Router Cannot Access Or See Any Other Computer On Virgin Media
Oct 19, 2012
I have a wired network with 4 XP pro machines on it. It also has a Western Digital 3 TB MyBook NAS. The Internet connection is a Virgin Media Superhub wireless router connected via a fiber optic 60 Mb connection in the upstairs part of the house. Downstairs on the network is a netgear wireless router connected to the virgin router by a 10/100 Ethernet cable. I have a new laptop running windows 7 home premium that connects via either router depending on where it is in the house due to signal strength. If the laptop connects via the Netgear router it can see the whole network including the nas. if it connects using the virgin media router it can not access or see any other computer/nas on the network.
View 9 Replies
ADVERTISEMENT
Jan 7, 2013
to enable UPNP on a Virgin Media Super Hub, I have tried using both the IP addresses provided by Virgin media (192.168.0.1 and 192.168.100.1) but regardless of which browser I use the page constantly fails to load.
View 2 Replies
View Related
Feb 6, 2011
I have a virgin media wireless router which connecting perfectly via wireless connection the other day. All of a sudden it wont connect. I have turned the router on and off, reset the router to factory defaults but it still wont connect. My computer see's the wireless network but it just wont connect
View 3 Replies
View Related
Jul 25, 2011
How do I make my home network secure. I am with virgin media and have a Linksys Router
View 1 Replies
View Related
Jan 7, 2012
I have a VirginMedia 50Mps wireless router that runs 4 wired connections. These are all working fine and have Internet connection. When the router was installed I could also connect to the internet wirelessly on my Laptop which is running Windows Vista Home Premium. But of late I have been unable to connect to the Internet on the Laptop. When you place the mouse pointer over the Icon in the bottom right hand corner, the following message comes up : Currenlty connected to:Unidentified(virginmediaxxxxxxxx) (where xxxxxxxx is a numeric identifier for the modem). Access: Limited connectivity or sometimes it says Access : Local only.
View 4 Replies
View Related
Dec 17, 2011
Im getting really poor performance on my 1841, my intial thoughts was a duplex mismatch however although im getting a few CRC errors (root cause unknown at this point) not enough to suggest that the this is the issue.
Heres the config:
Building configuration.Current configuration : 5274 bytesLast configuration change at 20:31:01 PCTime Sun Dec 18 2011 by admin_xversion 15.1no service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname xxxxxx!boot-start-markerboot-end-marker!!security authentication failure rate 10 log
View 7 Replies
View Related
May 11, 2012
Virgin Media just upgraded my broadband to 100mbps. My main PC is in a place where unfortunately I cannot hard wire it to ethernet, and also the wifi signal is a bit rubbish - therefore I have been using D-Link Powerline AV Homeplugs DHP-307 200Mbps (N.B. I am fully aware that 200mbps doesn't really mean that through homeplugs, please read on)
Ages ago when my I first set this up my connection speed from Virgin Media was 50mbps and, after installing, I tested it a few times and got about 45mbps, which I was happy with.
However, due to the upgrade I thought I would test it again, and now I'm only gettin about 20-25Mbps. I did some diagnistic checks as follows:
A laptop plugged directly into my router via ethernet got 97 Mbps My laptop sitting next to my PC connected via wifi got 54 Mbps My PC connected via wifi with the ethernet/homeplug disconnected got 26 Mbps (I think my wireless card in the PC and the aeriel are both a bit rubbish though anyway)My PC connected via ethernet homeplug with no wifi got 23 Mbps
What I don't understand is:
1 - In the configuration utility for the homeplugs it says that the link speed for this plug is 96 Mbps, so how come that's not coming through?
2 - Why would it have one time been higher and now not? If it wasn't for point 1 above I might put it down to interference in the elecrical circuits, but I thought that's what the link speed would be showing me
I guess the best option would be to try and get VM to install a proper ethernet port in my study, however I can't imagine how they would do this without running cables through the house, which I don't want, so I'm trying to exhaust other options. I'm happy to ditch the homeplugs if there is something better.
View 1 Replies
View Related
Feb 8, 2011
I can't get my Phillips wireless notebook to connect to my virgin media hub, it connected before with a router but not this new one.
