clicked the at&t icon on the desktop, clicked connect and everythng was great and we used it to 100% in the car missing or doing wrong?PS: PC runs on Vista AND, when calling Virgin, they just tell you, that's not there problem because it shows that it is connected, which is true, but still cant reach ANY website
View 1 Replies
View Related
May 26, 2011
I am seeing the following once I run the cmd.
Tunnel adapter Local Area Connection* 11
Media State . . . . . . Media disconnected
Connection-specific DNS Suffix
I cannot connect to the internet.
View 1 Replies
View Related
Aug 16, 2012
New Router - Setup went easy. Create a folder named Media - copy a few formats in only 6 files all less than 2gb in size, 2 x avi (divx/xvid), mp3, mkv, mp4 and flv. All excited I scoot over to the PS 3 - righto we can do this!! Only to see no titles found. Great stuff Go to router - media server - scan - database updated - awesome let's try again! No titles found. Ok?!? Reboot router - reboot ps3. Still frowning - no titles found?
View 1 Replies
View Related
May 15, 2012
I just setup the Linksys EA4500 router on my computer and I am able to hook up to the internet on my computer and on my Logitech Revue. How do I access the media server? It is not showing up on the Logitech Revue or my Samsung TV
View 9 Replies
View Related
Nov 30, 2012
I installed w8 2 hours ago. I just hate they messed with evething but that is not the problem. Aftyer that I haven't beeb able to connect to Virgin broadband. I have to use a donle because my pc has not a wireless adapter. After installation it looks the dongle don't work because not lights come out of it (always b4 there was a light). I talk to someone on the phone but couldn't resolve the problem. They are just going to send a new one. At the moment I'm using 3 mobile wich I cancelled in favour of Virgin wich is not really so good. The is up to 60 Mb but it never goes over 10 MB.
View 1 Replies
View Related