View 1 Replies
View Related
Oct 20, 2012
Belkin N600 ADSL Dual Band wireless Router is terrible from my own experience and every article I read from other users on Virgin Media. At minimum, there is a cmpatibility issue. cannot find one article that resolves issues of wireless interuption, slow speeds, and disconnects. I'm ready to dump this 70 GBP device and spend another on netgear.
View 1 Replies
View Related
Jun 13, 2012
I have a Sony Viao Model No-VGN-CS32GH, INTEL PENTIUM PROCESSOR T4200(2GHZ), WINDOWS VISTA HOME BASIC(32-BIT), MEMORY 2GB, HARD DISK DRIVE 250 GB, WIRELESS ADAPTOR-ATHEROS AR928X.I cant seem to connect to the wireless network virgin media 6582156 at my place.For some reason it connects half way to the network but not to the internet?
View 5 Replies
View Related
Apr 18, 2012
I've enabled the Media Server on my E3000 router. My PS3 can see the server and play media from it by my PCs can't!
I'm using Windows Media Player v 12.0 on Windows 7 and some older version on Windows XP and it's my understanding that the Media Server should appear under the "Other Libraries" section but it does not.
Am I doing something wrong? Is there a bug in the E3000 firmware (I have the latest as of this date) or is the Media Server simply not compatible with Windows Media Player? compatible media player for Windows 7?
I did read a post about a firmware upgrade on the 4200 that broke the media player, but I don't know if such a problem exists for the E3000.
View 1 Replies
View Related
Feb 20, 2012
I have a problem with the e4200 router and a mybook 1 TB connected to it. The media server works fine but after a while i loose contact with the router and the server this means that the Cisco connect doesn't work, the 192.168.1.1 doesn't work and I can't find the disk via \. I do have internet connection via wifi as im using it now....why I loose connection to the router? The lease time is 24h and it can happen more than once in a day.
View 4 Replies
View Related
Apr 16, 2013
I will be working from home half the time and am trying to get set up. So here it goes:
Took PC #1 home and hooked everything up. Could access Internet.Had to bring PC #2 home because #1 didn’t have the programs I needed.Hooked #2 up, no internet access.Tried different network cable – no access.Tried different router port – no access. (router port light doesn’t illuminate, neither does port on PC)My personal PC that uses the same router has internet access.Hooked #1 back up as a test – could access internet.Hooked up #2 again, did a Run, cmd, ipconfig and got “media disconnected”I brought #2 back in for a PC tech to look at. He hooked it up in his office, had internet access.Took it back home and hooked everything up.The port lights illuminated on startup; but after it got to the desktop, lights are off.Tried ipconfig again, "media disconnected”. IP address doesn’t display.
All the while I have internet access on my own PC, plus when I hook up #1 to the same port using the same cable, I have internet access, which led me to believe it's something wrong with PC #2.Tech is saying it’s a problem with my router (Cisco E2500), which I restarted too.
View 4 Replies
View Related
May 30, 2012
When I'm trying to access the Twonky setting page on http://192.168.1.1:9000/config I get: Access is restricted to MediaServer configuration! Is this normal or not?
View 2 Replies
View Related
Oct 23, 2011
I use to run Twonky media server on my iMac and I was very happy with it. Now I have purchased a Linksys Wifi Router E4200. Twonky server embedded works fine with all my devices except with my Samsung D8000 Led TV. In the Mac version I must identify manually the player (Samsung TV), if not mkv won't play. The question is: How can I select the device in the Linksys E4200? The config page is not available and displays "Access is restricted to mediaserver configuration" E4200 firm V. 1.0.03
View 9 Replies
View Related
Aug 21, 2011
How to access the media server and/or external USB drive on an E4200 from an iPad?
View 1 Replies
View Related
Sep 28, 2012
I have a Virgin Superhub at home which is capable of 2.4 OR 5GHz wireless. I have a mixture of 2.4 and 5 GHz tech at home so would like to use dual band. My wireless settings on my Superhub modem look like this.As you can see it has settings for 2.4 OR 5GHz and wireless modes of 54, 144 or 300Mbps.
What setting should I be using for my EA4500 to operate in dual band mode? I'm guessing I should put by Virgin Superhub modem in modem mode at 5GHz/300Mbps.I will besetting up seperate SSIDs for 2.4 and 5GHz bands.
View 3 Replies
View Related
Jan 1, 2013
I have set up access restriction times for my son (we have wireless access for all systems). I use the MAC address on his systems. Xbox, Kindle Fire and his Laptop. The MAC address are Correct. Here is the problem:
I set the "allow" and times from 6pm - 11:00 pm (while on xmas vacation) - the system works for a while he is shut off as i would like but....
After a period of time the entire house goes off line. I have to reboot the power on e2000 router and then disable the access restrictions. System then works. Problem is repeatable. What is the deal. I have updated firmware already. Otherwise the system works great. Never dies. Just when i set access restricions for a SPECIFIC time it kills entiore houese. BTW i can deny him outright 24/7 and the system idsables his access fine. Its just when i set specific times
View 3 Replies
View Related
Dec 9, 2012
I purchased the EA6500 a few days ago, and when I'm connected to Cisco Connect Cloud I am unable to select Folder Access / FTP Server / Media Server. I click them and nothing happens.Also, the Cisco light on the router keeps blinking.
View 5 Replies
View Related
May 24, 2011
I purchased a Virgin Mobile Online Stick where you do not need a telephone jack, modem, router etc. or anything to go online, It's like, go online from everywhere, like at&t offers it too. Costs like 40-50 bucks a month.But I cannot go online. i insalled the stick and when open the icon, it connects and says ready, but I cannot reach ANY site at all.I saw in the network section that there is a little red x infront of the locale area connection and it always says, connect a cable. But this should not be the cae since you do not need any kind of cables with this stick.A friend of mine and I had the same stick from at&t and it worked perfect. We just double clicked the at&t icon on the desktop, clicked connect and everythng was great and we used it to 100% in the car missing or doing wrong?PS: PC runs on Vista AND, when calling Virgin, they just tell you, that's not there problem because it shows that it is connected, which is true, but still cant reach ANY website
View 1 Replies
View Related
Nov 30, 2012
I installed w8 2 hours ago. I just hate they messed with evething but that is not the problem. Aftyer that I haven't beeb able to connect to Virgin broadband. I have to use a donle because my pc has not a wireless adapter. After installation it looks the dongle don't work because not lights come out of it (always b4 there was a light). I talk to someone on the phone but couldn't resolve the problem. They are just going to send a new one. At the moment I'm using 3 mobile wich I cancelled in favour of Virgin wich is not really so good. The is up to 60 Mb but it never goes over 10 MB.
View 1 Replies
View Related
Jun 26, 2012
Since transferring from a Belkin Wireless Router to the new Virgin Superhub, i am unable to connect to the internet by wireless. Right now i am connected to the ethernet cable attached directly to the hub and it works fine. Also, i have a USB adaptor (which i've just broken ) which also allows me to connect to the internet and works. But i just CAN NOT connect to the internet at all by wireless. For specific example, when i try to connect to Windows Live it tells me that my "Default Gateway" is offline.
View 9 Replies
View Related
Mar 11, 2012
I have a little problem here. I running on my computer (WinXP-SP3) Apache, MySQL, TeamSpeak3, etc.I setting up my router COMTREND Multi-DSL CPE to forward some needed ports to my computer (i use static IP) and it works fine. Anyone from the world can access to my TS3 and Webpage. I have already registered domain name for my Public IP, setting up DNS Server.I have internet access via router and i can connect on my TS3 server, webmail, etc.. ONLY through LOCALHOST. If i want connect via IP/domain_name i just stop on router WebAdmin. Can i access from MY computer to MY computer via public IP and through router?
View 1 Replies
View Related
May 28, 2011
I have a desktop, Sony VAIO laptop, and a Motorola router and modem combination. Both computers are running Windows 7 professional. The desktop is running the 32 bit version and the laptop the 64 bit software.When I first got my router, I could access my laptop from the desktop but after a crash on the desktop and reinstallation of everything, I can no longer access the laptop. I have set up file sharing on the laptop but it still will not allow access. Here is the message that appears when I try go access a folder on the laptop:"Windows cannot access \name-VAIOackups,You do not have permission to access \name-VAIOackups"
View 3 Replies
View Related
Mar 28, 2011
I have Virgin Mobiles 3G stick and have internet on my computer. Is there any way to turn it into a wifi connection to use on my i touch? I dont have any wifi router or anything.
View 3 Replies
View Related
Jul 15, 2012
I recently cleaned my hard drive, but forgot to save my drivers.
Now after installing Windows XP, I can't access the internet and I can't save anything because I keep getting insufficient memory errors (but my drive is almost empty), but I have been able to update drivers.
I have managed to recover some of the drivers but I can't figure out what I have to do to get my desktop to access the web. I have tried directly connecting to my router and using my wireless USB adapter (whose driver I can't install because of an insufficient error message).
My computer is a HP Pavilion Media Center TV m7640n Desktop that I bought several years ago:
[URL]
In device manager, i only have 3 question marks left under Other Devices: Audio Device on High Definition Audio Bus, Compact Wireless-G USB Adapter, and Multimedia Video Controller.
So far I've installed these drivers off the HP website:
Fall 2006 Original NVIDIA LAN Drivers
Fall 2006 Original Asus Modem Drivers
Fall 2006 Original NVIDIA Chipset Drivers
Fall 2006 Original NVIDIA GeForce 6150 LE Graphics Drivers
[URL]
View 4 Replies
View Related
Mar 11, 2011
i cant view my computer on my tv,or reverse, both connected to the hme network
View 3 Replies
View Related
Jan 4, 2012
So I have a really strange problem where I cannot access my credit union's website at all through any computer in my house. I've tried on 3 different laptops both Mac and PC, along with PC desktop and my iPhone.What's weird is that I can access the website on my iPhone if I turn off wifi and use 3G - no problems. But once I'm on the wireless network again it just loads for 20-30 seconds before saying it can't connect to the server. The URL is which I also checked on down for everyone or just me - the results came back immediately saying it's just me!t this point I literally have no idea what to do... tried resetting the router, logging into the admin via 192.168.1.1 and couldn't find any firewalls or blocked URLs. I'm fairly knowledgeable with computers and OS' but networking I'm no savant.
View 6 Replies
View Related
Jan 20, 2012
I bought a wireless router (TP-Link / TL-WR740N) an install it , it works with my laptop and telephone. no problem.now i connected another desktop computer to the router through a wire (LAN port) because the PC has no wire capability , the problem is that i cant access the net.
View 1 Replies
View Related
Nov 13, 2011
I migrated my internet from PPPOE to DHCP. My wifi is working with no problem but when I hook up my computer to 1 of the 4 Lan ports I can't seem to connect to the internet I can however log in my router no problem. But I don't get internet access... I wonder what could be the problem. I tried resetting my router and modem to see if just a bug or something but to no avail.
View 5 Replies
View Related
Dec 15, 2012
Region : Canada
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.12.22 Build 120424 Rel.39632n
ISP :
I can access the USB storage via FTP, but I wanted to access files using a Windows Explorer format. Also, anyone access the Media share ? Manual tells you how to setup the USB functions but not how to access from a PC.
View 1 Replies
View Related
Aug 20, 2012
Have two other computers that connect with ease to the Netgear wireless router, but the new computer will not access the internet. I have been searching for answers and have tried about everything I can find nuder similar posts, but I still have not internet access. At varying times, I have had "internet access", but no actual ability to load websites. Right now, I do not even have access. I am at a loss.Even at my low level of experience, I am usually able to tinker until I fix the problem, but I am about four hours in and currently seem to have taken a step backward. I cannot even begin to explain what things I have already tried
View 9 Replies
View Related
Mar 4, 2012
I am uable to access my files on the USB Storage Device connected to WRT610. Its configured properly. I can see the drive on my network. When I double click it asks for password which I enter and it takes me to the shared folder. But when I click it it says Not Accessible....You donot have the persmission. FTP works fine.I have noticed that on the disk page in the Shared Folder Area when you click on the Summary, the box with Groups With Access is Empty. Whereas on the FTP area in the same summary it clearly mentions the admin group.I have tried every thing including factory reset, hard reset, using new group, new user name etc..The technician from Linsys even spent an hour on my computer and ultimately he gave up and gave me number to contact technical support.
View 1 Replies
View Related
